Terrestrial Trunked Radio (TETRA); Emergency access

This TBR specifies the technical characteristics to be provided by TETRA terminal equipment which is capable of connection to a Public Telecommunications Network (PTN) and which uses the TETRA technology. The objective of this TBR is to ensure that no disturbance occurs to the PTN, and to ensure interworking btw. PTN and TETRA terminals and btw. TETRA terminal to TETRA terminal so that the communication can be routed successfully through the applicable network(s). The requirements in this TBR apply together with the attachment requirements for the appropriate PTN and the requirement of any other applicable TBR. It does not add or reduce the attachment requirements unless there is a particular effect on the network which is unique to TETRA. Note: appropriate PTN refers to TBR for basic rate ISDN, TBR for primary rate ISDN or national regulations (implemeting ETS 300 001) for PSTN.  TETRA terminal equipment consists of several elements. This TBR is structured to allow testing and approval of the individual elements as separate items. Because of the need for effective use of the radio frequency spectrum, the essential air interface characteristics shall be tested. For each essential requirement, a test is given including measurement methods. Requirements apply to the public network interface and the RF Air Interface of the equipment, which may be stimulated to perform the tests by additional equipment, if necessary. Terminal equipment may be subject to additional requirements in other applicable CTRs or Directives depending on the functionality (primary functions). This TBR is based on the radio and protocol provisions of ETS 300 394. This document is a general TBR for TETRA terminal equipment, however, only certain applications are subject to Directive 91/263/EEC and hence covered by a CTR. It is therefore necessary to check with the relevant CTR as to the applicability to specific applications.

Prizemni snopovni radio (TETRA) - Dostop v sili

General Information

Status
Published
Publication Date
31-Aug-2002
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Sep-2002
Due Date
01-Sep-2002
Completion Date
01-Sep-2002
Mandate

Buy Standard

Standardization document
P TBR 035:1999
English language
76 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standardization document
TBR 035:2002
English language
76 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
3SIST TBR 035:
01-RNWREHU
Prizemni snopovni radio (TETRA) - Dostop v sili
Terrestrial Trunked Radio (TETRA); Emergency access
Ta slovenski standard je istoveten z: TBR 035 E1
ICS:
33.070.10 Prizemni snopovni radio Terrestrial Trunked Radio
(TETRA) (TETRA)
3SIST TBR 035: en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST TBR 035:2002

---------------------- Page: 2 ----------------------

SIST TBR 035:2002
TECHNICAL TBR 35
BASIS for September 1998
REGULATION
Source: TETRA Reference: DTBR/TETRA-02016
ICS: 33.020
Key words: TETRA, radio, type approval
Terrestrial Trunked Radio (TETRA);
Emergency access
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Internet: secretariat@etsi.fr - http://www.etsi.fr - http://www.etsi.org
Tel.: +33 4 92 94 42 00 - Fax: +33 4 93 65 47 16
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1998. All rights reserved.

---------------------- Page: 3 ----------------------

SIST TBR 035:2002
Page 2
TBR 35: September 1998
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Standards Making Support Dept." at the address shown on the title page.

---------------------- Page: 4 ----------------------

SIST TBR 035:2002
Page 3
TBR 35: September 1998
Contents
Foreword . 5
1 Scope. 7
2 Normative references . 7
3 Definitions, symbols and abbreviations. 8
3.1 Definitions. 8
3.2 Symbols. 8
3.3 Abbreviations. 9
4 Requirements. 10
4.1 Introduction. 10
4.2 Requirements at the Um air interface. 11
4.2.1 Physical layer requirements. 11
4.2.2 Codec requirements. 15
4.2.3 Layer 2 requirements . 16
4.2.4 Layer 3 requirements . 22
4.2.5 Security requirements . 28
4.2.6 Other entities at the Um air interface . 28
4.3 Requirements at the Ud air interface. 28
4.4 Other interfaces. 28
5 TBR test specification . 29
5.1 Introduction. 29
5.2 Environmental conditions . 29
5.3 Test configuration. 30
5.4 Um air interface test specification . 30
5.4.1 Physical layer test specification . 30
5.4.1.1 Test case index for physical layer . 30
5.4.1.2 Test case selection expression definitions for physical
layer. 34
5.4.2 Codec test specification. 35
5.4.2.1 Test case index for codec . 35
5.4.2.2 Test case selection expression definitions for codec. 36
5.4.3 Layer 2 test specification . 37
5.4.3.1 Test suite structure for MAC layer. 37
5.4.3.2 Test case index for MAC layer . 38
5.4.3.3 Test case selection expression definitions for MAC layer. 38
5.4.3.4 Test suite parameter definitions for MAC layer. 39
5.4.3.5 Test suite structure for LLC layer . 40
5.4.3.6 Test case index for LLC layer . 41
5.4.3.7 Test case selection expression definitions for LLC layer . 42
5.4.3.8 Test suite parameter definitions for LLC layer . 42
5.4.4 Layer 3 test specification . 43
5.4.4.1 Test suite structure for layer 3. 43
5.4.4.2 Test case index for layer 3 . 45
5.4.4.3 Test case selection expression definitions for layer 3. 50
5.4.4.4 Test suite parameter definitions for layer 3. 51
Annex A (normative): TBR Requirements Tables (TBR-RT). 53
A.1 Introduction . 53
A.2 Requirements tables for Um air interface . 54
A.2.1 General. 54

---------------------- Page: 5 ----------------------

SIST TBR 035:2002
Page 4
TBR 35: September 1998
A.2.2 Physical layer.55
A.2.3 Codec.58
A.2.4 Layer 2 .59
A.2.4.1 Lower MAC layer.59
A.2.4.2 Upper MAC layer.59
A.2.4.3 LLC layer .63
A.2.5 Layer 3 .65
A.2.5.1 CMCE requirements.65
A.2.5.2 MM requirements .69
A.2.5.3 MLE requirements.71
Annex B (normative): Declarations on parameters supported .73
B.1 Introduction.73
B.2 Declarations for Um air interface.73
B.2.1 Layer 2 .73
B.2.1.1 MAC layer.73
B.2.2 Layer 3 .74
B.2.2.1 CMCE.74
B.2.2.2 MM .74
B.2.2.3 MLE .74
Annex C (informative): Bibliography.75
History.76

---------------------- Page: 6 ----------------------

SIST TBR 035:2002
Page 5
TBR 35: September 1998
Foreword
This Technical Basis for Regulation (TBR) has been produced by the ETSI Project Terrestrial Trunked
Radio (TETRA) of the European Telecommunications Standards Institute (ETSI).

