SIST EN 1679-1:2000/kprA1:2010
(Amendment)Reciprocating internal combustion engines - Safety - Part 1: Compression ignition engines
Reciprocating internal combustion engines - Safety - Part 1: Compression ignition engines
2010-01-14: reactivated due to delivery of the text.
2010-01-06 EMA: Deletion following 3-year timeframe exercise.
2009-09-09 SJ: Under Alert 2 - can be deleted if no text by end December 2009.
Hubkolben-Verbrennungsmotoren - Sicherheit - Teil 1: Dieselmotoren
Moteurs alternatifs à combustion interne - Sécurité - Partie 1: Moteurs à allumage par compression
Batni stroji z notranjim zgorevanjem - Varnost - 1. del: Dizelski motorji
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1679-1:2000/kprA1:2010
01-september-2010
Batni stroji z notranjim zgorevanjem - Varnost - 1. del: Dizelski motorji
Reciprocating internal combustion engines - Safety - Part 1: Compression ignition
engines
Hubkolben-Verbrennungsmotoren - Sicherheit - Teil 1: Dieselmotoren
Moteurs alternatifs à combustion interne - Sécurité - Partie 1: Moteurs à allumage par
compression
Ta slovenski standard je istoveten z: EN 1679-1:1998/FprA1
ICS:
27.020 Motorji z notranjim Internal combustion engines
zgorevanjem
SIST EN 1679-1:2000/kprA1:2010 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1679-1:2000/kprA1:2010
---------------------- Page: 2 ----------------------
SIST EN 1679-1:2000/kprA1:2010
EUROPEAN STANDARD
FINAL DRAFT
EN 1679-1:1998
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
May 2010
ICS 27.020
English Version
Reciprocating internal combustion engines - Safety - Part 1:
Compression ignition engines
Moteurs alternatifs à combustion interne - Sécurité - Partie Hubkolben-Verbrennungsmotoren - Sicherheit - Teil 1:
1: Moteurs à allumage par compression Dieselmotoren
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 270.
This draft amendment A1, if approved, will modify the European Standard EN 1679-1:1998. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1679-1:1998/FprA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1679-1:2000/kprA1:2010
EN 1679-1:1998/FprA1:2010 (E)
Contents Page
Foreword .3
1 Modification to the Foreword .4
2 Modification to the Introduction .4
3 Modifications to Clause 1, Scope .4
4 Modifications to Clause 2, Normative references .4
5 Modification to Clause 3, Definitions .8
6 Modifications to Clause 6, Safety requirements and/or measures .8
7 Modifications to Clause 7, Operating and maintenance instructions . 11
8 Modification to Clause 9, Marking. 11
9 Modifications to ANNEX B, Bibliography . 11
10 Modification to ANNEX ZA, Relationship with EU Directives . 11
2
---------------------- Page: 4 ----------------------
SIST EN 1679-1:2000/kprA1:2010
EN 1679-1:1998/FprA1:2010 (E)
Foreword
This document (EN 1679-1:1998/FprA1:2010) has been prepared by Technical Committee CEN/TC 270
“Internal Combustion Engines”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
3
---------------------- Page: 5 ----------------------
SIST EN 1679-1:2000/kprA1:2010
EN 1679-1:1998/FprA1:2010 (E)
1 Modification to the Foreword
th
Replace the 4 paragraph with the following:
"For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.".
2 Modification to the Introduction
Replace the complete text with the following:
"This document is a type C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and hazardous events are
covered are indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.".
3 Modifications to Clause 1, Scope
th
Delete the 4 paragraph.
Add the following paragraph at the end of the Scope:
"This European Standard is not applicable to compression ignition engines which are manufactured before the
date of its publication as EN.".
4 Modifications to Clause 2, Normative references
Replace the standard paragraph with the following:
"The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.".
Update the normative references as follows:
EN Standards
Replace reference prEN 286-1:1995 with:
"EN 286-1:1998, Simple unfired pressure vessels designed to contain air or nitrogen — Part 1: Pressure
vessels for general purposes".
Delete reference EN 292-1:1991 and add:
4
---------------------- Page: 6 ----------------------
SIST EN 1679-1:2000/kprA1:2010
EN 1679-1:1998/FprA1:2010 (E)
"EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology (ISO 12100-1:2003)".
Delete reference EN 292-2: 1991 and add:
"EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles (ISO 12100-2:2003)".
Delete reference EN 294:1992 (superseded together with EN 811:1996 by EN ISO 13857:2008).
