kSIST FprEN 1790:2011
(Main)Road marking materials - Preformed road markings
Road marking materials - Preformed road markings
The construction products covered and specified on this European Standard are white and yellow, removable or non-removable, preformed road marking materials, under the form of tape, cold plastic, thermoplastics with or without drop-on materials, to be used for permanent and/or temporary road markings in circulation areas. Other products and colours intended for road markings are not covered in this European Standard
This document gives also specifications for the evaluation of conformity for white and yellow, removable or non-removable, preformed road materials under the form of tape, cold plastic, thermoplastics with or without drop-on materials to be used for permanent and/or temporary road markings in circulation areas including type testing and factory production control.
This European Standard also includes an Annex ZA for tapes, preformed cold plastic road marking and thermoplastic road marking without drop-on materials with the clauses addressing the provisions of the EU Construction Product Directive for permanent road marking.
For preformed Thermoplastic road marking with drop-on materials, Annex ZA of FprEN 1871:2011 applies.
Straßenmarkierungsmaterialien - Vorgefertigte Markierungen
Die von dieser Europäischen Norm abgedeckten und festgelegten Bauprodukte sind weiß oder gelbe, demarkierbare oder nicht demarkierbare vorgefertigte Straßenmarkierungsmaterialien in Form von Markierungsfolien, Kaltplastikmarkierungen oder Heißplastikmarkierungen mit oder ohne Nachstreumittel, die als dauerhafte oder vorübergehende Markierungen auf Verkehrsflächen verwendet werden. Andere Produkte oder Farben, die für Straßenmarkierungen verwendet werden, werden in dieser Europäischen Norm nicht behandelt.
Diese Europäische Norm enthält auch Festlegungen für die Bewertung der Konformität von weißen oder gelben, demarkierbaren oder nicht demarkierbaren vorgefertigten Straßenmarkierungsmaterialien in Form von Markierungsfolien, Kaltplastikmarkierungen oder Heißplastikmarkierungen mit oder ohne Nachstreumittel, die als dauerhafte oder vorübergehende Markierungen auf Verkehrsflächen verwendet werden, einschließlich der Erstprüfung und der werkseigenen Produktionskontrolle.
Ferner enthält diese Europäische Norm einen Anhang ZA für Markierungsfolien, vorgefertigte Kaltplastikmarkierungen und Heißplastikmarkierungen ohne Nachstreumittel mit Abschnitten, die die Bestimmungen der EU-Bauproduktenrichtlinie für dauerhafte Straßenmarkierungsmaterialien betreffen.
Für vorgefertigte Heißplastikmarkierungen mit Nachstreumitteln gilt der Anhang ZA von FprEN 1871:2011.
Produits de marquage routier - Marquages routiers préformés
Les produits de construction couverts et spécifiés dans la présente Norme européenne sont les produits de marquage routier préfabriqués blancs et jaunes, enlevables ou non, sous forme de bandes préfabriquées multicouches, d’enduits à froid et d’enduits à chaud avec ou sans produits de saupoudrage, destinés au marquage routier permanent et/ou temporaire dans les zones de circulation. Les autres produits et couleurs destinés au marquage routier ne sont pas couverts dans la présente Norme européenne.
Le présent document fournit également des spécifications pour l’évaluation de la conformité des produits de marquage routier préfabriqués blancs et jaunes, enlevables ou non, sous forme de bandes préfabriquées multicouches, d’enduits à froid et d’enduits à chaud avec ou sans produits de saupoudrage, destinés au marquage routier permanent et/ou temporaire dans les zones de circulation, y compris les essais de type et le contrôle de la production en usine.
La présente Norme européenne comprend également une Annexe ZA pour les bandes préfabriquées multicouches, les bandes préfabriquées en enduit à froid et les bandes préfabriquées en enduit à chaud sans produits de saupoudrage, avec les articles concernant les dispositions de la Directive UE Produits de Construction pour le marquage routier permanent.
Pour les bandes préfabriquées en enduit à chaud avec produits de saupoudrage, l’Annexe ZA du FprEN 1871:2011 s’applique.