---------------------- Page: 7 ----------------------

SIST TBR 035:2002
Page 6
TBR 35: September 1998
Blank Page

---------------------- Page: 8 ----------------------

SIST TBR 035:2002
Page 7
TBR 35: September 1998
1 Scope
This TBR specifies the technical characteristics to be provided by Terrestorial Trunked Radio (TETRA)
terminal equipment which is capable of connecting and inter-working with a public telecommunications
network and which uses the TETRA technology. It applies only to terminal equipment intended for police
and emergency services operating within European harmonised frequency bands in the range 380 MHz to
383 MHz and 390 MHz to 393 MHz.
NOTE 1: These frequency bands may be extended by an additional 2 MHz at a later time.
The objective of this TBR is to ensure that no disturbance occurs to the public telecommunications
network, to ensure inter-working between public telecommunications networks and TETRA terminals and
TETRA terminal to TETRA terminal so that communication can be routed successfully through the
applicable network(s).
The requirements in this TBR apply together with the attachment requirements for the appropriate public
telecommunications network and the requirements of any other applicable TBR. It does not add to, or
reduce, the attachment requirements unless there is a particular effect on the network which is unique to
TETRA.
NOTE 2: Appropriate public telecommunications network refers to the TBR for basic rate
Integrated Services Digital Network (ISDN), the TBR for primary rate ISDN or the
national regulations (implementing ETS 300 001) for Public Switched
Telecommunications Network.
TETRA terminal equipment consists of several elements. This TBR is structured to allow testing and
approval of the individual elements as separate items. Due to the need for effective use of the radio
spectrum, the essential air interface characteristics have to be tested. For each essential requirement a
test is given including measurement methods.
Requirements apply to the public network interface and the Radio Frequency (RF) interface of the
equipment, which may be stimulated to perform the tests by additional equipment.
In this TBR there are no additional Electromagnetic Compatibility (EMC) requirements in terms of the
Terminal Directive 91/263/EEC [13], article 4c.
NOTE 3: Technical requirements for EMC performance and testing of the equipment are
covered by the relevant standards applicable to the EMC Directive 89/336/EEC.
Terminal equipment may be subject to additional requirements in other applicable Common Technical
Requirements (CTRs), or European Directives depending on the functionality (i.e. primary functions).
2 Normative references
This TBR incorporates, by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to this TBR only when incorporated in it by amendment or revision. For undated references the
latest edition of the publication referred to applies.
[1] ETS 300 392-2 (March 1996): "Radio Equipment and Systems (RES);
Trans-European Trunked Radio (TETRA); Voice plus Data (V+D); Part 2: Air
interface".
[2] ETS 300 392-10: "Trans-European Trunked Radio (TETRA); Voice plus Data
(V+D);Voice plus Data (V+D); Part 10: Supplementary services stage 1".
[3] ETS 300 392-11: "Radio Equipment and Systems (RES); Trans-European
Trunked Radio (TETRA); Voice plus Data (V+D); Part 11: Supplementary
Services (SS) stage 2".

---------------------- Page: 9 ----------------------

SIST TBR 035:2002
Page 8
TBR 35: September 1998
[4] ETS 300 392-12: "Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D);
Part 12: Supplementary Services (SS) stage 3".
[5] ETS 300 392-14: "Radio Equipment and Systems (RES); Trans-European
Trunked Radio (TETRA); Voice plus Data (V+D); Part 14: Protocol
Implementation Conformance Statement (PICS) proforma specification".
[6] ETS 300 394-1 (March 1996): "Radio Equipment and Systems (RES);
Trans-European Trunked Radio (TETRA); Conformance testing specification;
Part 1: Radio".
[7] ETS 300 394-2-1: "Terrestrial Trunked Radio (TETRA); Conformance testing
specification; Part 2: Protocol testing specification for Voice plus Data (V+D);
Sub-part 1: Test suite structure and test purposes".
[8] ETS 300 394-2-2: "Terrestrial Trunked Radio (TETRA); Conformance testing
specification; Part 2: Protocol testing specification for Voice plus Data (V+D);
Sub-part 2: Abstract Test Suite (ATS) for Network (NWK) layer".
[9] ETS 300 394-2-3: "Terrestrial Trunked Radio (TETRA); Conformance testing
specification; Part 2: Protocol testing specification for Voice plus Data (V+D);
Sub-part 3: Abstract Test Suite (ATS) for Logical Link Control (LLC)".
[10] ETS 300 394-2-4: "Terrestrial Trunked Radio (TETRA); Conformance testing
specification; Part 2: Protocol testing specification for Voice plus Data (V+D);
Sub-part 4: Abstract Test Suite (ATS) for Medium Access Control (MAC)".
[11] ETS 300 395-2 (December 1996): "Radio Equipment and Systems (RES);
Trans-European Trunked Radio (TETRA); Speech codec for full-rate traffic
channel; Part 2: TETRA codec".
[12] ETS 300 395-4 (February 1997): "Radio Equipment and Systems (RES);
Trans-European Trunked Radio (TETRA); Speech codec for full-rate traffic
channel; Part 4: Codec conformance testing".
[13] Council Directive 91/263/EEC of 29 April 1991 on the approximation of the laws
of the Member States concerning telecommunications terminal equipment,
including the mutual recognition of their conformity.
[14] Council Directive 89/336/EEC of 3 May 1989 on the approximation of the laws of
the Member States relating to electromagnetic compatibility.
[15] ISO/IEC 9646-3 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 3:
The tree and tabular combined notation". (See also CCITT Recommendation
X.292 (1992)).
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of this TBR, the definitions given in ETS 300 392-2 [1] apply.
3.2 Symbols
For the purposes of this TBR, the following symbols apply:
Um TETRA Voice plus Data (V+D) air interface
Ud TETRA Direct Mode (DM) air interface

