EN 3710:2008
(Main)Aerospace series - Sockets, bi-hexagonal - Technical Specification
Aerospace series - Sockets, bi-hexagonal - Technical Specification
This standard specifies the properties of double-hex sockets for aerospace use.
Luft- und Raumfahrt - Steckschlüsseleinsätze, Doppelsechskant - Technische Lieferbedingungen
Diese Norm legt die Eigenschaften von Steckschlüsseleinsätzen mit Doppelsechskant für die Anwendung in der Luft- und Raumfahrt fest.
Série aérospatiale - Douille bihexagonale - Spécification technique
Aeronavtika - Obojke, biheksagonalne - Tehnična specifikacija
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Steckschlüsseleinsätze, Doppelsechskant - Technische LieferbedingungenSérie aérospatiale - Douille bihexagonale - Spécification techniqueAerospace series - Sockets, bi-hexagonal - Technical Specification49.030.99Drugi vezni elementiOther fastenersICS:Ta slovenski standard je istoveten z:EN 3710:2008SIST EN 3710:2008en01-julij-2008SIST EN 3710:2008SLOVENSKI
STANDARD
SIST EN 3710:2008
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3710April 2008ICS 25.140.30 English VersionAerospace series - Sockets, bi-hexagonal - TechnicalSpecificationSérie aérospatiale - Douille bihexagonale - SpécificationtechniqueLuft- und Raumfahrt - Steckschlüsseleinsätze,Doppelsechskant - Technische LieferbedingungenThis European Standard was approved by CEN on 21 December 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3710:2008: ESIST EN 3710:2008
EN 3710:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Required characteristics.4 3.1 Configuration, dimensions, tolerances.4 3.2 Material.4 3.3 Hardness.4 3.4 Surface treatment.4 4 Designation.6 5 Marking.6 6 Technical specification.6
Figures Figure 1.5
Tables Table 1.5
SIST EN 3710:2008
EN 3710:2008 (E) 3 Foreword This document (EN 3710:2008) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by October 2008. Attention is drawn to the possibility th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.