Forestry machinery - Wood chippers - Safety

Wood chippers with integrated chain conveyors in the infeed chute. 2nd Paragraph - Add after the 1st sentence the following:
"It also applies to chippers fitted with an integrated feed belt or chain conveyor."
Modifications to Clauses 1, 3, 4, 5.4, 6.1, 6.3, B.4.2 and Annex C.

Land- und Forstmaschinen - Buschholzhacker - Sicherheit

Machines forestieres - Déchiqueteuses - Sécurité

Gozdarski stroji - Sekalniki - Varnost

General Information

Status
Not Published
Current Stage
98 - Abandoned project (Adopted Project)
Start Date
29-Oct-2013
Due Date
03-Nov-2013
Completion Date
29-Oct-2013

Relations

Buy Standard

Draft
EN 13525:2005/oprA1:2005
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI SIST EN
13525:2005/oprA1:2005

PREDSTANDARD
maj 2005
Gozdarski stroji - Sekalniki - Varnost
Forestry machinery - Wood chippers - Safety
ICS 65.060.80 Referenčna številka
SIST EN 13525:2005/oprA1:2005(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
DRAFT
EN 13525:2005
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
March 2005
ICS
English version
Forestry machinery - Wood chippers - Safety
Machines forestières - Déchiqueteuses - Sécurité Forstmaschinen - Buschholtzhacker - Sicherheit
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 144.
This draft amendment A1, if approved, will modify the European Standard EN 13525:2005. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status
as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13525:2005/prA1:2005: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 13525:2004/prA1:2005 (E)
Foreword
This document (EN 13525:2004/prA1:2005) has been prepared by Technical Committee CEN/TC 144
“Tractors and machinery for agriculture and forestry”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
2

---------------------- Page: 3 ----------------------

EN 13525:2004/prA1:2005 (E)

Scope
nd st
2 Paragraph - Add after the 1 sentence the following:
“It also applies to chippers fitted with an integrated feed belt or chain conveyor.”
2 Normative references
Add the following reference:
“EN 620:2002, Continuous handling equipment and systems - Safety and EMC requirements for fixed belt
conveyors for bulk materials”
3 Definitions
Amend definition 3.6 to read:
“belt chain or similar conveyor, either in front …”
4.3.3 Hazards related to infeed components and chipping components
Replace clause 4.3.3.2 by th
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.