---------------------- Page: 10 ----------------------

SIST TBR 035:2002
Page 9
TBR 35: September 1998
3.3 Abbreviations
For the purposes of this TBR, the following abbreviations apply:
AACH Access Assignment Channel
ATS Abstract Test Suite
BNCH Broadcast Network Channel
BS Base Station
BSCH Broadcast Synchronization Channel
Cat. Category
CC Call Control
CMCE Circuit Mode Control Entity
CONP Connection Oriented Network Protocol
CRC Cyclic Redundancy Check
CTR Common Technical Requirement
ETS European Telecommunication Standard
FCS Frame Check Sequence
ITSI Individual TETRA Subscriber Identity
IUT Implementation Under Test
LLC Logical Link Control
LS Line Station
MAC Medium Access Control
MCCH Main Control Channel
MCM Minimum Control Mode
MM Mobility Management
MS Mobile Station
NCM Normal Control Mode
PC Protocol Control
PDU Protocol Data Unit
PEI Peripheral Equipment Interface
PICS Protocol Implementation Conformance Statement
PIXIT Protocol Implementation eXtra Information for Testing
PUEM Probability of Undetected Erroneous Message
RCPC Rate-Compatible Punctured Convolutional
RT Requirements Table
SCCH Secondary Control Channel
SCH Signalling Channel
SCLNP Specific Connectionless Network Protocol
SDS Short Data Services
SDU Service Data Unit
SIM Subscriber Identity Module
SS Supplementary Service
STCH Stealing Channel
SwMI Switching and Management Infrastructure
TBR Technical Basis for Regulation
TSS Test Suite Structure
TP Test Purpose
TTCN Tree and Tabular Combined Notation
V+D Voice and Data

---------------------- Page: 11 ----------------------

SIST TBR 035:2002
Page 10
TBR 35: September 1998
4 Requirements
This clause references the requirements from the standards specifying TETRA. It also contains the
justifications for inclusion of the requirements, and a reference to the relevant test to verify compliance
with the requirement.
NOTE: This clause does not specify the exact status (e.g. mandatory or optional) of the listed
features, services and requirements. This is specified in the TBR Requirements Tables
(TBR-RT) in annex A.
4.1 Introduction
The following table headings are applicable to the tables in this clause:
Requirement reference: Reference to a (sub)clause(s) in the reference specification.
Description: A short description of the requirement.
Category (Cat.): The category in which the relative item falls under the article 4 in the Council
Directive 91/263/EEC [13].
The interpretation of category column in all tables is as follows:
d falls under item (d) from Article 4 of Council Directive 91/263/EEC [13],
"protection of the network from harm";
e falls under item (e) from Article 4 of Council Directive 91/263/EEC [13],
"effective use of radio frequency spectrum";
f falls under item (f) from Article 4 of Council Directive 91/263/EEC [13],
"interworking with the network";
g falls under item (g) from Article 4 of Council Directive 91/263/EEC [13],
"interworking via the network, in justified cases".
NOTE: There are no EMC technical requirements in this TBR, which are specific to the
equipment in terms of item (c) from Article 4 of Council Directive 91/263/EEC [23].
Other technical aspects of EMC performance and testing of the equipment are
covered by the relevant requirements of the EMC Directive, 89/336/EEC [14].
TBR justification: The justification for the requirement against the indicated category.
Test method reference: For physical layer and codec tables, a test method is referenced for each
requirement.
Test case limit value: For physical layer and codec tables, the limit values are indicated for a
requirement when applicable.
Test purpose reference: For protocol layer tables, at least one test purpose is referenced for each
requirement.
Test case reference: For protocol layer tables, at least one test case is referenced for each
requirement.

---------------------- Page: 12 ----------------------

SIST TBR 035:2002
4.2 Requirements at the Um air interface
4.2.1 Physical layer requirements
This subclause contains the radio layer requirements at the Um air interface.
Table 1: Radio layer requirements at the Um air interface
Requirement Description Cat. TBR justification Test case limit Test method
reference value reference reference
(note 1) (note 2) (note 3)
4.7 Modulation. d, e Incorrect modulation will lead to disturbance of other - Implicit by 10.1.3.
TETRA users.
6.4.1.1 BS transmitter output power. d, e Maladjustment of the RF output power may either cause 7.1.1.2 8.1.2
unnecessary interference in the radio spectrum or
decrease the probability of successful radio connections.
6.4.1.2 MS transmitter output power. d, e Maladjustment of the RF output power may either cause 7.1.1.2 8.1.1
unnecessary interference in the radio spectrum or
decrease the probability of successful radio connections.
6.4.1.2 MS transmitter output power control d, e Maladjustment of the RF output power may either cause 7.3.5.2 10.5
levels. unnecessary interference in the radio spectrum or
decrease the probability of successful radio connections.
6.4.2.2.1 Unwanted conducted emission over the d, e Unwanted emissions above an acceptable level may cause 7.1.3.2 8.3
useful part of the burst. unnecessary interference in the radio spectrum.
6.4.2.2.2 Unwanted conducted emission during d, e Unwanted emissions above an acceptable level may cause 7.1.4.2 8.4
the switching transients. unnecessary interference in the radio spectrum.
6.4.2.3 Unwanted conducted emission far from d, e Unwanted emissions above an acceptable level may cause 7.1.5.2 8.5
the carrier. unnecessary interference in the radio spectrum.
6.4.2.4 Unwanted conducted emission during d, e Unwanted emissions above an acceptable level may cause 7.1.7.2 8.7
CLCH and BLCH. unnecessary interference in the radio spectrum.
6.4.2.5 Unwanted conducted emission in the d, e Unwanted emissions above an acceptable level may cause 7.2.8.2 9.8
non-transmit state. unnecessary interference in the radio spectrum.
6.4.3 Unwanted radiated emissions. d, e Unwanted emissions above an acceptable level may cause 7.1.6.2 8.6
unnecessary interference in the radio spectrum.
6.4.5 BS output power time mask. e A violation of the given RF power time mask may lead to 7.1.1.2 8.1.2
unnecessary interference in the radio spectrum.
(continued)
Page 11
TBR 35: September 1998

