Agricultural tractors and machinery - Power take-off drive shafts and power-input connection - Part 2: Specification for use of PTO drive shafts, and position and clearance of PTO drive line and PIC for various attachments

This part of ISO 5673 gives the forms and applications of power take-off (PTO) drive shafts for tractors and
self-propelled machines used in agriculture, and specifies the dimensions for, and clearance zone around, the
implement power-input connection (PIC) for a variety of attachments. Its intent is to ensure proper clearance
between the PTO drive line and adjacent components on the implement and tractor when both implement and
tractor have compatible power levels. It is not intended as a complete guide for drive-line design and does not,
for example, contain information on preventing drive-line vibration or sizing a torque limiting device. It is not
applicable to combinations of implements with tractors having high ground clearance, such as those working
in standing vegetable crops or sugar cane, nor to agricultural tractors designed for low ground clearance, such
as for lawn mowing or ground care, which require a low centre of gravity; neither is it applicable to implements
non-symmetrical in design by necessity due to their function.

Tracteurs et matériels agricoles - Arbres de transmission à cardans de prise de force et arbre récepteur de la machine - Partie 2: Spécifications relatives à l'utilisation des arbres de transmission à cardans de prise de force, et position et dégagement de la ligne de transmission de prise de force et de l'arbre récepteur de la machine pour différents systèmes d'attelage

L'ISO 5673-2:2005 fournit les modèles et les types d'application des arbres de transmission à cardans de prise de force (p.d.f.) pour les tracteurs et les machines automotrices utilisés en agriculture et spécifie les dimensions relatives à l'arbre récepteur sur la machine (a.r.m.) et à sa zone de dégagement pour une variété d'attelages. Elle a pour objet de prévoir un dégagement approprié entre la ligne de transmission à cardans de prise de force et les composants adjacents de l'instrument et du tracteur lorsque tous deux ont des niveaux de puissance compatibles. L'objectif de la présente norme n'est pas de servir de guide complet pour la conception des lignes de transmission. Elle ne comprend, par exemple, aucune information relative à la prévention des vibrations exercées sur les lignes de transmission ni aucune information relative au dimensionnement d'un dispositif de limitation de couple. Les combinaisons d'instruments avec tracteurs à garde au sol élevée, tels que ceux opérant dans les cultures maraîchères sur pied ou les plantations de canne à sucre, voire les tracteurs agricoles conçus pour une garde au sol peu élevée, tels que les tracteurs utilisés pour tondre le gazon ou entretenir le sol, et requérant un centre de gravité peu élevé, ne font pas l'objet de l'ISO 5673-2:2005. Elle ne s'applique pas non plus aux instruments à la conception non symétrique par nécessité en raison de leur fonction.

Kmetijski traktorji in stroji - Priključne gredi in namestitev priključkov - 2. del: Specifikacija za uporabo kardanske gredi, položaj, potrditev kardanske linije in PIC za različne priključke

Ta del standarda ISO 5673 obravnava oblike in uporabe priključnih (kardanskih) gredi za traktorje in stroje z lastnim pogonom, ki se uporabljajo v kmetijstvu, ter določa dimenzije priključka (PIC) na priključnem stroju za različne priključke in neoviran prostor okoli njega. Njegov namen je zagotoviti ustrezen prostor med kardansko linijo in bližnjimi sestavnimi deli na priključnem stroju ter traktorjem, kadar imata priključni stroj in traktor združljivi ravni moči. Njegov namen ni zagotavljati popolna navodila za projektiranje kardanske linije in tako na primer ne vsebuje informacij o preprečevanju vibracij kardanske linije ali določanju velikosti naprav za omejevanje navora. Ne velja za kombinacije priključnih strojev in traktorjev z veliko razdaljo od tal, kot so tisti, ki se uporabljajo na površinah z nepožetimi rastlinskimi pridelki in sladkornim trsom, niti za kmetijske traktorje, namenjene nizki razdalji od tal, kot so traktorji za košenje trave ali obdelavo tal z nizkim težiščem. Prav tako ne velja za priključne stroje, katerih oblika je zaradi njihove funkcije nesimetrična.

