Metallic powders - Determination of flow rate by means of a calibrated funnel (Gustavsson flowmeter) (ISO 13517:2020)

EN-ISO 13517 specifies a method for determining the flow rate of metallic powders, including powders for hardmetals and mixes of metallic powders and organic additives such as lubricants, by means of a calibrated funnel (Gustavsson flowmeter).The method is applicable only to powders which flow freely through the specified test orifice.

Metallpulver - Ermittlung der Durchflussrate mit Hilfe eines kalibrierten Trichters (Gustavsson flowmeter) (ISO 13517:2020)

Dieses Dokument legt ein Verfahren zur Ermittlung der Durchflussrate für Metallpulver einschließlich Hartmetallpulver und Gemische aus Metallpulvern mit organischen Zusatzstoffen, z. B. Schmiermitteln, mit Hilfe eines kalibrierten Trichters (Gustavsson Flowmeter) fest.
Dieses Verfahren ist nur auf Pulver anwendbar, die frei durch die festgelegte Ausflussöffnung des Prüftrichters fließen.

Poudres métalliques - Détermination du temps d'écoulement au moyen d'un entonnoir calibré (cône d'écoulement de Gustavsson) (ISO 13517:2020)

Le présent document spécifie une méthode visant à déterminer le temps d'écoulement des poudres métalliques, y compris les poudres pour métaux-durs et les mélanges de poudres métalliques et d'additifs organiques tels que les lubrifiants, au moyen d'un entonnoir calibré (cône d'écoulement de Gustavsson).
Cette méthode s'applique uniquement aux poudres qui s'écoulent librement par l'orifice d'essai spécifié.

Kovinski praški - Ugotavljanje hitrosti pretoka z uporabo kalibriranega lija (merilnik pretoka po Gustavssonu) (ISO 13517:2020)

General Information

Status
Published
Public Enquiry End Date
31-Jul-2019
Publication Date
26-May-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-May-2020
Due Date
26-Jul-2020
Completion Date
27-May-2020

Relations

Buy Standard

Standard
SIST EN ISO 13517:2020
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 13517:2020
01-julij-2020
Nadomešča:
SIST EN ISO 13517:2014
Kovinski praški - Ugotavljanje hitrosti pretoka z uporabo kalibriranega lija
(merilnik pretoka po Gustavssonu) (ISO 13517:2020)
Metallic powders - Determination of flow rate by means of a calibrated funnel
(Gustavsson flowmeter) (ISO 13517:2020)

Metallpulver - Ermittlung der Durchflussrate mit Hilfe eines kalibrierten Trichters

(Gustavsson flowmeter) (ISO 13517:2020)

Poudres métalliques - Détermination du temps d'écoulement au moyen d'un entonnoir

calibré (cône d'écoulement de Gustavsson) (ISO 13517:2020)
Ta slovenski standard je istoveten z: EN ISO 13517:2020
ICS:
77.160 Metalurgija prahov Powder metallurgy
SIST EN ISO 13517:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 13517:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 13517:2020
EN ISO 13517
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2020
EUROPÄISCHE NORM
ICS 77.160 Supersedes EN ISO 13517:2013
English Version
Metallic powders - Determination of flow rate by means of
a calibrated funnel (Gustavsson flowmeter) (ISO
13517:2020)

Poudres métalliques - Détermination du temps Metallpulver - Ermittlung der Durchflussrate mit Hilfe

d'écoulement au moyen d'un entonnoir calibré (cône eines kalibrierten Trichters (Gustavsson flowmeter)

d'écoulement de Gustavsson) (ISO 13517:2020) (ISO 13517:2020)
This European Standard was approved by CEN on 1 May 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13517:2020 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13517:2020
EN ISO 13517:2020 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 13517:2020
EN ISO 13517:2020 (E)
European foreword

This document (EN ISO 13517:2020) has been prepared by Technical Committee ISO/TC 119 "Powder

metallurgy" in collaboration with CCMC.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by November 2020, and conflicting national standards

shall be withdrawn at the latest by November 2020.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN ISO 13517:2013.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of

North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

United Kingdom.
Endorsement notice

The text of ISO 13517:2020 has been approved by CEN as EN ISO 13517:2020 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 13517:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 13517:2020
INTERNATIONAL ISO
STANDARD 13517
Second edition
2020-04
Metallic powders — Determination
of flow rate by means of a calibrated
funnel (Gustavsson flowmeter)
Poudres métalliques — Détermination du temps d'écoulement au
moyen d'un entonnoir calibré (cône d'écoulement de Gustavsson)
Reference number
ISO 13517:2020(E)
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 13517:2020
ISO 13517:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 13517:2020
ISO 13517:2020(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 1

5 Apparatus ..................................................................................................................................................................................................................... 1

6 Calibration of the funnel............................................................................................................................................................................... 3

6.1 Calibration by the manufacturer of the funnel ............................................................................................................ 3

6.2 Calibration by the user of the funnel.................................................................................................................................... 3

7 Sampling ........................................................................................................................................................................................................................ 3

8 Procedure..................................................................................................................................................................................................................... 4

9 Expression of results ........................................................................................................................................................................................ 4

10 Precision ....................................................................................................................................................................................................................... 4

11 Test report ................................................................................................................................................................................................................... 5

Bibliography ................................................................................................................................................................................................................................ 6

© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 13517:2020
ISO 13517:2020(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to

the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see

www .iso .org/ iso/ for
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.