---------------------- Page: 13 ----------------------

SIST TBR 035:2002
Page 12
TBR 35: September 1998
Table 1 (continued): Radio layer requirements at the Um air interface
Requirement Description Cat. TBR justification Test case limit Test method
reference value reference reference
(note 1) (note 2) (note 3)
6.4.5 MS output power time mask. e A violation of the given RF power time mask may lead to 7.1.1.2 8.1.1 and 10.5
unnecessary interference in the radio spectrum.
6.4.5.1 BS output power in non-active transmit e A violation of the given RF power time mask may lead to 7.1.2.2 8.2
state. unnecessary interference in the radio spectrum.
6.4.5.2 MS output power in non-active transmit e A violation of the given RF power time mask may lead to 7.1.2.2 8.2
state. unnecessary interference in the radio spectrum.
6.4.6.2 BS intermodulation attenuation. d, e An intermodulation attenuation below an acceptable level 7.1.8.2.2 8.8 and 8.8.2
may cause unnecessary interference in the radio spectrum.
6.4.6.3 MS intermodulation attenuation. d, e An intermodulation attenuation below an acceptable level 7.1.8.2.1 8.8 and 8.8.1
may cause unnecessary interference in the radio spectrum.
6.4.7 Intra-BS intermodulation attenuation. d, e An Intra-BS intermodulation attenuation below an 7.1.8.2.3 8.8 and 8.8.3
acceptable level may cause unnecessary interference in
the radio spectrum.
6.5.1.2 Blocking characteristics. e Insufficient blocking characteristics of the receiver may 7.2.5.2 9.5.1 and 9.5.2
lead to an unnecessarily high number of radio transmission
attempts
6.5.2.2 Spurious response rejection. d, e Insufficient spurious response rejection may lead to an 7.2.6.2 9.6
unnecessarily high number of radio transmission attempts.
6.5.3.2 Intermodulation response rejection. d, e Insufficient intermodulation response rejection may lead to 7.2.7.2 9.7.1 and 9.7.2
an unnecessarily high number of radio transmission
attempts
6.5.4.2 Unwanted conducted emission in d, e Unwanted emissions above an acceptable level may cause 7.2.8.2 9.8
reception. unnecessary interference in the radio spectrum.
6.5.5 Unwanted radiated emission. d, e Unwanted emissions above an acceptable level may cause 7.2.9.2 9.8
unnecessary interference in the radio spectrum.
6.6.1.2 Modulation accuracy. e, f Insufficient modulation accuracy may lead to the 7.3.1.2 10.1.1, 10.1.2 and
transmission of incorrect data. 10.1.3
6.6.2.1 Nominal error rate. e, f An unacceptable nominal error rate may lead to the 7.2.2.2 9.2.1 and 9.2.2
reception of incorrect data.
6.6.2.2 Dynamic reference sensitivity e, f An unacceptable dynamic reference sensitivity 7.2.3.2 9.3.1, 9.3.2 and
performance. performance may lead to the reception of incorrect data. 9.3.3
(continued)

---------------------- Page: 14 ----------------------

SIST TBR 035:2002
Table 1 (continued): Radio layer requirements at the Um air interface
Requirement Description Cat. TBR justification Test case limit Test method
reference value reference reference
(note 1) (note 2) (note 3)
6.6.2.2.1 BS dynamic reference sensitivity e, f An unacceptable dynamic reference sensitivity 7.2.3.2 9.3.2
performance. performance may lead to the reception of incorrect data.
6.6.2.2.2 MS dynamic reference sensitivity e, f An unacceptable dynamic reference sensitivity 7.2.3.2 9.3.1
performance. performance may lead to the reception of incorrect data.
6.6.2.3 Reference interference performance. e, f An unacceptable reference interference performance may 7.2.4.2 9.4.1 and 9.4.2
lead to the reception of incorrect data.
6.6.2.3.1 BS reference interference performance. e, f An unacceptable reference interference performance may 7.2.4.2 9.4.2
lead to the reception of incorrect data.
6.6.2.3.2 MS reference interference performance. e, f An unacceptable reference interference performance may 7.2.4.2 9.4.1
lead to the reception of incorrect data.
6.6.2.4 Static reference sensitivity performance. e, f An unacceptable static reference sensitivity performance Implicit by 7.2.5.2, Implicit by 9.5.1,
may lead to the reception of incorrect data. 7.2.6.2 and 7.2.7.2 9.5.2, 9.6, 9.7.1
and 9.7.2.
6.6.2.4.1 BS static reference sensitivity e, f An unacceptable static reference sensitivity performance Implicit by 7.2.5.2, Implicit by 9.5.2,
performance. may lead to the reception of incorrect data. 7.2.6.2 and 7.2.7.2 9.6, and 9.7.2.
6.6.2.4.2 MS static reference sensitivity e, f An unacceptable static reference sensitivity performance Implicit by 7.2.5.2, Implicit by 9.5.1,
performance. may lead to the reception of incorrect data. 7.2.6.2 and 7.2.7.2 9.6 and 9.7.1.
6.6.2.5 MS receiver performance for d, e An insufficient synchronisation burst acquisition may cause - Implicit by MAC
synchronisation burst acquisition. unnecessary interference in the radio spectrum. layer testing.
7.4 Timing of transmitted signal. d, e An insufficient synchronisation may cause unnecessary - Implicit by MAC
interference in the radio spectrum. layer testing.
7.5 BS requirement for synchronisation. d, e An insufficient synchronisation may cause unnecessary 7.3.2.2 10.2.2
interference in the radio spectrum.
7.6 MS requirement for synchronisation. d, e An insufficient synchronisation may cause unnecessary 7.3.2.2 and 7.3.4.2 10.2.1 and 10.4
interference in the radio spectrum.
9.5.2 Mapping of BCCH and CLCH. d, e Incorrect mapping of BCCH and CLCH may cause - Implicit by MAC
interference with other users. layer testing.
9.5.3 Mapping of SCH. d, e Incorrect mapping of SCH may cause interference with - Implicit by MAC
other users. layer testing.
9.5.4 Mapping of TCH and STCH. d, e Incorrect mapping of TCH and STCH may cause - Implicit by CMCE
interference with other users. layer testing.
(continued)
Page 13
TBR 35: September 1998

