SIST EN 3710:2008

Aerospace series - Sockets, bi-hexagonal - Technical Specification

This standard specifies the properties of double-hex sockets for aerospace use.

Luft- und Raumfahrt - Steckschlüsseleinsätze, Doppelsechskant - Technische Lieferbedingungen

Diese Norm legt die Eigenschaften von Steckschlüsseleinsätzen mit Doppelsechskant für die Anwendung in der Luft- und Raumfahrt fest.

Série aérospatiale - Douille bihexagonale - Spécification technique

Aeronavtika - Obojke, biheksagonalne - Tehnična specifikacija

General Information

• Status: Published
• Publication Date: 20-May-2008
• ICS: 49.030.99 - Other fasteners
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 09-May-2008
• Due Date: 14-Jul-2008
• Completion Date: 21-May-2008
• Ref Project: EN 3710:2008 - Aerospace series - Sockets, bi-hexagonal - Technical Specification

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Steckschlüsseleinsätze, Doppelsechskant - Technische LieferbedingungenSérie aérospatiale - Douille bihexagonale - Spécification techniqueAerospace series - Sockets, bi-hexagonal - Technical Specification49.030.99Drugi vezni elementiOther fastenersICS:Ta slovenski standard je istoveten z:EN 3710:2008SIST EN 3710:2008en01-julij-2008SIST EN 3710:2008SLOVENSKI
STANDARD



SIST EN 3710:2008



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3710April 2008ICS 25.140.30 English VersionAerospace series - Sockets, bi-hexagonal - TechnicalSpecificationSérie aérospatiale - Douille bihexagonale - SpécificationtechniqueLuft- und Raumfahrt - Steckschlüsseleinsätze,Doppelsechskant - Technische LieferbedingungenThis European Standard was approved by CEN on 21 December 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3710:2008: ESIST EN 3710:2008



EN 3710:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Required characteristics.4 3.1 Configuration, dimensions, tolerances.4 3.2 Material.4 3.3 Hardness.4 3.4 Surface treatment.4 4 Designation.6 5 Marking.6 6 Technical specification.6
Figures Figure 1.5
Tables Table 1.5
SIST EN 3710:2008



EN 3710:2008 (E) 3 Foreword This document (EN 3710:2008) has been prepared by the Aerospace and Defence Industries A
...