Materiali za označevanje vozišča - Predoblikovane oznake
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Straßenmarkierungsmaterialien - Vorgefertigte MarkierungenRoad marking materials - Preformed road markings93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:FprEN 1790kSIST FprEN 1790:2011en,fr,de01-april-2011kSIST FprEN 1790:2011SLOVENSKI
STANDARD
kSIST FprEN 1790:2011
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 1790
February 2011 ICS 93.080.20 Will supersede EN 1790:1998English Version
Road marking materials - Preformed road markings
Straßenmarkierungsmaterialien - Vorgefertigte Markierungen This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 226.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN 1790:2011: EkSIST FprEN 1790:2011
FprEN 1790:2011 (E) 2 Contents Page Foreword . 3Introduction . 41Scope . 52Normative references . 53Terms and definitions . 54Requirements . 75Test methods . 96Evaluation of conformity . 117Marking and labelling . 18Annex A (normative)
Identification of preformed road marking materials . 19Annex B (normative)
Test method for Ash content . 21Annex C (normative)
Thermogravimetric analysis (TGA) . 23Annex D (normative)
FT-IR spectroscopy of the TGA residue . 25Annex E (normative)
Test method for ATR FT-IR spectroscopy of the adhesive layer . 26Annex F (normative)
Preformed self-adhesive road marking – Test method for determination of mass per unit area of the adhesive . 27Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Directive . 29Bibliography . 39 kSIST FprEN 1790:2011
FprEN 1790:2011 (E) 3 Foreword This document (FprEN 1790:2011) has been prepared by Technical Committee CEN/TC 226 “Road equipment”, the secretariat of which is held by AFNOR. This document is currently submitted to the UAP. This document will supersede EN 1790:1998. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationship with the Construction Product Directive (89/106/EEC), see informative Annex ZA, which is an integral part of this document. The Annexes A, B, C, D, E and F of this European Standard are normative. This European Standard belongs to the following package of inter-related European Standards:
FprEN 1790, Road marking materials
Preformed road markings, FprEN 1824, Road marking materials
Road trials, FprEN 1871, Road marking materials
Physical properties, FprEN 12802, Road marking materials
Laboratory methods and identification, FprEN 13197, Road marking materials
Turntable wear simulators, FprEN 13212, Road marking materials
Requirements for factory production control, FprEN 13459, Road marking materials
Sampling and testing.
kSIST FprEN 1790:2011
FprEN 1790:2011 (E) 4 Introduction A particular category of road marking materials, used for horizontal signalization, are preformed, i.e. manufactured products in sheet form, ready for use on the road. They can be applied by means of adhesives, pressure or heat, with or without the use of a primer. Preformed road marking materials can be linear, in pieces of a certain length or in rolls. They can also be cut out in the form of symbols or signs or parts of them, making it possible to assemble them on the road to achieve the desired shape. Preformed road marking materials can be designed for use as permanent or temporary road markings. In both cases they can be applied with a view to later removal and therefore the specific property of "removability" can be required. Preformed road marking products are defined as Tape, preformed Cold Plastic road marking or preformed Thermoplastic road marking with or without drop-on materials. Except for Thermoplastic road markings with drop-on materials, all the other type of products are fully finished during manufacturing and do not change significantly their properties during application. They are completely covered by this standard. Thermoplastic road markings with drop-on materials need the addition of drop-on materials during application on the road and therefore they are in some way similar to thermoplastic products covered by FprEN 1871. This standard provides all the relevant information and cross references to FprEN 1871 in order to cover this kind of products. kSIST FprEN 1790:2011
FprEN 1790:2011 (E) 5 1 Scope The construction products covered and specified on this European Standard are white and yellow, removable or non-removable, preformed road marking materials, under the form of tape, cold plastic, thermoplastics with or without drop-on materials, to be used for permanent and/or temporary road markings in circulation areas. Other products and colours intended for road markings are not covered in this European Standard
This document gives also specifications for the evaluation of conformity for white and yellow, removable or non-removable, preformed road materials under the form of tape, cold plastic, thermoplastics with or without drop-on materials to be used for permanent and/or temporary road markings in circulation areas including type testing and factory production control. This European Standard also includes an Annex ZA for tapes, preformed cold plastic road marking and thermoplastic road marking without drop-on materials with the clauses addressing the provisions of the EU Construction Product Directive for permanent road marking. For preformed Thermoplastic road marking with drop-on materials, Annex ZA of FprEN 1871:2011 applies. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1436:2007+A1:2008, Road marking materials Road marking performance for road users