---------------------- Page: 15 ----------------------

SIST TBR 035:2002
Page 14
TBR 35: September 1998
Table 1 (concluded): Radio layer requirements at the Um air interface
Requirement Description Cat. TBR justification Test case limit Test method
reference value reference reference
(note 1) (note 2) (note 3)
9.5.5 Mapping of AACH. d, e Incorrect mapping of AACH may cause interference with - Implicit by MAC
other users. layer testing.
10.2 RF power control. d, e, f An insufficient RF power control may either cause 7.3.5.2 10.5
unnecessary interference in the radio spectrum or
decrease the probability of successful radio connections.
10.3.1 Received signal strength. d, e, f If the received signal strength is not measured sufficiently 7.3.5.2 10.5
accurate this may lead to a maladjustment of the RF output
power and thus either cause unnecessary interference in
the radio spectrum or decrease the probability of
successful radio connections.
23.4.4.2 MS open loop power control. d, e, f An insufficient RF
...

SLOVENSKI STANDARD
SIST TBR 035:2002
01-september-2002
Prizemni snopovni radio (TETRA) - Dostop v sili
Terrestrial Trunked Radio (TETRA); Emergency access
Ta slovenski standard je istoveten z: TBR 035 Edition 1
ICS:
33.070.10 Prizemni snopovni radio Terrestrial Trunked Radio
(TETRA) (TETRA)
SIST TBR 035:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST TBR 035:2002

---------------------- Page: 2 ----------------------

SIST TBR 035:2002
TECHNICAL TBR 35
BASIS for September 1998
REGULATION
Source: TETRA Reference: DTBR/TETRA-02016
ICS: 33.020
Key words: TETRA, radio, type approval
Terrestrial Trunked Radio (TETRA);
Emergency access
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Internet: secretariat@etsi.fr - http://www.etsi.fr - http://www.etsi.org
Tel.: +33 4 92 94 42 00 - Fax: +33 4 93 65 47 16
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1998. All rights reserved.

---------------------- Page: 3 ----------------------

SIST TBR 035:2002
Page 2
TBR 35: September 1998
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Standards Making Support Dept." at the address shown on the title page.

---------------------- Page: 4 ----------------------

SIST TBR 035:2002
Page 3
TBR 35: September 1998
Contents
Foreword . 5
1 Scope. 7
2 Normative references . 7
3 Definitions, symbols and abbreviations. 8
3.1 Definitions. 8
3.2 Symbols. 8
3.3 Abbreviations. 9
4 Requirements. 10
4.1 Introduction. 10
4.2 Requirements at the Um air interface. 11
4.2.1 Physical layer requirements. 11
4.2.2 Codec requirements. 15
4.2.3 Layer 2 requirements . 16
4.2.4 Layer 3 requirements . 22
4.2.5 Security requirements . 28
4.2.6 Other entities at the Um air interface . 28
4.3 Requirements at the Ud air interface. 28
4.4 Other interfaces. 28
5 TBR test specification . 29
5.1 Introduction. 29
5.2 Environmental conditions . 29
5.3 Test configuration. 30
5.4 Um air interface test specification . 30
5.4.1 Physical layer test specification . 30
5.4.1.1 Test case index for physical layer . 30
5.4.1.2 Test case selection expression definitions for physical
layer. 34
5.4.2 Codec test specification. 35
5.4.2.1 Test case index for codec . 35
5.4.2.2 Test case selection expression definitions for codec. 36
5.4.3 Layer 2 test specification . 37
5.4.3.1 Test suite structure for MAC layer. 37
5.4.3.2 Test case index for MAC layer . 38
5.4.3.3 Test case selection expression definitions for MAC layer. 38
5.4.3.4 Test suite parameter definitions for MAC layer. 39
5.4.3.5 Test suite structure for LLC layer . 40
5.4.3.6 Test case index for LLC layer . 41
5.4.3.7 Test case selection expression definitions for LLC layer . 42
5.4.3.8 Test suite parameter definitions for LLC layer . 42
5.4.4 Layer 3 test specification . 43
5.4.4.1 Test suite structure for layer 3. 43
5.4.4.2 Test case index for layer 3 . 45
5.4.4.3 Test case selection expression definitions for layer 3. 50
5.4.4.4 Test suite parameter definitions for layer 3. 51
Annex A (normative): TBR Requirements Tables (TBR-RT). 53
A.1 Introduction . 53
A.2 Requirements tables for Um air interface . 54
A.2.1 General. 54

---------------------- Page: 5 ----------------------

SIST TBR 035:2002
Page 4
TBR 35: September 1998
A.2.2 Physical layer.55
A.2.3 Codec.58
A.2.4 Layer 2 .59
A.2.4.1 Lower MAC layer.59
A.2.4.2 Upper MAC layer.59
A.2.4.3 LLC layer .63
A.2.5 Layer 3 .65
A.2.5.1 CMCE requirements.65
A.2.5.2 MM requirements .69
A.2.5.3 MLE requirements.71
Annex B (normative): Declarations on parameters supported .73
B.1 Introduction.73
B.2 Declarations for Um air interface.73
B.2.1 Layer 2 .73
B.2.1.1 MAC layer.73
B.2.2 Layer 3 .74
B.2.2.1 CMCE.74
B.2.2.2 MM .74
B.2.2.3 MLE .74
Annex C (informative): Bibliography.75
History.76

---------------------- Page: 6 ----------------------

SIST TBR 035:2002
Page 5
TBR 35: September 1998
Foreword
This Technical Basis for Regulation (TBR) has been produced by the ETSI Project Terrestrial Trunked
Radio (TETRA) of the European Telecommunications Standards Institute (ETSI).