General Information

Status
Published
Publication Date
22-Feb-2015
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
11-Feb-2015
Due Date
18-Apr-2015
Completion Date
23-Feb-2015

Relations

Buy Standard

Standard
ISO 5673-2:2005 - Agricultural tractors and machinery -- Power take-off drive shafts and power-input connection
English language
12 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 5673-2:2015
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 5673-2:2005 - Tracteurs et matériels agricoles -- Arbres de transmission a cardans de prise de force et arbre récepteur de la machine
French language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 5673-2
First edition
2005-02-15


Agricultural tractors and machinery —
Power take-off drive shafts and power-
input connection —
Part 2:
Specification for use of PTO drive shafts,
and position and clearance of PTO drive
line and PIC for various attachments
Tracteurs et matériels agricoles — Arbres de transmission à cardans de
prise de force et arbre récepteur de la machine —
Partie 2: Spécifications relatives à l'utilisation des arbres de
transmission à cardans de prise de force, et position et dégagement de
la ligne de transmission de prise de force et de l'arbre récepteur de la
machine pour différents systèmes d'attelage




Reference number
ISO 5673-2:2005(E)
©
ISO 2005

---------------------- Page: 1 ----------------------
ISO 5673-2:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 5673-2:2005(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 2
4 Application and use of PTO drive shafts. 2
5 Position and clearance of PIC for various attachments . 4

© ISO 2005 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 5673-2:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5673-2 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and
forestry, Subcommittee SC 4, Tractors.
This first edition of ISO 5673-2, together with ISO 5673-1, cancels and replaces ISO 5673:1993, of which it
constitutes a technical revision.
ISO 5673 consists of the following parts, under the general title Agricultural tractors and machinery — Power
take-off drive shafts and power-input connection:
 Part 1: General manufacturing and safety requirements
 Part 2: Specification for use of PTO drive shafts, and position and clearance of PTO drive line and PIC for
various attachments
iv © ISO 2005 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 5673-2:2005(E)

Agricultural tractors and machinery — Power take-off drive
shafts and power-input connection —
Part 2:
Specification for use of PTO drive shafts, and position and
clearance of PTO drive line and PIC for various attachments
1 Scope
This part of ISO 5673 gives the forms and applications of power take-off (PTO) drive shafts for tractors and
self-propelled machines used in agriculture, and specifies the dimensions for, and clearance zone around, the
implement power-input connection (PIC) for a variety of attachments. Its intent is to ensure proper clearance
between the PTO drive line and adjacent components on the implement and tractor when both implement and
tractor have compatible power levels. It is not intended as a complete guide for drive-line design and does not,
for example, contain information on preventing drive-line vibration or sizing a torque limiting device. It is not
applicable to combinations of implements with tractors having high ground clearance, such as those working
in standing vegetable crops or sugar cane, nor to agricultural tractors designed for low ground clearance, such
as for lawn mowing or ground care, which require a low centre of gravity; neither is it applicable to implements
non-symmetrical in design by necessity due to their function.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 500-3:2004, Agricultural tractors — Rear-mounted power take-off types 1, 2 and 3 — Part 3: Main PTO
dimensions and spline dimensions, location of PTO
ISO 730-1:1994, Agricultural wheeled tractors — Rear-mounted three-point linkage — Part 1: Categories 1, 2,
3 and 4
ISO 6489-1:2001, Agricultural vehicles — Mechanical connections between towed and towing vehicles —
Part 1: Dimensions of hitch-hooks
ISO 6489-2:2002, Agricultural vehicles — Mechanical connections between towed and towing vehicles —
Part 2: Specifications for clevis coupling 40
ISO 6489-3:2004, Agricultural vehicles — Mechanical connections between towed and towing vehicles —
Part 3: Tractor drawbar
ISO 6489-4:2004, Agricultural vehicles — Mechanical connections between towed and towing vehicles —
Part 4: Dimensions of piton-type coupling
© ISO 2005 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 5673-2:2005(E)
ISO 24347, Agricultural vehicles — Mechanical connections between towed and towing vehicles —
1)
Dimensions of ball-type coupling device (80 mm)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5673-1 apply.
4 Application and use of PTO drive shafts
4.1 Form A
A PTO drive shaft of form A with two universal joints, as shown in Figure 1, compensates for variations in
angle and length of the connecting shafts between PTO and PIC. Equal angles in W- and Z-bends will ensure
uniform transmission of rotary motion.

