SIST EN 16307-6:2014
(Main)Industrial trucks - Safety requirements and verification - Part 6: Supplementary requirements for burden and personnel carriers
Industrial trucks - Safety requirements and verification - Part 6: Supplementary requirements for burden and personnel carriers
EN 16307-6 gives requirements for the types of industrial trucks specified in the scope of prEN ISO 3691-6. This standard is intended to be used in conjunction with prEN ISO 3691-6. These requirements are supplementary to those stated in prEN ISO 3691-6 with the addition of following hazards: - Noise emissions; - Vibration; - Electromagnetic compatibility (EMC); - When operating in potentially explosive atmospheres. This European standard replaces the following requirements of prEN ISO 3691-6: - Electrical requirements. This European standard defines supplementary requirements to prEN ISO 3691-6: - Brakes; - Operator's seat; - Protection from burning; - Protection against crushing, shearing and trapping; - Visibility; - Information for use (instruction handbook and marking).
Flurförderzeuge - Sicherheitstechnische Anforderungen und Verifizierung - Teil 6: Zusätzliche Anforderungen für Lasten- und Personentransportfahrzeuge
Diese Europäische Norm enthält Anforderungen an die im Anwendungsbereich von EN ISO 3691-6:2013 aufgeführten Arten von Flurförderzeugen.
Die vorliegende Norm muss in Verbindung mit EN ISO 3691-6:2013 angewendet werden. Die hier angegebenen Anforderungen gelten zusätzlich zu den in EN ISO 3691-6:2013 angegebenen Anforderungen für die folgenden zusätzlichen Gefährdungen:
- Geräuschemission;
- Vibration;
- Elektromagnetische Verträglichkeit (EMV);
- für den Einsatz in explosionsgefährdeten Bereichen.
Die vorliegende Europäische Norm ersetzt teilweise die folgenden Anforderungen von EN ISO 3691-6:2013:
- elektrische Anforderungen.
Diese Europäische Norm legt gegenüber EN ISO 3691-6:2013 zusätzliche Anforderungen fest:
- Bremsen;
- Maschinenführersitz;
- Schutz vor Verbrennung;
- Schutz gegen Quetschen, Scheren und Fangen;
- Sichtverhältnisse;
- Benutzerinformation (Bedienungsanleitung und Kennzeichnung).
Im (informativen) Anhang A ist eine Liste der signifikanten Gefährdungen enthalten, die in dieser Norm behandelt werden.
Chariots de manutention - Exigences de sécurité et vérification - Partie 6: Exigences supplémentaires pour les chariots porte-charge et chariots porte-personne
La présente Norme européenne donne des prescriptions pour les types de chariots de manutention spécifiés dans le domaine d’application de l’EN ISO 3691-6:2013.
La présente Norme européenne est destinée à être utilisée en conjonction avec l’EN ISO 3691-6:2013. Ces prescriptions sont complémentaires à celles énoncées dans l’EN ISO 3691-6:2013 avec l’ajout des phénomènes dangereux suivants :
- Émissions sonores ;
- Vibrations ;
- Compatibilité électromagnétique (CEM) ;
- Fonctionnement en atmosphères potentiellement explosibles.
La présente Norme européenne remplace les prescriptions suivantes de l’EN ISO 3691-6:2013 :
- Prescriptions électriques.
La présente Norme européenne définit des prescriptions supplémentaires à l’EN ISO 3691-6:2013 :
- Freins ;
- Siège du conducteur ;
- Protection contre les brûlures ;
- Protection contre l’écrasement, le cisaillement et l’emprisonnement ;
- Visibilité ;
- Informations pour l’utilisation (notice d’instruction et marquage).
L’Annexe A (informative) contient la liste des phénomènes dangereux significatifs couverts par la présente Norme européenne.
Vozila za talni transport - Varnostne zahteve in preverjanje - 6. del: Dodatne zahteve za tovorne in osebne vozičke
Ta standard EN 16307-6 podaja zahteve za vrste vozil za talni transport, ki so navedene v okviru standarda prEN ISO 3691-6. Ta standard je treba uporabljati v povezavi s standardom prEN ISO 3691-6. Te zahteve dopolnjujejo zahteve iz standarda prEN ISO 3691-6 in dodatno obravnavajo naslednja tveganja: – emisije hrupa; – vibracije; – elektromagnetno združljivost (EMC); – pri obratovanju v potencialno eksplozivnih atmosferah. Ta evropski standard nadomešča naslednje zahteve standarda prEN ISO 3691-6: – električne zahteve. Ta evropski standard določa dodatne zahteve za standard prEN ISO 3691-6: – zavore; – sedež upravljavca; – zaščito pred opeklinami; – zaščito pred zdrobitvijo, urezninami in ukleščenjem; – vidljivost; – informacije za uporabo (priročnik za uporabo in označevanje).