---------------------- Page: 7 ----------------------

SIST TBR 035:2002
Page 6
TBR 35: September 1998
Blank Page

---------------------- Page: 8 ----------------------

SIST TBR 035:2002
Page 7
TBR 35: September 1998
1 Scope
This TBR specifies the technical characteristics to be provided by Terrestorial Trunked Radio (TETRA)
terminal equipment which is capable of connecting and inter-working with a public telecommunications
network and which uses the TETRA technology. It applies only to terminal equipment intended for police
and emergency services operating within European harmonised frequency bands in the range 380 MHz to
383 MHz and 390 MHz to 393 MHz.
NOTE 1: These frequency bands may be extended by an additional 2 MHz at a later time.
The objective of this TBR is to ensure that no disturbance occurs to the public telecommunications
network, to ensure inter-working between public telecommunications networks and TETRA terminals and
TETRA terminal to TETRA terminal so that communication can be routed successfully through the
applicable network(s).
The requirements in this TBR apply together with the attachment requirements for the appropriate public
telecommunications network and the requirements of any other applicable TBR. It does not add to, or
reduce, the attachment requirements unless there is a particular effect on the network which is unique to
TETRA.
NOTE 2: Appropriate public telecommunications network refers to the TBR for basic rate
Integrated Services Digital Network (ISDN), the TBR for primary rate ISDN or the
national regulations (implementing ETS 300 001) for Public Switched
Telecommunications Network.
TETRA terminal equipment consists of several elements. This TBR is structured to allow testing and
approval of the individual elements as separate items. Due to the need for effective use of the radio
spectrum, the essential air interface characteristics have to be tested. For each essential requirement a
test is given including measurement methods.
Requirements apply to the public network interface and the Radio Frequency (RF) interface of the
equipment, which may be stimulated to perform the tests by additional equipment.
In this TBR there are no additional Electromagnetic Compatibility (EMC) requirements in terms of the
Terminal Directive 91/263/EEC [13], article 4c.
NOTE 3: Technical requirements for EMC performance and testing of the equipment are
covered by the relevant standards applicable to the EMC Directive 89/336/EEC.
Terminal equipment may be subject to additional requirements in other applicable Common Technical
Requirements (CTRs), or European Directives depending on the functionality (i.e. primary functions).
2 Normative references
This TBR incorporates, by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to this TBR only when incorporated in it by amendment or revision. For undated references the
latest edition of the publication referred to applies.
[1] ETS 300 392-2 (March 1996): "Radio Equipment and Systems (RES);
Trans-European Trunked Radio (TETRA); Voice plus Data (V+D); Part 2: Air
interface".
[2] ETS 300 392-10: "Trans-European Trunked Radio (TETRA); Voice plus Data
(V+D);Voice plus Data (V+D); Part 10: Supplementary services stage 1".
[3] ETS 300 392-11: "Radio Equipment and Systems (RES); Trans-European
Trunked Radio (TETRA); Voice plus Data (V+D); Part 11: Supplementary
Services (SS) stage 2".

---------------------- Page: 9 ----------------------

SIST TBR 035:2002
Page 8
TBR 35: September 1998
[4] ETS 300 392-12: "Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D);
Part 12: Supplementary Services (SS) stage 3".
[5] ETS 300 392-14: "Radio Equipment and Systems (RES); Trans-European
Trunked Radio (TETRA); Voice plus Data (V+D); Part 14: Protocol
Implementation Conformance Statement (PICS) proforma specification".
[6] ETS 300 394-1 (March 1996): "Radio Equipment and Systems (RES);
Trans-European Trunked Radio (TETRA); Conformance testing specification;
Part 1: Radio".
[7] ETS 300 394-2-1: "Terrestrial Trunked Radio (TETRA); Conformance testing
specification; Part 2: Protocol testing specification for Voice plus Data (V+D);
Sub-part 1: Test suite structure and test purposes".
[8] ETS 300 394-2-2: "Terrestrial Trunked Radio (TETRA); Conformance testing
specification; Part 2: Protocol testing specification for Voice plus Data (V+D);
Sub-part 2: Abstract Test Suite (ATS) for Network (NWK) layer".
[9] ETS 300 394-2-3: "Terrestrial Trunked Radio (TETRA); Conformance testing
specification; Part 2: Protocol testing specification for Voice plus Data (V+D);
Sub-part 3: Abstract Test Suite (ATS) for Logical Link Control (LLC)".
[10] ETS 300 394-2-4: "Terrestrial Trunked Radio (TETRA); Conformance testing
specification; Part 2: Protocol testing specification for Voice plus Data (V+D);
Sub-part 4: Abstract Test Suite (ATS) for Medium Access Control (MAC)".
[11] ETS 300 395-2 (December 1996): "Radio Equipment and Systems (RES);
Trans-European Trunked Radio (TETRA); Speech codec for full-rate traffic
channel; Part 2: TETRA codec".
[12] ETS 300 395-4 (February 1997): "Radio Equipment and Systems (RES);
Trans-European Trunked Radio (TETRA); Speech codec for full-rate traffic
channel; Part 4: Codec conformance testing".
[13] Council Directive 91/263/EEC of 29 April 1991 on the approximation of the laws
of the Member States concerning telecommunications terminal equipment,
including the mutual recognition of their conformity.
[14] Council Directive 89/336/EEC of 3 May 1989 on the approximation of the laws of
the Member States relating to electromagnetic compatibility.
[15] ISO/IEC 9646-3 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 3:
The tree and tabular combined notation". (See also CCITT Recommendation
X.292 (1992)).
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of this TBR, the definitions given in ETS 300 392-2 [1] apply.
3.2 Symbols
For the purposes of this TBR, the following symbols apply:
Um TETRA Voice plus Data (V+D) air interface
Ud TETRA Direct Mode (DM) air interface

---------------------- Page: 10 ----------------------

SIST TBR 035:2002
Page 9
TBR 35: September 1998
3.3 Abbreviations
For the purposes of this TBR, the following abbreviations apply:
AACH Access Assignment Channel
ATS Abstract Test Suite
BNCH Broadcast Network Channel
BS Base Station
BSCH Broadcast Synchronization Channel
Cat. Category
CC Call Control
CMCE Circuit Mode Control Entity
CONP Connection Oriented Network Protocol
CRC Cyclic Redundancy Check
CTR Common Technical Requirement
ETS European Telecommunication Standard
FCS Frame Check Sequence
ITSI Individual TETRA Subscriber Identity
IUT Implementation Under Test
LLC Logical Link Control
LS Line Station
MAC Medium Access Control
MCCH Main Control Channel
MCM Minimum Control Mode
MM Mobility Management
MS Mobile Station
NCM Normal Control Mode
PC Protocol Control
PDU Protocol Data Unit
PEI Peripheral Equipment Interface
PICS Protocol Implementation Conformance Statement
PIXIT Protocol Implementation eXtra Information for Testing
PUEM Probability of Undetected Erroneous Message
RCPC Rate-Compatible Punctured Convolutional
RT Requirements Table
SCCH Secondary Control Channel
SCH Signalling Channel
SCLNP Specific Connectionless Network Protocol
SDS Short Data Services
SDU Service Data Unit
SIM Subscriber Identity Module
SS Supplementary Service
STCH Stealing Channel
SwMI Switching and Management Infrastructure
TBR Technical Basis for Regulation
TSS Test Suite Structure
TP Test Purpose
TTCN Tree and Tabular Combined Notation
V+D Voice and Data

