SIST EN 60974-4:2007

Arc welding equipment -- Part 4: In-service inspection and testing

This part of IEC 60974 specifies test procedures for in-service inspection and, after repair, to ensure electrical safety. These test procedures are also applicable for maintenance. This standard is applicable to power sources together with ancillary equipment for arc welding, cutting and allied processes built in conformity with IEC 60974-1. This standard is not applicable to testing of new power sources or engine-driven power sources.

Lichtbogenschweißeinrichtungen - Teil 4: Besichtigung und Prüfung während des Betriebes

Matériel de soudage à l'arc -- Partie 4: Inspection et essai en service

Spécifie les procédures d'essai pour l'inspection en service et après réparation afin de garantir la sécurité électrique. Ces procédures d'essai s'appliquent également à la maintenance. S'applique aux sources de courant ainsi que leurs équipements auxiliaires pour le soudage à l'arc, le coupage et les techniques connexes construits conformément à la CEI 60974-1.

Oprema za obločno varjenje - 4. del: Pregledi in preskusi v delovanju (IEC 60974-4:2006)

General Information

• Status: Withdrawn
• Publication Date: 11-Sep-2007
• Withdrawal Date: 06-Jan-2014
• ICS: 25.160.30 - Welding equipment
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 06-Jan-2014
• Due Date: 29-Jan-2014
• Completion Date: 07-Jan-2014
• Directive: 2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
• Directive: 73/23/EEC - Electrical equipment designed for use within certain voltage limits
• Ref Project: EN 60974-4:2007 - Arc welding equipment - Part 4: In-service inspection and testing

Relations

• Revised: SIST EN 60974-4:2011 - Arc welding equipment - Part 4: Periodic inspection and testing (IEC 60974-4:2010)
• Effective Date: 07-Jan-2014
• Replaced By: SIST EN 60974-4:2011 - Arc welding equipment - Part 4: Periodic inspection and testing (IEC 60974-4:2010)
• Effective Date: 28-Jan-2023
• Replaced By: SIST EN 60974-4:2011 - Arc welding equipment - Part 4: Periodic inspection and testing (IEC 60974-4:2010)
• Effective Date: 02-Jan-2014

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60974-4:2007
01-oktober-2007
2SUHPD]DREORþQRYDUMHQMHGHO3UHJOHGLLQSUHVNXVLYGHORYDQMX,(&

Arc welding equipment -- Part 4: In-service inspection and testing
Lichtbogenschweißeinrichtungen - Teil 4: Besichtigung und Prüfung während des
Betriebes
Matériel de soudage a l'arc -- Partie 4: Inspection et essai en service
Ta slovenski standard je istoveten z: EN 60974-4:2007
ICS:
25.160.30 Varilna oprema Welding equipment
SIST EN 60974-4:2007 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 60974-4

NORME EUROPÉENNE
February 2007
EUROPÄISCHE NORM

ICS 25.160


English version


Arc welding equipment -
Part 4: In-service inspection and testing
(IEC 60974-4:2006)


Matériel de soudage à l'arc -  Lichtbogenschweißeinrichtungen -
Partie 4: Inspection et essai en service Teil 4: Instandhaltung und Prüfung
(CEI 60974-4:2006) (IEC 60974-4:2006)




This European Standard was approved by CENELEC on 2006-12-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60974-4:2007 E

---------------------- Page: 2 ----------------------

EN 60974-4:2007 - 2 -
Foreword
The text of document 26/340/FDIS, future edition 1 of IEC 60974-4, prepared by IEC TC 26, Electric
welding, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60974-4 on 2006-12-01.
This standard is to be used in conjunction with EN 60974-1.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2007-09-01
– latest date by which the national standards conflicting
(dow) 2009-12-01
with the EN have to be withdrawn
This European Standard covers the essential requirements given in Article 4 of Council Directive
89/655/EEC concerning the minimum safety and health requirements for the use of work equipment by
workers at work, as amended by Directive 95/63/EC.
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60974-4:2006 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 60974-4:2007
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

1)
IEC 60050-151 - International Electrotechnical Vocabulary - -
(IEV) -
Part 151: Electrical and magnetic devices