Figure 1 — PTO drive shaft — Form A

...

SLOVENSKI STANDARD
SIST ISO 5673-2:2015
01-april-2015
1DGRPHãþD
SIST ISO 5673:1995
.PHWLMVNLWUDNWRUMLLQVWURML3ULNOMXþQHJUHGLLQQDPHVWLWHYSULNOMXþNRYGHO
6SHFLILNDFLMD]DXSRUDERNDUGDQVNHJUHGLSRORåDMSRWUGLWHYNDUGDQVNHOLQLMHLQ3,&
]DUD]OLþQHSULNOMXþNH
Agricultural tractors and machinery - Power take-off drive shafts and power-input
connection - Part 2: Specification for use of PTO drive shafts, and position and clearance
of PTO drive line and PIC for various attachments
Tracteurs et matériels agricoles - Arbres de transmission à cardans de prise de force et
arbre récepteur de la machine - Partie 2: Spécifications relatives à l'utilisation des arbres
de transmission à cardans de prise de force, et position et dégagement de la ligne de
transmission de prise de force et de l'arbre récepteur de la machine pour différents
systèmes d'attelage
Ta slovenski standard je istoveten z: ISO 5673-2:2005
ICS:
65.060.10 Kmetijski traktorji in prikolice Agricultural tractors and
trailed vehicles
SIST ISO 5673-2:2015 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 5673-2:2015

---------------------- Page: 2 ----------------------

SIST ISO 5673-2:2015


INTERNATIONAL ISO
STANDARD 5673-2
First edition
2005-02-15


Agricultural tractors and machinery —
Power take-off drive shafts and power-
input connection —
Part 2:
Specification for use of PTO drive shafts,
and position and clearance of PTO drive
line and PIC for various attachments
Tracteurs et matériels agricoles — Arbres de transmission à cardans de
prise de force et arbre récepteur de la machine —
Partie 2: Spécifications relatives à l'utilisation des arbres de
transmission à cardans de prise de force, et position et dégagement de
la ligne de transmission de prise de force et de l'arbre récepteur de la
machine pour différents systèmes d'attelage




Reference number
ISO 5673-2:2005(E)
©
ISO 2005

---------------------- Page: 3 ----------------------

SIST ISO 5673-2:2015
ISO 5673-2:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 5673-2:2015
ISO 5673-2:2005(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 2
4 Application and use of PTO drive shafts. 2
5 Position and clearance of PIC for various attachments . 4

© ISO 2005 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 5673-2:2015
ISO 5673-2:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5673-2 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and
forestry, Subcommittee SC 4, Tractors.
This first edition of ISO 5673-2, together with ISO 5673-1, cancels and replaces ISO 5673:1993, of which it
constitutes a technical revision.
ISO 5673 consists of the following parts, under the general title Agricultural tractors and machinery — Power
take-off drive shafts and power-input connection:
 Part 1: General manufacturing and safety requirements
 Part 2: Specification for use of PTO drive shafts, and position and clearance of PTO drive line and PIC for
various attachments
iv © ISO 2005 – All rights reserved

---------------------- Page: 6 ----------------------

SIST ISO 5673-2:2015
INTERNATIONAL STANDARD ISO 5673-2:2005(E)