---------------------- Page: 11 ----------------------

SIST TBR 035:2002
Page 10
TBR 35: September 1998
4 Requirements
This clause references the requirements from the standards specifying TETRA. It also contains the
justifications for inclusion of the requirements, and a reference to the relevant test to verify compliance
with the requirement.
NOTE: This clause does not specify the exact status (e.g. mandatory or optional) of the listed
features, services and requirements. This is specified in the TBR Requirements Tables
(TBR-RT) in annex A.
4.1 Introduction
The following table headings are applicable to the tables in this clause:
Requirement reference: Reference to a (sub)clause(s) in the reference specification.
Description: A short description of the requirement.
Category (Cat.): The category in which the relative item falls under the article 4 in the Council
Directive 91/263/EEC [13].
The interpretation of category column in all tables is as follows:
d falls under item (d) from Article 4 of Council Directive 91/263/EEC [13],
"protection of the network from harm";
e falls under item (e) from Article 4 of Council Directive 91/263/EEC [13],
"effective use of radio frequency spectrum";
f falls under item (f) from Article 4 of Council Directive 91/263/EEC [13],
"interworking with the network";
g falls under item (g) from Article 4 of Council Directive 91/263/EEC [13],
"interworking via the network, in justified cases".
NOTE: There are no EMC technical requirements in this TBR, which are specific to the
equipment in terms of item (c) from Article 4 of Council Directive 91/263/EEC [23].
Other technical aspects of EMC performance and testing of the equipment are
covered by the relevant requirements of the EMC Directive, 89/336/EEC [14].
TBR justification: The justification for the requirement against the indicated category.
Test method reference: For physical layer and codec tables, a test method is referenced for each
requirement.
Test case limit value: For physical layer and codec tables, the limit values are indicated for a
requirement when applicable.
Test purpose reference: For protocol layer tables, at least one test purpose is referenced for each
requirement.
Test case reference: For protocol layer tables, at least one test case is referenced for each
requirement.

---------------------- Page: 12 ----------------------

SIST TBR 035:2002
4.2 Requirements at the Um air interface
4.2.1 Physical layer requirements
This subclause contains the radio layer requirements at the Um air interface.
Table 1: Radio layer requirements at the Um air interface
Requirement Description Cat. TBR justification Test case limit Test method
reference value reference reference
(note 1) (note 2) (note 3)
4.7 Modulation. d, e Incorrect modulation will lead to disturbance of other - Implicit by 10.1.3.
TETRA users.
6.4.1.1 BS transmitter output power. d, e Maladjustment of the RF output power may either cause 7.1.1.2 8.1.2
unnecessary interference in the radio spectrum or
decrease the probability of successful radio connections.
6.4.1.2 MS transmitter output power. d, e Maladjustment of the RF output power may either cause 7.1.1.2 8.1.1
unnecessary interference in the radio spectrum or
decrease the probability of successful radio connections.
6.4.1.2 MS transmitter output power control d, e Maladjustment of the RF output power may either cause 7.3.5.2 10.5
levels. unnecessary interference in the radio spectrum or
decrease the probability of successful radio connections.
6.4.2.2.1 Unwanted conducted emission over the d, e Unwanted emissions above an acceptable level may cause 7.1.3.2 8.3
useful part of the burst. unnecessary interference in the radio spectrum.
6.4.2.2.2 Unwanted conducted emission during d, e Unwanted emissions above an acceptable level may cause 7.1.4.2 8.4
the switching transients. unnecessary interference in the radio spectrum.
6.4.2.3 Unwanted conducted emission far from d, e Unwanted emissions above an acceptable level may cause 7.1.5.2 8.5
the carrier. unnecessary interference in the radio spectrum.
6.4.2.4 Unwanted conducted emission during d, e Unwanted emissions above an acceptable level may cause 7.1.7.2 8.7
CLCH and BLCH. unnecessary interference in the radio spectrum.
6.4.2.5 Unwanted conducted emission in the d, e Unwanted emissions above an acceptable level may cause 7.2.8.2 9.8
non-transmit state. unnecessary interference in the radio spectrum.
6.4.3 Unwanted radiated emissions. d, e Unwanted emissions above an acceptable level may cause 7.1.6.2 8.6
unnecessary interference in the radio spectrum.
6.4.5 BS output power time mask. e A violation of the given RF power time mask may lead to 7.1.1.2 8.1.2
unnecessary interference in the radio spectrum.
(continued)
Page 11
TBR 35: September 1998