1)
IEC 60050-195 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 195: Earthing and protection against
electric shock


1)
IEC 60050-851 - International electrotechnical vocabulary - -
(IEV) -
Chapter 851: Electric welding


1) 2)
IEC 60974-1 - Arc welding equipment - EN 60974-1 2005
Part 1: Welding power sources


1)
IEC 61557-4 - Electrical safety in low voltage distribution - -
systems up to 1 000 V a.c. and 1 500 V d.c. -
Equipment for testing, measuring or
monitoring of protective measures -
Part 4: Resistance of earth connection and
equipotential bonding




1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 4 ----------------------

NORME CEI
INTERNATIONALE
IEC



60974-4
INTERNATIONAL


Première édition
STANDARD

First edition

2006-10


Matériel de soudage à l’arc –
Partie 4:
Inspection et essai en service

Arc welding equipment –
Part 4:
In-service inspection and testing
© IEC 2006 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
CODE PRIX
N
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 5 ----------------------

60974-4 © IEC:2006 – 3 –
CONTENTS
FOREWORD.5

1 Scope.9
2 Normative references .9
3 Terms and definitions .9
4 General requirements .11
4.1 Qualification of test personnel .11
4.2 Test conditions.11
4.3 Measuring instruments .11
4.4 Periodic inspection and test.11
4.5 Maintenance.11
4.6 Repair .11
4.7 Test sequence.11
5 Protection against electrical shock.13
5.1 Visual inspection .13
5.2 Continuity of the protective circuit.13
5.3 Insulation resistance .15
5.4 Welding circuit leakage current.15
5.5 Primary leakage current .17
5.6 No-load voltage (U ).19
0
6 Functional test.21
6.1 Function .21
6.2 Supply-circuit on/off switching device .21
6.3 Voltage-reducing device .21
6.4 Magnetic gas valve.23
6.5 Signal and control lamps .23
7 Documentation .23
7.1 Test report .23
7.2 Labelling .23

Annex A (informative) Check-list for the visual inspection .25
Annex B (informative) Example of a test report after repair .27
Annex C (informative) Equipment not built in accordance with IEC 60974-1.29

Figure 1 – Measurement of leakage current of welding circuit .15
Figure 2 – Measuring network for primary leakage current .17
Figure 3 – Principles of primary leakage current measurement for single phase equipment .19
Figure 4 – Measurement of peak values.21

Table 1 – Test sequence on used arc welding equipment .13
Table 2 – Insulation resistance .15

---------------------- Page: 6 ----------------------

60974-4 © IEC:2006 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

ARC WELDING EQUIPMENT –

Part 4: In-service inspection and testing


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60974-4 has been prepared by IEC technical committee 26:
Electric welding.
The text of this standard is based on the following documents:
FDIS Report on voting
26/340/FDIS 26/343/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The list of all the parts of the IEC 60974 series, under the general title Arc welding equipment,
can be found on the IEC website.

---------------------- Page: 7 ----------------------

60974-4 © IEC:2006 – 7 –
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.

---------------------- Page: 8 ----------------------

60974-4 © IEC:2006 – 9 –
ARC WELDING EQUIPMENT –

Part 4: In-service inspection and testing



1 Scope
This part of IEC 60974 specifies test procedures for in-service inspection and, after repair, to
ensure electrical safety. These test procedures are also applicable for maintenance.
This standard is applicable to power sources together with ancillary equipment for arc
welding, cutting and allied processes built in conformity with IEC 60974-1.
This standard is not applicable to testing of new power sources or engine-driven power
sources.
NOTE For a power source not built in accordance with IEC 60974-1, see Annex C.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60050-151, International Electrotechnical Vocabulary (IEV) – Part 151: Electrical and
magnetic devices
IEC 60050-195, International Electrotechnical Vocabulary (IEV) – Part 195: Earthing and
protection against electric shock
IEC 60050-851, International Electrotechnical Vocabulary (IEV) – Chapter 851: Electric
welding
IEC 60974-1, Arc welding equipment – Part 1: Welding power sources
IEC 61557-4, Electrical safety in low voltage distribution systems up to 1000 V a.c. and
1500 V d.c. – Equipment for testing, measur
...