FprEN 1824:2010, Road marking materials Road trials FprEN 1871:2011, Road marking materials Paint, thermoplastic and cold plastic materials Specifications FprEN 12802, Road marking materials Laboratory methods and identification FprEN 13197:2010, Road marking materials Turntable wear simulators FprEN 13459, Road marking materials Sampling and testing EN ISO 4892-3, Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps (ISO 4892-3:2006) EN ISO 11358, Plastics Thermogravimetry (TG) of polymers General principles (ISO 11358:1997) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 preformed road marking factory produced road marking system (or product), in sheet or roll form, capable of being applied to the substrate with adhesive, primer, pressure, heat or a combination of them 3.1.1
tape preformed multilayer road marking, capable of adapting itself to the texture of the substrate, which may be precoated with pressure-sensitive adhesive, capable of being stuck to the substrate without heating the material, kSIST FprEN 1790:2011
FprEN 1790:2011 (E) 6 while the photometric, colorimetric and skid resistance characteristics are not significantly modified during application 3.1.2 preformed cold plastic road marking preformed road marking made of cold plastic marking material as defined in FprEN 1871:2011, applied to the substrate by means of an adhesive, while the photometric, colorimetric and skid resistance characteristics are not significantly modified during application 3.1.3 preformed thermoplastic road marking without drop-on materials “pre-beaded” preformed road marking made of thermoplastic marking material as defined in FprEN 1871:2011, applied to the substrate by heating the material at melting temperature and without addition of any retroreflective and/or anti-skid materials during application 3.1.4 preformed thermoplastic road marking with drop-on materials preformed road marking made of thermoplastic road marking material as defined in FprEN 1871:2011, applied to the substrate by heating the material at melting temperature and with addition of retroreflective and/or anti-skid materials during application 3.2 removability characteristic of a preformed road marking capable of being removed, intact or in large pieces, without leaving permanent marks that could confuse the road user during different weather conditions 3.3 adhesive substance which is used to bond the preformed road marking to the substrate and the application of which may require heating 3.4 base road marking material according to 3.4 of FprEN 1871:2011, paint, a thermoplastic or acold plastic with a unique identification, which may, or may not, include premix glass beads. This definition is relevant only for preformed thermoplastic road marking with drop-on materials as defined in 3.1.4 3.5 road marking assembly according to 3.5 of FprEN 1871:2011, base road marking material together the precise application instructions including the identification of the manufacturer, dosages, types and proportions of drop-on materials needed to build up the applied road markings, every change to which is a new assembly and is identified with the name of the base road marking material followed by the word assembly and a correlative number (e.g. Thermo AX – Assembly 1; Thermo AX – assembly 2, etc). This definition is relevant only for preformed thermoplastic road marking with drop-on materials as defined in 3.1.4 3.6 structured road marking products road marking product without areas of regular dimensions and tap surfaces, which has flat areas of a maximum width of 75.7 mm a maximum length of 125 mm at the top of the structure. The areas may be crossed by gaps that take up minimum 25% of the total surface area and have widths of minimum 5 mm. The areas may have ridges or edges of blocks with a height of minimum 1,2 mm. 3.7 non structured road marking products road marking product with areas of regular dimensions and tap surfaces, which has flat areas of a minimum width of 75.7 mm a minimum length of 125 mm at the top of the structure. The areas may be crossed by gaps that take up maximum 25% of the total surface area and have widths of maximum 5 mm. The areas may have ridges or edges of blocks with a height of maximum 1,2 mm. kSIST FprEN 1790:2011
FprEN 1790:2011 (E) 7 NOTE
Additional materials to those described in 3.1 to 3.3 can include, if recommended by the manufacturer, primers which are liquid products which may contain solids and liquid additives suspended in an organic solvent or in water. The solids comprise inorganic and/or organic fillers, pigments and additives. The content of volatile organic solvents is not limited.
