oSIST prEN 50483-1:2024
(Main)Test requirements for low voltage aerial bundled cable accessories - Part 1: Generalities
Test requirements for low voltage aerial bundled cable accessories - Part 1: Generalities
The EN 50483 series applies to overhead line fittings for tensioning, supporting and connecting aerial bundled cables (ABC) of rated voltage U0/U (Um): 0,6/1 (1,2) kV.
The purpose of this Part 1 is to define the common aspects of the products included in the above scope.
Prüfanforderungen für Bauteile für isolierte Niederspannungsfreileitungen - Teil 1: Allgemeines
Prescriptions relatives aux essais des accessoires pour réseaux aériens basse tension torsadés - Partie 1: Généralités
Zahteve za preskušanje pribora za nizkonapetostne izolirane nadzemne kable - 1. del: Glavne točke
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Zahteve za preskušanje pribora za nizkonapetostne izolirane nadzemne kable - 1.
del: Glavne točke
Test requirements for low voltage aerial bundled cable accessories - Part 1: Generalities
Prüfanforderungen für Bauteile für isolierte Niederspannungsfreileitungen - Teil 1:
Allgemeines
Prescriptions relatives aux essais des accessoires pour réseaux aériens basse tension
torsadés - Partie 1: Généralités
Ta slovenski standard je istoveten z: prEN 50483-1
ICS:
29.240.20 Daljnovodi Power transmission and
distribution lines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD DRAFT
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2024
ICS 29.240.20 Will supersede EN 50483-1:2009
English Version
Test requirements for low voltage aerial bundled cable
accessories - Part 1: Generalities
Prescriptions relatives aux essais des accessoires pour Prüfanforderungen für Bauteile für isolierte
réseaux aériens basse tension torsadés - Partie 1: Niederspannungsfreileitungen - Teil 1: Allgemeines
Généralités
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2025-01-03.
It has been drawn up by CLC/TC 20.
If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 79842 Ref. No. prEN 50483-1 E
Contents Page
1 European foreword . 3
2 Introduction . 4
3 1 Scope . 5
4 2 Normative references . 5
5 3 Terms and definitions . 5
6 4 Symbols . 9
7 5 Products concerned . 9
8 6 Marking . 9
9 7 Quality procedure . 10
10 8 Routine and sample tests . 10
11 8.1 General . 10
12 8.2 Checking compliance of the supplied products . 10
13 8.3 Final inspection and testing . 11
14 8.4 Inspection and test records . 11
15 9 Type tests . 11
16 9.1 Test conditions . 11
17 9.2 Test for permanent marking . 12
18 9.3 Tests and sample selection . 13
19 9.4 Test reports . 13
20 Annex A (normative) List of tests for compliance . 15
21 Annex B (normative) Test selection – Samples needed for type tests . 17
22 Annex C (informative) Highest rated temperatures of insulating compounds . 26
23 Bibliography . 28
Tables
No table of figures entries found.
24 European foreword
25 This document [prEN 50483-1:2024] has been prepared by WG 11 of CLC/TC 20 “Electric cables”.
26 This document is currently submitted to the Enquiry.
27 The following dates are proposed:
• latest date by which the existence of this (doa) dav + 6 months
document has to be announced at national
level
• latest date by which this document has to be (dop) dav + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dav + 36 months
conflicting with this document have to be (to be confirmed or
withdrawn modified when voting)
28 This document will supersede EN 50483-1:2009 and all of its amendments and corrigenda (if any).
29 prEN 50483-1:2024 includes the following significant technical changes with respect to EN 50483-1:2009:
30 This is Part 1 of CENELEC standard EN 50483 “Test requirements for low voltage aerial bundled cable
31 accessories”, which has six parts:
32 — Part 1: Generalities;
33 — Part 2: Tension and suspension clamps, fittings and brackets for self supporting system;
34 — Part 3: Tension and suspension clamps for neutral messenger system;
35 — Part 4: Connectors;
36 — Part 5: Electrical ageing test;
37 — Part 6: Environmental testing.
38 Introduction
39 The objective of the EN 50483 series is to provide a method of testing the suitability of accessories when used
40 under normal operating conditions with low voltage aerial bundled cables (ABC) complying with HD 626.
41 There is variation between the different ABC specifications provided by HD 626, and tests carried out on one
42 of the ABC types may not be completely applicable to ABC of a different specification. Therefore, the
43 purchasers of accessories tested to this European Standard, should ensure that all their requirements are
44 met.
45 Climate differs across Europe and in order to meet the differing geographic climatic conditions it is necessary
46 to provide a range of tests to meet these variations. A range of optional, additional tests is provided to meet
47 the varying climatic needs and these should be agreed between the customer and the manufacturer and/or
48 the supplier see Annex C in prEN 50483-6).
