iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

kSIST-TS FprCEN/TS 18084:2024

(Main)

Road vehicles - Post Shredder Technology recycling - Design recommendations for plastic products

Road vehicles - Post Shredder Technology recycling - Design recommendations for plastic products

This document specifies recommendations for the design of polymeric products used in road vehicles to facilitate separation and recycling after shredding.
This document is not applicable to dismantling of road vehicles and removal of parts and components.
This document is not applicable to elastomers.

Straßenfahrzeuge - Nachgelagerte Shredder Recyclingtechnologie - Gestaltungsempfehlungen für Kunststoffprodukte

Dieses Dokument legt Empfehlungen für die Auslegung von polymerischen Produkten, die in Straßenfahrzeugen verwendet werden, fest, um die Trennung und Wiederverwertung nach der Zerkleinerung zu vereinfachen.
Dieses Dokument ist nicht anwendbar auf die Demontage von Straßenfahrzeugen und das Entfernen von Teilen und Bauteilen.
Dieses Dokument ist nicht anwendbar auf Elastomere.

Véhicules routiers - Recyclage par technologie post-broyage - Recommandations de conception pour les produits en plastiques

Cestna vozila - Recikliranje s tehnologijo naknadnega drobljenja - Priporočila za načrtovanje izdelkov iz polimernih materialov

General Information

Status
Not Published
Public Enquiry End Date
29-Jun-2024
ICS
13.030.50 - Recycling
83.140.01 - Rubber and plastics products in general
Technical Committee
I13 - Imaginarni 13
Current Stage
5520 - Unique Acceptance Procedure (UAP) (Adopted Project)
Start Date
08-May-2024
Due Date
25-Sep-2024
Mandate
M/584 - Plastics recycling and recycled plastics
M/XXX - Commission Implementing Decision on a standardisation request as regards ecodesign requirements for smartphones, mobile phones other than smartphones, cordless phones and slate tablets in support of Regulation (EU) 2023/1670 and Delegated Regulation (EU) 2023/1669
Ref Project
FprCEN/TS 18084 - Road vehicles - Post Shredder Technology recycling - Design recommendations for plastic products

Buy Standard

kTS FprCEN/TS 18084:2024 - BARVEkTS FprCEN/TS 18084:2024 - BARVE
PreviousNext
Draft
kTS FprCEN/TS 18084:2024 - BARVE
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 18084:2024
01-junij-2024
Cestna vozila - Recikliranje s tehnologijo naknadnega drobljenja - Priporočila za
načrtovanje izdelkov iz polimernih materialov
Road vehicles - Post Shredder Technology recycling - Design recommendations for
plastic products
Straßenfahrzeuge - Nachgelagerte Shredder Recyclingtechnologie -
Gestaltungsempfehlungen für Kunststoffprodukte
Véhicules routiers - Recyclage par technologie post-broyage - Recommandations de
conception pour les produits en plastiques
Ta slovenski standard je istoveten z: FprCEN/TS 18084
ICS:
13.030.50 Recikliranje Recycling
83.140.01 Izdelki iz gume in polimernih Rubber and plastics products
materialov na splošno in general
kSIST-TS FprCEN/TS 18084:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
kSIST-TS FprCEN/TS 18084:2024

---------------------- Page: 2 ----------------------
kSIST-TS FprCEN/TS 18084:2024


FINAL DRAFT
TECHNICAL SPECIFICATION
FprCEN/TS 18084
SPÉCIFICATION TECHNIQUE

TECHNISCHE SPEZIFIKATION

May 2024
ICS 13.030.50; 83.140.01
English Version

Road vehicles - Post Shredder Technology recycling -
Design recommendations for plastic products
Véhicules routiers - Recyclage par technologie post- Straßenfahrzeuge - Nachgelagerte Shredder
broyage - Recommandations de conception pour les Recyclingtechnologie - Gestaltungsempfehlungen für
produits en plastiques Kunststoffprodukte


This draft Technical Specification is submitted to CEN members for Vote. It has been drawn up by the Technical Committee
CEN/TC 301.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change
without notice and shall not be referred to as a Technical Specification.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 18084:2024 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
kSIST-TS FprCEN/TS 18084:2024
FprCEN/TS 18084:2024 (EN)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviations . 5
3.1 Terms and definitions . 5
3.2 Abbreviations . 8
4 Recommendations . 9
4.1 Single constituent polymers or polymer blends . 9
4.2 Bonded materials and materials compatibility . 11
4.2.1 General . 11
4.2.2 Bonding of compatible polymers .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 17410:2021(Main)
Plastics - Controlled loop recycling of PVC-U profiles from windows and doors
EN 17410:2021

This document defines quality and test methodologies for recycled PVC to be used in PVC window profile systems.
It contains a description of the controlled loop as such, the definition of those material transformation steps which are relevant for product quality, in particular recycling input and output and profile manufacturing input and output.
Traceability tools are specified to characterize this loop as a controlled loop.
With regard to PVC waste treatment, the present standard relates to existing standards such as EN 15343, EN 15346 and EN 15347
With regard to semifinished and/or finished products, it refers to the European Standard for un-plasticized PVC window profiles (see EN 12608-1) and to the European harmonized standard for windows and doors (see EN 14351-1).

