SIST EN 60512-1-100:2012

Connectors for electronic equipment - Tests and measurements - Part 1-100 Ed 3.0: General - applicable publications

IEC 60512-1-100:2012 provides a listing of the 60512 series of standards for specific tests that are created for connectors. Further it gives cross-references with the former (60)512 standards, where different test numbers were used. The connector tests as such are mainly identical with the previously published standards; minor changes may be introduced due to technical developments (e.g. other soldering temperatures in soldering tests, resulting from the introduction of lead-free soldering). The former issues were in booklets, with several related tests in one document, while the present issues are leaflets, each featuring one single test. This third edition cancels and replaces the second edition published in 2006. This edition constitutes a technical revision. This new edition reflects the status of publications in the IEC 60512 series as of September 1st 2011.

Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 1-100: Allgemeines - Zutreffende Publikationen

Connecteurs pour équipements électroniques - Essais et mesures - Partie 1-100 Ed.3: Généralités - Publications applicables

La CEI 60512-1-100:2012 donne une liste des normes de la série 60512 qui couvrent les essais qui ont été créés spécifiquement pour les connecteurs. En outre, elle indique les correspondances avec les anciennes normes de la série (60)512, lorsque des numéros d'essai différents étaient utilisés. Les essais applicables aux connecteurs, en tant que tels, sont en grande partie identiques à ceux des normes publiées antérieurement; des modifications mineures peuvent être introduites pour tenir compte des évolutions techniques (par exemple, d'autres températures de soudage pour les essais de soudage, suite à l'introduction du soudage sans plomb). Les anciennes publications avaient la forme de recueils, avec plusieurs essais liés dans un même document, tandis que les versions actuelles ont la forme de documents individuels, contenant chacun la description d'un seul essai. Cette troisième édition annule et remplace la deuxième édition parue en 2006. Cette édition constitue une révision technique. Cette nouvelle édition reflète le statut des publications de la série CEI 60512 à partir du 1er septembre 2011.

Konektorji za elektronsko opremo - Preskusi in meritve - 1-100. del: Splošno - Uporabne publikacije

V tem delu standarda IEC 60512 je seznam skupine standardov 60512 za posebne preskuse, ki se izvajajo na konektorjih. Poleg tega vključuje sklicevanja na nekdanje standarde (60)512, v katerih so se uporabljale drugačne številke preskusov. Preskusi konektorjev so večinoma enaki kot pri predhodnih standardih, nekaj manjših sprememb je nastalo zaradi tehničnega razvoja (npr. drugačne temperature mehkega spajkanja, ki so posledica uvedbe spajkanja brez svinca). Predhodni standardi so bili izdani v knjižicah z več zadevnimi preskusi v enem dokumentu, medtem ko so sedanji izdani v obliki posameznih listov, ki vključujejo po en preskus.

General Information

• Status: Published
• Publication Date: 22-May-2012
• ICS: 31.220.10 - Plug-and-socket devices. Connectors
• Technical Committee: I11 - Imaginarni 11
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 16-May-2012
• Due Date: 21-Jul-2012
• Completion Date: 23-May-2012
• Ref Project: EN 60512-1-100:2012 - Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications

Relations

• Revised: SIST EN 60512-1-100:2006 - Connectors for electronic equipment - Tests and measurements -- Part 1-100: General - Applicable publications
• Effective Date: 06-May-2014
• Replaces: SIST EN 60512-1-100:2006 - Connectors for electronic equipment - Tests and measurements -- Part 1-100: General - Applicable publications
• Effective Date: 29-Jan-2023
• Replaces: SIST EN 60512-1-100:2006 - Connectors for electronic equipment - Tests and measurements -- Part 1-100: General - Applicable publications
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60512-1-100:2012
01-julij-2012
Konektorji za elektronsko opremo - Preskusi in meritve - 1-100. del: Splošno -
Uporabne publikacije
Connectors for electronic equipment - Tests and measurements - Part 1-100 Ed 3.0:
General - applicable publications
Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 1-100:
Allgemeines - Zutreffende Publikationen
Connecteurs pour équipements électroniques - Essais et mesures - Partie 1-100 Ed.3:
Généralités - Publications applicables
Ta slovenski standard je istoveten z: EN 60512-1-100:2012
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
SIST EN 60512-1-100:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60512-1-100:2012

---------------------- Page: 2 ----------------------

SIST EN 60512-1-100:2012

EUROPEAN STANDARD
EN 60512-1-100

NORME EUROPÉENNE
May 2012
EUROPÄISCHE NORM

ICS 31.220.10 Supersedes EN 60512-1-100:2006


English version


Connectors for electronic equipment -
Tests and measurements -
Part 1-100: General -
Applicable publications
(IEC 60512-1-100:2012)


Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Essais et mesures - Mess- und Prüfverfahren -
Partie 1-100: Généralités - Teil 1-100: Allgemeines -
Publications applicables Zutreffende Publikationen
(CEI 60512-1-100:2012) (IEC 60512-1-100:2012)





This European Standard was approved by CENELEC on 2012-03-28. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60512-1-100:2012 E

---------------------- Page: 3 ----------------------

SIST EN 60512-1-100:2012
EN 60512-1-100:2012 - 2 -
Foreword
The text of document 48B/2270/FDIS, future edition 3 of IEC 60512-1-100, prepared by SC 48B,
"Connectors", of IEC TC 48, "Electromechanical components and mechanical structures for electronic
equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60512-
1-100:2012.

The following dates are fixed:
(dop) 2012-12-28
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2015-03-28

standards conflicting with the
document have to be withdrawn

This document supersedes EN 60512-1-100:2006.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.

Endorsement notice
The text of the International Standard IEC 60512-1-100:2012 was approved by CENELEC as a European
Standard without any modification.

---------------------- Page: 4 ----------------------

SIST EN 60512-1-100:2012



IEC 60512-1-100

®


Edition 3.0 2012-02




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Connectors for electronic equipment – Tests and measurements –

Part 1-100: General – Applicable publications




Connecteurs pour équipements électroniques – Essais et mesures –

Partie 1-100: Généralités – Publications applicables
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

K
CODE PRIX


ICS 31.220.10 ISBN 978-2-88912-891-4



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 5 ----------------------

SIST EN 60512-1-100:2012
– 2 – 60512-1-100  IEC:2012
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

CONNECTORS FOR ELECTRONIC EQUIPMENT –
TESTS AND MEASUREMENTS –

Part 1-100: General –
Applicable publications

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60512-1-100 has been prepared by subcommittee 48B:
Connectors, of IEC technical committee 48: Electromechanical components and mechanical
structures for electronic equipment.
This third edition cancels and replaces the second edition published in 2006. This edition
constitutes a technical revision.
This new edition reflects the status of publications in the IEC 60512 series as of September
st
1 2011.

---------------------- Page: 6 ----------------------

SIST EN 60512-1-100:2012
60512-1-100  IEC:2012 – 3 –
The text of this standard is based on the following documents:
FDIS Report on voting
48B/2270/FDIS 48B/2281/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
A list of all parts of IEC series 60512, under the general title Connectors for electronic
equipment – Tests and measurements, can be found on the IEC website.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 7 ----------------------

SIST EN 60512-1-100:2012
– 4 – 60512-1-100  IEC:2012
CONNECTORS FOR ELECTRONIC EQUIPMENT –
TESTS AND MEASUREMENTS –

Part 1-100: General –
Applicable publications



1 Scope and object
This part of IEC 60512 provides a listing of
...