49 This European Standard does not invalidate existing approvals of products achieved on the basis of national
50 standards and specifications and/or the demonstration of satisfactory service performance. However, products
51 approved according to such national standards or specifications cannot directly claim approval to this
52 European Standard. It may be possible, subject to agreement between the customer and the manufacturer
53 and/or the supplier, and/or the relevant conformity assessment body, to demonstrate that conformity to the
54 earlier standard can be used to claim conformity to this standard, provided an assessment is made of any
55 additional type testing that may need to be carried out. Any such additional testing that is part of a sequence
56 of testing cannot be done separately.
57 1 Scope
58 The EN 50483 series applies to overhead line fittings for tensioning, supporting and connecting aerial bundled
59 cables (ABC) of rated voltage U0/U (Um): 0,6/1 (1,2) kV.
60 The purpose of this Part 1 is to define the common aspects of the products included in the above scope.
61 2 Normative references
62 The following documents are referred to in the text in such a way that some or all of their content constitutes
63 requirements of this document. For dated references, only the edition cited applies. For undated references,
64 the latest edition of the referenced document (including any amendments) applies.
65 EN 50483 (series), Test requirements for low voltage aerial bundled cable accessories
66 EN 60068-1:2014, Environmental testing - Part 1: General and guidance (IEC 60068-1:1988 + corrigendum
67 Oct. 1988 +A1:1992)
68 HD 626, Overhead distribution cables of rated voltage U /U(U ): 0,6/1 (1,2) kV
o m
69 IEC 60050-461, International Electrotechnical Vocabulary (IEV) – Part 461: Electric cables
70 3 Terms and definitions
71 For the purposes of this document, the terms and definitions given in IEC 60050-461 and the following apply.
72 ISO and IEC maintain terminology databases for use in standardization at the following addresses:
73 — ISO Online browsing platform: available at https://www.iso.org/obp/
74 — IEC Electropedia: available at https://www.electropedia.org/
75 3.1
76 adiabatic
77 occurring with no addition or loss of heat from the system under consideration
78 3.2
79 aerial bundled cable (ABC)
80 aerial cable consisting of a group of insulated conductors which are twisted together including, or not, a non
81 insulated conductor
82 Note 1 to entry: The terms bundled conductors, bundled cables, bundled cores, conductor bundles and bundle could be
83 used as equivalent to the term aerial bundled cable (ABC).
84 [SOURCE: IEV 461-08-02, modified]
85 3.3
86 aerial-insulated-cable
87 insulated cable designed to be suspended overhead and outdoors
88 [SOURCE: IEV 461-08-01]
89 3.4
90 angle of deviation
91 complementary angle to the angle defined by the two parts of the cable on both sides of the suspension clamp
92 3.5
93 branch connector
94 metallic device for connecting a branch conductor to a main conductor at an intermediate point on the latter
95 [SOURCE: IEV 461-17-05]
96 3.6
97 branch conductor
98 conductor connected to the main conductor by a connector
99 3.7
100 clamp bolt
101 bolt which tightens two parts of a clamp together
102 3.8
103 conductor insulation
104 insulation applied on a conductor
105 [SOURCE: IEV 461-02-02, modified]
106 3.9
107 conductor (of a cable)
108 part of a cable which has the specific function of carrying current
109 [SOURCE: IEV 461-01-01]
110 3.10
111 connector
112 metallic device to connect cable conductors together
113 [SOURCE: IEV 461-17-03]
114 3.11
115 core
116 assembly comprising conductor and its own insulation
117 [SOURCE: IEV 461-04-04, modified]
118 3.12
119 equalizer
120 arrangement used in the test loop to ensure a point of equipotential and uniform current distribution in a
121 stranded conductor
122 [SOURCE: EN IEC 61238-1-2:2019, 3.5]
123 3.13
124 fixture (or fitting)
125 device for attaching ABC tension or/and suspension clamps to a pole or to a wall
126 3.14
127 insulation (of a cable)
128 insulating materials incorporated in a cable with the specific function of withstanding voltage
129 [SOURCE: IEV 461-02-01]
130 3.15
131 insulation piercing connector (IPC)
132 connector in which electrical contact with the conductor is made by metallic protrusions which pierce the
133 insulation of the ABC core
134 [SOURCE: IEV 461-11-08, modified]
135 3.16
136 median connector
137 connector which during the first heat cycle records the third highest temperature of the six connectors in the
138 test loop
139 [SOURCE: EN IEC 61238-1-2:2019, 3.5]
140 3.17
141 messenger
142 wire or rope, the primary function of which is to support the cable in aerial installations, which may be separate
143 from or integral with the cable it supports
144 [SOURCE: IEV 461-08-03]
145 3.18
146 bracket (or fitting)
147 device for attaching ABC tension or/and suspension clamps to a pole or to a wall
148 3.19
149 minimum breaking load (MBL)
150 minimum breaking load of the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.