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flurförderzeuge - Sicherheitstechnische Anforderungen und Verifizierung - Teil 6: Zusätzliche Anforderungen für Lasten- und PersonentransportfahrzeugeChariots de manutention - Exigences de sécurité et vérification - Partie 6: Exigences supplémentaires pour les chariots porte-charge et chariots porte-personneIndustrial trucks - Safety requirements and verification - Part 6: Supplementary requirements for burden and personnel carriers53.060Industrijski tovornjakiIndustrial trucksICS:Ta slovenski standard je istoveten z:EN 16307-6:2014SIST EN 16307-6:2014en,fr,de01-junij-2014SIST EN 16307-6:2014SLOVENSKI
STANDARD
SIST EN 16307-6:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16307-6
April 2014 ICS 53.060 English Version
Industrial trucks - Safety requirements and verification - Part 6: Supplementary requirements for burden and personnel carriers Chariots de manutention - Exigences de sécurité et vérification - Partie 6 : Exigences supplémentaires pour les chariots porte-charge et chariots porte-personne
Flurförderzeuge - Sicherheitstechnische Anforderungen und Verifizierung - Teil 6: Zusätzliche Anforderungen für Lasten-und Personentransportfahrzeuge This European Standard was approved by CEN on 1 December 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16307-6:2014 ESIST EN 16307-6:2014
EN 16307-6:2014 (E) 2 Contents Page Foreword .3 0 Introduction .4 0.1 General .4 0.2 Assessment of hazards .4 1 Scope .5 2 Normative references .5 3 Terms and definitions .6 4 Safety requirements and/or protective measures .6 4.1 General .6 4.2 Electrical requirements .6 4.3 Brakes .6 4.4 Operator's seat .6 4.5 Protection from burning .6 4.6 Protection against crushing, shearing and trapping .7 4.7 Visibility .7 4.8 Reduction of noise by design .7 4.8.1 General .7 4.8.2 Main source of noise .7 4.8.3 Measures to reduce noise at the operator's position .8 4.8.4 Determination of noise emission values .8 4.9 Vibration .8 4.10 Electromagnetic compatibility (EMC) .8 4.11 Operation in potentially explosive atmospheres .8 5 Verification of safety requirements and/or protective measures .8 6 Information for use .8 6.1 Instruction handbook(s) .8 6.1.1 Carrier/attachments .8 6.1.2 Operation of the carrier .9 6.2 Marking .9 6.2.1 Information plates .9 Annex A (informative)
List of significant hazards . 10 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EC Directive 2006/42/EC . 12 Bibliography . 13
SIST EN 16307-6:2014
EN 16307-6:2014 (E) 3 Foreword This document (EN 16307-6:2014) has been prepared by Technical Committee CEN/TC 150 “Industrial Trucks - Safety”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2014, and conflicting national standards shall be withdrawn at the latest by October 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive 2006/42/EC, see informative Annex ZA, which is an integral part of this document. This document is based on ISO/TS 3691-7, Industrial trucks — Safety requirements and verification — Part 7: Regional requirements for countries within the European Community, and is limited to self-propelled industrial trucks. EN 16307 consists of the following parts, under the general title Industrial trucks — Safety requirements and verification: — Part 1: Supplementary requirements for self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks; — Part 2: Supplementary requirements for self-propelled variable-reach trucks; — Part 3: Supplementary requirements for trucks with elevating operator position and trucks specifically designed to travel with elevated loads (additional requirements to EN 16307-1); — Part 4: Supplementary requirements for driverless industrial trucks and their systems; — Part 5: Supplementary requirements for pedestrian-propelled trucks; — Part 6: Supplementary requirements for burden and personnel carriers. This document is to be used with EN ISO 3691-6:2013, Industrial trucks — Safety requirements and verification – Part 6: Burden and personnel carriers (ISO 3691-6:2013). According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 16307-6:2014
EN 16307-6:2014 (E) 4 0 Introduction 0.1 General This document is a type-C standard as stated in EN ISO 12100:2010. The machines concerned and the extent to which hazards, hazardous situations or hazardous events are covered are indicated in the scope of this document (Clause 1). When requirements of this type-C standard are different from those which are stated in type-A or B standards, the requirements of this type-C standard take precedence over the requirements of the other standards for machines that have been designed and built according to the requirements of this type-C standard. The EN 16307 series of standards covers safety requirements and their verification for industrial trucks as defined in ISO 5053 that are not covered exhaustively by EN ISO 3691 series. 0.2 Assessment of hazards The product needs to be designed in such a way that it is fit for its purpose or function and can be adjusted and maintained without putting persons at risk when used under the conditions foreseen by the manufacturer. In order to properly design a product and to cover all specific safety requirements, the manufacturer will have to identify the hazards that apply to his product and carry out a risk assessment. The manufacturer will then need to design and construct the product taking this assessment into account. The aim of this procedure is to eliminate the risk of accidents throughout the foreseeable lifetime of the machinery, including the phases of assembling and dismantling where risks of accidents could also arise from foreseeable abnormal situations. In selecting the most appropriate methods, the manufacturer will need to apply the following principles, in the order given here: a) eliminate or reduce risks as far as possible by design (inherently safe machinery design and construction); b) take the necessary protective measures in relation to risks that cannot be eliminated by design; c) inform users of any shortcoming of the protective measures adopted; d) indicate whether any particular training is required; e) specify any need to provide personal protection equipment; f) refer to the appropriate user's document for proper operating instructions. Industrial trucks need to be designed to prevent foreseeable misuse wherever possible, if such would engender risk. In other cases, the instructions will need to draw the user's attention to ways shown by experience in which the machinery ought not be used. This part of EN 16307 does not repeat all the technical rules which are sta
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.