Agricultural tractors and machinery — Power take-off drive
shafts and power-input connection —
Part 2:
Specification for use of PTO drive shafts, and position and
clearance of PTO drive line and PIC for various attachments
1 Scope
This part of ISO 5673 gives the forms and applications of power take-off (PTO) drive shafts for tractors and
self-propelled machines used in agriculture, and specifies the dimensions for, and clearance zone around, the
implement power-input connection (PIC) for a variety of attachments. Its intent is to ensure proper clearance
between the PTO drive line and adjacent components on the implement and tractor when both implement and
tractor have compatible power levels. It is not intended as a complete guide for drive-line design and does not,
for example, contain information on preventing drive-line vibration or sizing a torque limiting device. It is not
applicable to combinations of implements with tractors having high ground clearance, such as those working
in standing vegetable crops or sugar cane, nor to agricultural tractors designed for low ground clearance, such
as for lawn mowing or ground care, which require a low centre of gravity; neither is it applicable to implements
non-symmetrical in design by necessity due to their function.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 500-3:2004, Agricultural tractors — Rear-mounted power take-off types 1, 2 and 3 — Part 3: Main PTO
dimensions and spline dimensions, location of PTO
ISO 730-1:1994, Agricultural wheeled tractors — Rear-mounted three-point linkage — Part 1: Categories 1, 2,
3 and 4
ISO 6489-1:2001, Agricultural vehicles — Mechanical connections between towed and towing vehicles —
Part 1: Dimensions of hitch-hooks
ISO 6489-2:2002, Agricultural vehicles — Mechanical connections between towed and towing vehicles —
Part 2: Specifications for clevis coupling 40
ISO 6489-3:2004, Agricultural vehicles — Mechanical connections between towed and towing vehicles —
Part 3: Tractor drawbar
ISO 6489-4:2004, Agricultural vehicles — Mechanical connections between towed and towing vehicles —
Part 4: Dimensions of piton-type coupling
© ISO 2005 – All rights reserved 1

---------------------- Page: 7 --------------
...

NORME ISO
INTERNATIONALE 5673-2
Première édition
2005-02-15


Tracteurs et matériels agricoles — Arbres
de transmission à cardans de prise de
force et arbre récepteur de la machine —
Partie 2:
Spécifications relatives à l'utilisation des
arbres de transmission à cardans de
prise de force, et position et dégagement
de la ligne de transmission de prise de
force et de l'arbre récepteur de la
machine pour différents systèmes
d'attelage
Agricultural tractors and machinery — Power take-off drive shafts and
power-input connection —
Part 2: Specification for use of PTO drive shafts, and position and
clearance of PTO drive line and PIC for various attachments




Numéro de référence
ISO 5673-2:2005(F)
©
ISO 2005

---------------------- Page: 1 ----------------------
ISO 5673-2:2005(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


©  ISO 2005
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2005 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 5673-2:2005(F)
Sommaire Page
Avant-propos. iv
1 Domaine d'application. 1
2 Références normatives. 1
3 Termes et définitions . 2
4 Application et utilisation des arbres de transmission à cardans de prise de force . 2
5 Position et dégagement de l’arbre récepteur de la machine pour différents systèmes
d’attelage. 4

© ISO 2005 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 5673-2:2005(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 5673-2 a été élaborée par le comité technique ISO/TC 23, Tracteurs et matériels agricoles et forestiers,
sous-comité SC 4, Tracteurs.
Cette première édition de l’ISO 5673-2, conjointement à l’ISO 5673-1, annule et remplace l’ISO 5673:1993,
dont elle constitue une révision technique.
L'ISO 5673 comprend les parties suivantes, présentées sous le titre général Tracteurs et matériels
agricoles — Arbres de transmission à cardans de prise de force et arbre récepteur de la machine:
 Partie 1: Exigences générales de fabrication et de sécurité
 Partie 2: Spécifications relatives à l'utilisation des arbres de transmission à cardans de prise de force, et
position et dégagement de la ligne de transmission de prise de force et de l'arbre récepteur de la
machine pour différents systèmes d'attelage

iv © ISO 2005 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 5673-2:2005(F)