---------------------- Page: 13 ----------------------

SIST TBR 035:2002
Page 12
TBR 35: September 1998
Table 1 (continued): Radio layer requirements at the Um air interface
Requirement Description Cat. TBR justification Test case limit Test method
reference value reference reference
(note 1) (note 2) (note 3)
6.4.5 MS output power time mask. e A violation of the given RF power time mask may lead to 7.1.1.2 8.1.1 and 10.5
unnecessary interference in the radio spectrum.
6.4.5.1 BS output power in non-active transmit e A violation of the given RF power time mask may lead to 7.1.2.2 8.2
state. unnecessary interference in the radio spectrum.
6.4.5.2 MS output power in non-active transmit e A violation of the given RF power time mask may lead to 7.1.2.2 8.2
state. unnecessary interference in the radio spectrum.
6.4.6.2 BS intermodulation attenuation. d, e An intermodulation attenuation below an acceptable level 7.1.8.2.2 8.8 and 8.8.2
may cause unnecessary interference in the radio spectrum.
6.4.6.3 MS intermodulation attenuation. d, e An intermodulation attenuation below an acceptable level 7.1.8.2.1 8.8 and 8.8.1
may cause unnecessary interference in the radio spectrum.
6.4.7 Intra-BS intermodulation attenuation. d, e An Intra-BS intermodulation attenuation below an 7.1.8.2.3 8.8 and 8.8.3
acceptable level may cause unnecessary interference in
the radio spectrum.
6.5.1.2 Blocking characteristics. e Insufficient blocking characteristics of the receiver may 7.2.5.2 9.5.1 and 9.5.2
lead to an unnecessarily high number of radio transmission
attempts
6.5.2.2 Spurious response rejection. d, e Insufficient spurious response rejection may lead to an 7.2.6.2 9.6
unnecessarily high number of radio transmission attempts.
6.5.3.2 Intermodulation response rejection. d, e Insufficient intermodulation response rejection may lead to 7.2.7.2 9.7.1 and 9.7.2
an unnecessarily high number of radio transmission
attempts
6.5.4.2 Unwanted conducted emission in d, e Unwanted emissions above an acceptable level may cause 7.2.8.2 9.8
reception. unnecessary interference in the radio spectrum.
6.5.5 Unwanted radiated emission. d, e Unwanted emissions above an acceptable level may cause 7.2.9.2 9.8
unnecessary interference in the radio spectrum.
6.6.1.2 Modulation accuracy. e, f Insufficient modulation accuracy may lead to the 7.3.1.2 10.1.1, 10.1.2 and
transmission of incorrect data. 10.1.3
6.6.2.1 Nominal error rate. e, f An unacceptable nominal error rate may lead to the 7.2.2.2 9.2.1 and 9.2.2
reception of incorrect data.
6.6.2.2 Dynamic reference sensitivity e, f An unacceptable dynamic reference sensitivity 7.2.3.2 9.3.1, 9.3.2 and
performance. performance may lead to the reception of incorrect data. 9.3.3
(continued)

---------------------- Page: 14 ----------------------

SIST TBR 035:2002
Table 1 (continued): Radio layer requirements at the Um air interface
Requirement Description Cat. TBR justification Test case limit Test method
reference value reference reference
(note 1) (note 2) (note 3)
6.6.2.2.1 BS dynamic reference sensitivity e, f An unacceptable dynamic reference sensitivity 7.2.3.2 9.3.2
performance. performance may lead to the reception of incorrect data.
6.6.2.2.2 MS dynamic reference sensitivity e, f An unacceptable dynamic reference sensitivity 7.2.3.2 9.3.1
performance. performance may lead to the reception of incorrect data.
6.6.2.3 Reference interference performance. e, f An unacceptable reference interference performance may 7.2.4.2 9.4.1 and 9.4.2
lead to the reception of incorrect data.
6.6.2.3.1 BS reference interference performance. e, f An unacceptable reference interference performance may 7.2.4.2 9.4.2
lead to the reception of incorrect data.
6.6.2.3.2 MS reference interference performance. e, f An unacceptable reference interference performance may 7.2.4.2 9.4.1
lead to the reception of incorrect data.
6.6.2.4 Static reference sensitivity performance. e, f An unacceptable static reference sensitivity performance Implicit by 7.2.5.2, Implicit by 9.5.1,
may lead to the reception of incorrect data. 7.2.6.2 and 7.2.7.2 9.5.2, 9.6, 9.7.1
and 9.7.2.
6.6.2.4.1 BS static reference sensitivity e, f An unacceptable static reference sensitivity performance Implicit by 7.2.5.2, Implicit by 9.5.2,
performance. may lead to the reception of incorrect data. 7.2.6.2 and 7.2.7.2 9.6, and 9.7.2.
6.6.2.4.2 MS static reference sensitivity e, f An unacceptable static reference sensitivity performance Implicit by 7.2.5.2, Implicit by 9.5.1,
performance. may lead to the reception of incorrect data. 7.2.6.2 and 7.2.7.2 9.6 and 9.7.1.
6.6.2.5 MS receiver performance for d, e An insufficient synchronisation burst acquisition may cause - Implicit by MAC
synchronisation burst acquisition. unnecessary interference in the radio spectrum. layer testing.
7.4 Timing of transmitted signal. d, e An insufficient synchronisation may cause unnecessary - Implicit by MAC
interference in the radio spectrum. layer testing.
7.5 BS requirement for synchronisation. d, e An insufficient synchronisation may cause unnecessary 7.3.2.2 10.2.2
interference in the radio spectrum.
7.6 MS requirement for synchronisation. d, e An insufficient synchronisation may cause unnecessary 7.3.2.2 and 7.3.4.2 10.2.1 and 10.4
interference in the radio spectrum.
9.5.2 Mapping of BCCH and CLCH. d, e Incorrect mapping of BCCH and CLCH may cause - Implicit by MAC
interference with other users. layer testing.
9.5.3 Mapping of SCH. d, e Incorrect mapping of SCH may cause interference with - Implicit by MAC
other users. layer testing.
9.5.4 Mapping of TCH and STCH. d, e Incorrect mapping of TCH and STCH may cause - Implicit by CMCE
interference with other users. layer testing.
(continued)
Page 13
TBR 35: September 1998

---------------------- Page: 15 ----------------------

SIST TBR 035:2002
Page 14
TBR 35: September 1998
Table 1 (concluded): Radio layer requirements at the Um air interface
Requirement Description Cat. TBR justification Test case limit Test method
reference value reference reference
(note 1) (note 2) (note 3)
9.5.5 Mapping of AACH. d, e Incorrect mapping of AACH may cause interference with - Implicit by MAC
other users. layer testing.
10.2 RF power control. d, e, f An insufficient RF power control may either cause 7.3.5.2 10.5
unnecessary interference in the radio spectrum or
decrease the probability of successful radio connections.
10.3.1 Received signal strength. d, e, f If the received signal strength is not measured sufficiently 7.3.5.2 10.5
accurate this may lead to a maladjustment of the RF output
power and thus either cause unnecessary interference in
the radio spectrum or decrease the probability of
successful radio connections.
23.4.4.2 MS open loop power control. d, e, f An insufficient RF p
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.