Primers are used to precoat road surfaces before the road marking system is applied. They improve the adhesion of the road marking and protect against disintegration, discolouring, etc. caused by incompatible compounds in the road surface. 4 Requirements 4.1 Tape, Preformed Cold Plastic Road Marking and Preformed Thermoplastic Road Marking without drop-on Materials 4.1.1 General The requirements are meant as characteristics of the materials as fully finished products. They are therefore intended as laboratory requirements. 4.1.2 Reflection in daylight or under road lighting (day-time visibility)
It represents the brightness of a road marking as seen by driver’s vehicles in typical or average daylight or under road lighting. It shall be measured either by the coefficient of luminance under diffuse illumination (Qd), expressed in mcd·m-2·lx-1 or by the luminance factor (). a) When luminance coefficient under diffuse illumination Qd is measured, the preformed road marking material is tested in accordance to 5.2.1 a) and shall comply with classes Q1 to Q5 of Table 1 of EN 1436:2007+A1:2008
b) When luminance factor
is measured, the preformed road marking material is tested in accordance to 5.2.1 b), and shall comply with Table 1: Table 1 Classes of luminance factor ββββ in dry conditions Type and colour Class (as defined in EN 1436:2007+A1:2008) Luminance factor β Permanent
White and yellow
White
Yellow
B0 B5 B3
No value requested
≥ 0,60 ≥ 0,40 Temporary
White and yellow
White
Yellow
B0 B6 B3
No value requested
≥ 0,70 ≥ 0,40
4.1.3 Retroreflection under vehicle headlamp illumination (night-time visibility).
It represents the brightness of a road marking as seen by driver’s vehicles under the illumination by the driver’s own headlamp. The result is expressed by the coefficient of retroreflected luminance in mcd·m-2·lx-1. The coefficient of retroreflected luminance on dry conditions changes during wetness or during rain. Retroreflected luminance during wetness or during rain only applies for road markings type II. a) When preformed road marking material is tested on dry conditions, in accordance to 5.2.2 a), the coefficient of the retroreflected luminance RL shall comply with classes R1 to R5 of Table 3 of EN 1436:2007+A1:2008. b) When preformed road marking material is tested during wetness in accordance to 5.2.2 b), the coefficient of the retroreflected luminance RL shall comply with classes RW1 to RW6 of Table 4 of EN 1436:2007+A1:2008. kSIST FprEN 1790:2011
FprEN 1790:2011 (E) 8 c) When preformed road marking material is tested during rain in accordance to 5.2.2 c), the coefficient of the retroreflected luminance RL shall comply with classes RR1 to RR6 of Table 5 of EN 1436:2007+A1:2008. 4.1.4 Colour It shall be defined by means of (x,y) chromaticity co-ordinates. When a white preformed road marking is tested in accordance to 5.2.3, the x, y chromaticity co-ordinates shall lie within the region defined by the corner points given in Table 6 of EN 1436:2007+A1:2008 for white road markings. When a yellow preformed road marking is tested in accordance to 5.2.3, the x, y chromaticity co-ordinates shall lie within the region Y2 defined by the corner points given in Table 6 of EN 1436:2007+A1:2008 for yellow road markings. 4.1.5 Skid resistance
It represents the energy loss caused by the friction of a rubber slider over a specified length of a road marking surface in wet conditions. The result is expressed in SRT (Skid Resistance Tester) units. Measured on samples in the laboratory according to 5.2.4, the skid resistance of preformed materials shall be in accordance with classes S1 to S5 of Table 7 of EN 1436:2007+A1:2008. In the case of road trial with studded tyres class P0 applies. 4.1.6 Removability
Removability, as defined in 3.2, shall be tested in order to evaluate if the preformed road marking material is entirely removable without leaving permanent marks that could confuse the road user during the different weather conditions. The removability of preformed road markings cannot be determined in the laboratory and shall therefore be tested on the road, in accordance with 5.2.5. 4.1.7 Resistance to UV exposure
UV resistance shall be checked in accordance with 5.2.6. The chromaticity co-ordinates of preformed materials after UV exposure shall comply with the region for white road markings of Table 6 and with region Y2 for yellow road markings of Table 6 in EN 1436:2007+A1:2008, respectively for white and yellow preformed road marking. The preformed materials shall be classified in accordance with Table 2, where ∆β is the difference between the luminance factor before and after UV exposure. Table 2 Classes of UV resistance
Colour Class ∆β White and yellow UV0 No value requested White and yellow UV2 ≤ 0,10
4.2 Preformed thermoplastic road marking with drop-on materials Requirements for these products are defined in 4.2.2.2 of FprEN 1871:2011 (Test before heat stability for base road marking materials) and in 4.3 of FprEN 1871:2011 (Requirements for road marking assemblies). Test methods are defined in 5.3. kSIST FprEN 1790:2011
FprEN 1790:2011 (E) 9 4.3 Durability
4.3.1 General Durability represents the capability of the preformed road marking material to achieve a certain level of performance for each characteristic after being submitted to road trials and/or wear simulator. The information corresponding to the durability shall be completed with the specific test conditions.