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 18064-5:2024(Main)
Plastics - Quality recommendations and basis for specifications for application of plastic recyclates in products - Part 5 : Poly(vinyl chloride) (PVC)
prEN 18064-5

This document provides relevant characteristics and typical values for poly(vinyl chloride) (PVC) recyclates intended for groups of defined applications (the product families).
The relevant characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer’s defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in Annex A.
NOTE 2   The selection of relevant properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 18064-6:2024(Main)
Plastics - Quality recommendations and basis for specifications for application of plastic recyclates in products - Part 6 : Polystyrene (PS)
prEN 18064-6

This document provides relevant characteristics and typical values for polystyrene (PS) recyclates intended for groups of defined applications (the product families).
The relevant characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer’s defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in the Annex A.
NOTE 2   The selection of relevant properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 18064-4:2024(Main)
Plastics - Quality recommendations and basis for specifications for application of plastic recyclates in products - Part 4 : Poly(ethylene terephtalate) (PET)
prEN 18064-4

This document provides relevant characteristics and typical values for PET recyclates intended for groups of defined applications (the product families).
The relevant characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer's defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in the Annex A.
NOTE 2   The selection of relevant properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 18064-7:2024(Main)
Plastics - Quality recommendations and basis for specifications for application of plastic recyclates in products - Part 7 : Acrylonitrile- butadiene-styrene (ABS)
prEN 18064-7

This document provides relevant characteristics and typical values for Acrylonitrile-butadiene-styrene (ABS) recyclates intended for groups of defined applications (the product families).
The relevant characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer’s defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in Annex A.
NOTE 2   The selection of relevant properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 18064-2:2024(Main)
Plastics - Quality recommendations and basis for specifications for application of plastic recyclates in products - Part 2 : Polyethylene (PE)
prEN 18064-2

This document provides relevant characteristics and typical values for polyethylene (PE) recyclates intended for groups of defined applications (the product families).
The relevant characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer's defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in Annex A.
NOTE 2   The selection of relevant properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 18064-1:2024(Main)
Plastics - Quality recommendations and basis for specifications for application of plastic recyclates in products - Part 1: General aspects
prEN 18064-1

This document is the general part of the series that describes the designation system for plastic recyclates.
This document is dealing with recyclates after the recycling operation and prior to converting and compounding (when applicable). It is dealing with preparation of samples and determination of properties.
NOTE 1   This document supports the underlaying standards of this series that, per polymer type, provide an overview of the relevant characteristics and typical values for recyclates for use in certain application groups (product families) in combination with the relevant converting technologies.
NOTE 2   The overview of the relevant properties is based on and further extends the relevant properties given in EN ISO 10350 1.

  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 18064-3:2024(Main)
Plastics Quality recommendations and basis for specifications for application of plastic recyclates in products - Part 3 : Polypropylene (PP)
prEN 18064-3

This document provides relevant characteristics and typical values for polypropylene (PP) recyclates intended for groups of defined applications (the product families).
The relevant characteristics and typical values for the different product families are derived from the performance requirements of the products belonging to that family, including requirements for product manufacturing processes where applicable.
This document applies to plastic recyclates intended to be used for the manufacturing of (intermediate) products.
This document is intended to be used in conjunction with part 1 of this standard series, which describes the designation system for plastic recyclates. The designation system allows comparison between recycled and virgin material at the level of the polymer’s defined designatory properties.
NOTE 1   Examples of designations of plastic recyclates are given in Annex A.
NOTE 2   The selection of relevant properties for a product family is based on EN ISO 10350 1, extended with specific properties related to plastic recyclates.

  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 4641:2024(Main)
Rubber hoses and hose assemblies for water suction and discharge - Specification (ISO 4641:2024)
EN ISO 4641:2024

ISO 4641:2016 specifies the minimum requirements for textile-reinforced, smooth-bore rubber water-suction and discharge hoses and hose assemblies.
Three types of hoses and hose assemblies are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges:
- ambient temperatures: −25 °C to +70 °C;
- water temperatures during operation: 0 °C to +70 °C.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 8804-1:2024(Main)
Requirements for the training of scientific divers - Part 1: Scientific divers (ISO 8804-1:2024)
EN ISO 8804-1:2024

This 3 part standard specifies the requirements for the training of scientific divers at 3 levels. The standard shall be limited in its scope so as to be applicable to all disciplines of science.
Scientific Diver - Is capable of diving for scientific purposes under the supervision of an Advanced Scientific Diver and under the overall oversight of a Scientific Project Leader.
Advanced Scientific Diver - An individual with specific technical or academic skills capable of diving for scientific purposes.
Scientific Diving Project Leader - Is capable of overseeing the conduct of a scientific diving project.
Each standard will specify Competencies, Prerequisites for training, Introductory information, Required theoretical knowledge, Required practical skills, Practical training parameters and Evaluation criteria for training systems aimed at training Scientific Divers, Advanced Scientific Divers and Scientific Diving Project Leaders. It is envisaged that each part of this three part standard will be a stand-alone deliverable (similar to ISO 24801 parts one, two and three).

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day