Delete reference EN 418:1992 and add:
"EN ISO 13850:2008, Safety of machinery — Emergency stop — Principles for design (ISO 13850:2006)".
Delete reference EN 563:1994 and add:
"EN ISO 13732-1:2008, Ergonomics of the thermal environment — Methods for the assessment of human
responses to contact with surfaces — Part 1: Hot surfaces (ISO 13732-1:2006)".
Replace reference EN 547-2:1996 with:
"EN 547-2:1996, Safety of machinery — Human body measurements — Part 2: Principles for determining the
dimensions required for access openings".
Delete reference prEN 811:1992 and add:
"EN ISO 13875:2008, Safety of machinery — Safety distances to prevent danger zones being reached by
upper and lower limbs (ISO 13857:2008)".
Replace reference prEN 1175-1 with:
"EN 1175-1:1998, Safety of industrial trucks — Electrical requirements — Part 1: General requirements for
battery powered trucks".
Replace reference prEN 1175-2 with:
"EN 1175-2:1998, Safety of industrial trucks — Electrical requirements — Part 2: General requirements of
internal combustion engine powered trucks".
Replace reference prEN 1175-3 with:
"EN 1175-3:1998, Safety of industrial trucks — Electrical requirements — Part 3: Specific requirements for the
electric power transmission systems of internal combustion engine powered trucks".
Replace reference prEN 1834-1:1995 with:
"EN 1834-1:2000, Reciprocating internal combustion engines — Safety requirements for design and
construction of engines for use in potentially explosive atmospheres — Part 1: Group II engines for use in
flammable gas and vapour atmospheres".
Replace reference prEN 1834-2:1996 with:
"EN 1834-2:2000, Reciprocating internal combustion engines — Safety requirements for design and
construction of engines for use in potentially explosive atmospheres — Part 2: Group I engines for use in
underground workings susceptible to firedamp and/or combustible dust".
5
---------------------- Page: 7 ----------------------
SIST EN 1679-1:2000/kprA1:2010
EN 1679-1:1998/FprA1:2010 (E)
Replace reference prEN 1834-3:1996 with:
"EN 1834-3:2000, Reciprocating internal combustion engines — Safety requirements for design and
construction of engines for use in potentially explosive atmospheres — Part 3: Group II engines for use in
flammable dust atmospheres".
Delete reference EN ISO 8178-1:1996 and add under "ISO Standards":
"ISO 8178-1:2006, Reciprocating internal combustion engines — Exhaust emission measurement — Part 1:
Test-bed measurement of gaseous and particulate exhaust emissions".
Delete reference EN ISO 8178-2:1996 and add under "ISO Standards":
"ISO 8178-2:2008, Reciprocating internal combustion engines — Exhaust emission measurement — Part 2:
Measurement of gaseous and particulate exhaust emissions at site".
Delete reference EN ISO 8178-4:1996 and add under "ISO Standards":
"ISO 8178-4:2007, Reciprocating internal combustion engines — Exhaust emission measurement — Part 4:
Steady-state test cycles for different engine applications".
Delete reference prEN ISO 8178-5:1995 and add under "ISO Standards":
"ISO 8178-5:2008, Reciprocating internal combustion engines — Exhaust emission measurement — Part 5:
Test fuels".
Delete reference prEN ISO 8178-6:1995 and add under "ISO Standards":
"ISO 8178-6:2000, Reciprocating internal combustion engines — Exhaust emission measurement — Part 6:
Report of measuring results and test".
Replace reference EN ISO 11102-1:1997 with
"EN ISO 11102-1:2009, Reciprocating internal combustion engines — Handle starting equipment — Part 1:
Safety requirements and tests (ISO 11102-1:1997)".
Replace reference EN ISO 11102-2:1997 with:
"EN ISO 11102-2:2009, Reciprocating internal combustion engines — Handle starting equipment — Part 2:
Method of testing the angle of disengagement (ISO 11102-2:1997)".
Delete reference 23411:1988 and add:
"EN ISO 3411:2007, Earth-moving machinery — Physical dimensions of operators and minimum operator
space envelope (ISO 3411:2007)".
Replace reference prEN 61310-1:1995 with:
"EN 61310-1:2008, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for
visual, acoustic and tactile signals (IEC 61310-1:2007)".
Replace reference prEN 61310-2:1994 with:
"EN 61310-2:2008, Safety of machinery — Indication, marking and actuation
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.