4.3.2 Durability of retroreflection, chromaticity co-ordinates, luminance factor, Qd and skid resistance on road trials When a road marking product to be used for permanent road marking is tested according to 5.4.1, the results shall comply, at least, with roll-over class P1 of Table 3 of FprEN 1824:2010. In the case of road trial with studded tyres class P0 applies. When a road marking product to be used for temporary road marking is tested according to 5.4.1, the results shall comply with roll-over classes T0; T1 or T2 of Table 3 of FprEN 1824:2010. For the requirements of the road marking product specified in 4.1 and 4.2 , the results are expressed in terms of a class (with the exception of the colour for which pass/fail criteria is used) for the corresponding roll-over class (P) and accompanied by roughness class (RG), climatic class (C) and studded tyres (Y/N). 4.3.3 Durability of retroreflection, chromaticity co-ordinates, luminance factor, Qd and skid resistance on turntable (wear simulator) When a road marking product to be used for permanent road marking is tested according to 5.4.2, the results shall comply, at least, with traffic class P4 of Table 4 of FprEN 13197:2010.
When a road marking product to be used for temporary road marking is tested according to 5.4.2, the results shall comply, at least, with traffic class P1 of Table 4 of FprEN 13197:2010. For the requirements of the road marking product specified in 4.1 and 4.2 , the results are expressed in terms of a class (with the exception of the colour for which pass/fail criteria is used) for the corresponding roll-over class (P) and accompanied by roughness class (RG). 5 Test methods 5.1 General If not specified in the relevant test method, samples representative of each component of the material shall be taken from storage in accordance with FprEN 13459. Smaller representative samples, of sufficient quantity to carry out all the tests required, could be taken from the larger samples. 5.1.1 Preparation of samples of Tape, Preformed Cold Plastic Road Marking and Preformed Thermoplastics Road Marking without drop-on Materials For preformed materials cut in symbols, legends or other special shapes, where lengths of at least 1 m cannot be sampled, an equivalent area of at least 0.75 m², with a minimum width of 0,15 m and a length suitable for the tests mentioned in 5.2 shall be sampled. 5.1.2 Preparation of samples of Preformed Thermoplastics Road Marking with drop-on Materials If not specified in the relevant test method, sampling shall be made according to FprEN 13459. kSIST FprEN 1790:2011
FprEN 1790:2011 (E) 10 5.2 Test methods for Tape, Preformed Cold Plastic Road Marking and Preformed Thermoplastics Road Marking without drop-on Materials The requirements of 4.1 apply to the products as they leave the manufacturing site and are therefore intended as laboratory requirements. NOTE These parameters are not to be confused with the initial measurements, applied for durability purpose, which are carried out in accordance with Table 4 of FprEN 1824:2010 for initial measurements column or after 10 000 wheel passages according to FprEN 13197:2010. They indicate the performances of the road marking material measured after a short period following subsequent to its application.