Tracteurs et matériels agricoles — Arbres de transmission à
cardans de prise de force et arbre récepteur de la machine —
Partie 2:
Spécifications relatives à l'utilisation des arbres de
transmission à cardans de prise de force, et position et
dégagement de la ligne de transmission de prise de force et de
l'arbre récepteur de la machine pour différents systèmes
d'attelage
1 Domaine d'application
La présente partie de l’ISO 5673 fournit les modèles et les types d’application des arbres de transmission à
cardans de prise de force (p.d.f.) pour les tracteurs et les machines automotrices utilisés en agriculture et
spécifie les dimensions relatives à l'arbre récepteur sur la machine (a.r.m.) et à sa zone de dégagement pour
une variété d’attelages. Elle a pour objet de prévoir un dégagement approprié entre la ligne de transmission à
cardans de prise de force et les composants adjacents de l'instrument et du tracteur lorsque tous deux ont
des niveaux de puissance compatibles. L'objectif de la présente norme n'est pas de servir de guide complet
pour la conception des lignes de transmission. Elle ne comprend, par exemple, aucune information relative à
la prévention des vibrations exercées sur les lignes de transmission ni aucune information relative au
dimensionnement d'un dispositif de limitation de couple. Les combinaisons d'instruments avec tracteurs à
garde au sol élevée, tels que ceux opérant dans les cultures maraîchères sur pied ou les plantations de canne
à sucre, voire les tracteurs agricoles conçus pour une garde au sol peu élevée, tels que les tracteurs utilisés
pour tondre le gazon ou entretenir le sol, et requérant un centre de gravité peu élevé, ne font pas l'objet de la
présente partie de l’ISO 5673. Elle ne s’applique pas non plus aux instruments à la conception non
symétrique par nécessité en raison de leur fonction.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence (y compris les éventuels amendements) s'applique.
ISO 500-3:2004, Tracteurs agricoles — Prises de force montées à l'arrière des types 1, 2 et 3 — Partie 3:
Dimensions principales de la prise de force et dimensions des cannelures, emplacement de la prise de force
ISO 730-1:1994, Tracteurs agricoles à roues — Attelage trois points monté à l'arrière — Partie 1: Catégories
1, 2, 3 et 4
ISO 6489-1:2001, Véhicules agricoles — Liaisons mécaniques entre véhicules remorqueurs et véhicules
remorqués — Partie 1: Dimensions des crochets d'attelage
ISO 6489-2:2002, Véhicules agricoles — Liaisons mécaniques entre véhicules remorqueurs et véhicules
remorqués — Partie 2: Spécifications relatives aux attelages de type chape de 40
© ISO 2005 – Tous droits réservés 1

---------------------- Page: 5 ----------------------
ISO 5673-2:2005(F)
ISO 6489-3:2004, Véhicules agricoles — Liaisons mécaniques entre véhicules remorqueurs et véhicules
remorqués — Partie 3: Barre d'attelage du tracteur
ISO 6489-4:2004, Véhicules agricoles — Liaisons mécaniques entre véhicules remorqueurs et véhicules
remorqués — Partie 4: Dimensions des dispositifs d'attelage de type piton
1)
ISO 24347:— , Véhicules agricoles — Liaisons mécaniques entre véhicules remorqueurs et véhicules
remorqués — Dimensions des dispositifs d'attelage de type à boule (80 mm)
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l’ISO 5673-1 s’appliquent.
4 Application et utilisation des arbres de transmission à cardans de prise de force
4.1 Modèle A
Un arbre de transmission à cardans de prise de force modèle A avec deux joints de cardan, tel que
représenté à la Figure 1, compense les variations angulaires et longitudinales des arbres reliant la prise de
force et l’arbre récepteur de la machine. Les angles égaux des courbes en W et Z garantissent une
transmission uniforme du mouvement de rotation.

Figure 1 — Arbre de transmission à cardans de prise de force — Modèle A
4.2 Modèle B
Un arbre de transmission à cardans de prise de force modèle B avec un joint de cardan homocinétique à
grand angle et un joint de cardan, tel que représenté à la Figure 2, compense les variations angulaires et
longitudinales des arbres reliant la prise de force et l’arbre récepteur de la machine. Les mouvements de
rotation sont transmis uniformément tant que le joint simple est aligné avec l’arbre de transmission ou que
l’écart angulaire entre eux est inférieur à 10°.

1) À publier.
2 © ISO 2005 – Tous droits réservés

---------------------- Page: 6 ----------------------
ISO 5673-2:
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.