5.2.1 Reflection in daylight or under road lighting (day-time visibility): it may be measured either by: a) the coefficient of luminance under diffuse illumination (Qd), expressed in mcd·m-2·lx-1 according to Annex A of EN 1436:2007+A1:2008 or b) by the luminance factor (), according to Annex C of EN 1436:2007+A1:2008. 5.2.2 Coefficient of retroreflected luminance (RL): it can be measured in different conditions as follows: a) coefficient of retroreflected luminance in dry conditions (R), in accordance with Annex B of EN 1436:2007+A1:2008; b) coefficient of retroreflected luminance with wetness (RW) in accordance with Annex B of EN 1436:2007+A1:2008; c) coefficient of retroreflected luminance during rain (RR) in accordance with Annex B of EN 1436:2007+A1:2008. 5.2.3 Colour. It shall be tested in accordance with Annex C of EN 1436:2007+A1:2008. 5.2.4 Skid resistance. It shall be tested in accordance with Annex D of EN 1436:2007+A1:2008. 5.2.5 Removability. The removability of preformed road markings cannot be determined in the laboratory and shall therefore be tested on the road, in accordance with Annex F of FprEN 1824:2010. 5.2.6 Resistance to UV exposure. The samples shall be tested in accordance with EN ISO 4892-3 for 168 h under lamp type II (UVB - 313) in cycles of 8 h of radiation at 60 °C ± 2 °C and 4 h of condensation at 50 °C ± 2 °C. 5.3 Test method for Preformed Thermoplastics Road Marking with drop-on Materials For these products, general provisions in 5.1 and methods defined in 5.2.2.2 (base road marking materials) and 5.3 (road marking assembly) of FprEN 1871:2011 apply. kSIST FprEN 1790:2011
FprEN 1790:2011 (E) 11 5.4 Durability 5.4.1 Durability of retroreflection, chromaticity co-ordinates, luminance factor, Qd and skid resistance on road trials It shall be tested in accordance to FprEN 1824. Testing conditions shall be reported as in Clause 8 of FprEN 1824:2010 for the required roll-over classes (P). 5.4.2 Durability of retroreflection, chromaticity co-ordinates, luminance factor, Qd and skid resistance on turntable (wear simulator) It shall be tested in accordance to FprEN 13197. Testing conditions shall be reported as in Clause 9 of FprEN 13197:2010 for the required traffic classes (P). 6 Evaluation of conformity 6.1 General The compliance of preformed road marking materials to the requirements of this standard and with the stated values (including classes) shall be demonstrated by: initial type testing and type testing, factory production control by the manufacturer, including product assessment. The manufacturer shall always retain the overall control and shall have the necessary means to take responsibility for the product. 6.2 Initial type testing and Type Testing 6.2.1 General Initial type testing and type testing shall be performed to demonstrate compliance with this European standard, All essential characteristics for which the manufacturer declares performances are subject to Initial Type Testing. In addition, the need to perform Type Tests applies to all other characteristics included in a standard when the manufacturer claims compliance, unless the standard gives provisions (e.g. use of previously existing data, CWFT and conventionally accepted performance) for declaring performances without performing tests. Tests previously performed in accordance with the provisions of this standard, may be taken into account provided that they were made to the same or a more rigorous test method, under the same system of attestation of conformity on the same product or products of similar design, construction and functionality, such that the results are applicable to the product in question. NOTE 1 Same system of attestation of conformity means testing by an independent third party under the responsibility of a product certification body. For the purposes of testing, the manufacturer's products may be grouped into families, where it is considered that the results for one or more characteristics from any one product within the family are representative for that same characteristics for all products within that same family (a product may be in different families for different characteristics).
NOTE 2 Products may be in different families for different characteristics. NOTE 3 Reference to the test method standards should be made to allow the selection of a suitable representative sample. kSIST FprEN 1790:2011
FprEN 1790:2011 (E) 12 Therefore Type Tests or Initial Type Testing shall be performed for all characteristics included in the standard for which the manufacturer declares performances, including that Identification is performed as in Annex A for Tape, Preformed Cold Plastic road marking and Preformed Thermoplastic road marking without drop-on materials and performed as in FprEN 12802 for Preformed Thermoplastic road marking with
drop-on materials: at the beginning of the production of a new or modified preformed road marking materials,
at the beginning of a new or modified method of production (where this may affect the stated properties); or they shall be repeated for the appropriate characteristic(s), whenever a change occurs in the preformed road marking materials, in the raw material or in the supplier of the components, or in the production process (subject to the definition of a family), which would affect significantly one or more of the characteristics. Where components are used whose characteristics have already been determined, by the component manufacturer, on the basis of compliance with other product standards, these characteristics need not be re-assessed. The specifications of these components shall be documented, as shall be included in the inspection scheme for ensuring their compliance. Preformed road marking materials marked in accordance with appropriate harmonised European specifications may be presumed to have the performances stated with the that marking, although this does not replace the responsibility of the preformed road marking materials designer to ensure that the preformed road marking materials as a whole assembly is correctly designed and its components have the necessary performance values to meet the design. 6.2.2 Test samples, testing and compliance criteria The number of samples of Tape, Preformed Cold Plastic road marking and Preformed Thermoplastic road marking without drop-on materials to be tested/assessed for Initial Type testing and Type Testing shall be in accordance with Table 3. Table 3 — Number of samples to be tested and compliance criteria Characteristic Requirement and Compliance criteria Assessment method No. of samples Essential characteristics Night-time visibility Retroreflection under headlamp illumination
Coefficient of retroreflected luminance RL on dry 4.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.