SIST EN 303 340 V1.1.2:2016
(Main)Digital Terrestrial TV Broadcast Receivers - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
Digital Terrestrial TV Broadcast Receivers - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
The present document applies to digital terrestrial television broadcast receivers fitted with an external antenna input
(tuner port) capable of receiving DVB-T and/or DVB-T2 signals. Receivers without external antenna connectors,
receivers with diversity, and receivers intended for mobile or automotive reception are not covered by the present
document.
The present document contains the requirements for digital terrestrial television broadcast receivers to meet the essential
requirements of article 3.2 of Directive 2014/53/EU [i.3] that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
The present document includes considerations of interference from LTE transmissions in the 700 MHz and 800 MHz
bands and DTT transmissions in UHF band IV. The requirements of the installation system (antenna, feeder cable,
amplifiers, etc.) are not addressed.
There are country specific variations of frequency usage for digital terrestrial television reception and other users such
as mobile broadband.
The tests in the present document only apply if the DTT broadcast receiver supports the wanted signal configuration
used by the test in question. The applicable tests are summarized in annex E, table E.1.
Digitalni prizemni radiodifuzijski sprejemniki - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument se uporablja za digitalne prizemne radiodifuzijske sprejemnike z zunanjim antenskim vhodom (vrata uglaševalnika), ki lahko sprejemajo signale DVB-T in/ali DVB-T2. Sprejemniki brez zunanjega antenskega priključka, sprejemniki z diverziteto in sprejemniki, namenjeni za mobilno ali samodejno sprejemanje, niso zajeti v tem dokumentu.
Ta dokument vsebuje zahteve za digitalne prizemne radiodifuzijske sprejemnike za izpolnjevanje bistvenih zahtev člena 3.2 Direktive 2014/53/EU [i.3], kjer je navedeno, da radijska oprema optimalno uporablja in tudi podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivih motenj.
Ta dokument vključuje predvidene motnje iz prenosov LTE v pasovih 700 MHz in 800 MHz ter iz prenosov DTT v pasu UHF IV. Zahteve glede namestitvenega sistema (antena, napajalni kabel, ojačevalniki itd.) niso obravnavane.
V posameznih državah obstajajo razlike v uporabi frekvenc za digitalne prizemne radiodifuzijske sprejemnike in druge uporabnike, kot je širokopasovna mobilna tehnologija.
Preskusi v tem dokumentu veljajo le, če sprejemnik DTT podpira želeno konfiguracijo signalov, ki se uporablja pri zadevnem preskusu. Preskusi, ki se uporabljajo, so povzeti v dodatku E (preglednica E.1).
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Digital Terrestrial TV Broadcast Receivers - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU33.160.25Televizijski sprejemnikiTelevision receiversICS:Ta slovenski standard je istoveten z:ETSI EN 303 340 V1.1.2 (2016-09)SIST EN 303 340 V1.1.2:2016en01-december-2016SIST EN 303 340 V1.1.2:2016SLOVENSKI
STANDARD
SIST EN 303 340 V1.1.2:2016
ETSI EN 303 340 V1.1.2 (2016-09) Digital Terrestrial TV Broadcast Receivers; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 303 340 V1.1.2:2016
ETSI ETSI EN 303 340 V1.1.2 (2016-09) 2
Reference REN/ERM-TG17-14-CR Keywords digital, radio, receiver, TV ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 303 340 V1.1.2:2016
ETSI ETSI EN 303 340 V1.1.2 (2016-09) 3 Contents Intellectual Property Rights . 5 Foreword . 5 Modal verbs terminology . 5 1 Scope . 6 2 References . 6 2.1 Normative references . 6 2.2 Informative references . 6 3 Definitions, symbols, and abbreviations . 7 3.1 Definitions . 7 3.2 Symbols . 8 3.3 Abbreviations . 9 4 Technical requirements specifications . 9 4.1 Environmental profile . 9 4.2 Conformance requirements . 10 4.2.1 DVB-T and DVB-T2 configurations for testing . 10 4.2.2 Interference and wanted test signals . 11 4.2.3 Sensitivity . 11 4.2.3.1 Definition . 11 4.2.3.2 Method of Measurement . 11 4.2.3.2.1 Test arrangement description . 11 4.2.3.2.2 Test procedure . 11 4.2.3.3 Limits . 12 4.2.4 Adjacent channel selectivity . 12 4.2.4.1 Definition . 12 4.2.4.2 Method of Measurement . 13 4.2.4.2.1 Test arrangement description . 13 4.2.4.2.2 Requirements for the ACLR of the interfering signal . 13 4.2.4.2.3 Test procedure . 13 4.2.4.3 Limits . 15 4.2.5 Blocking . 16 4.2.5.1 Definition . 16 4.2.5.2 Method of Measurement . 16 4.2.5.2.1 Test arrangement description . 16 4.2.5.2.2 Requirements for the ACLR of the interfering signal . 16 4.2.5.2.3 Test procedure . 16 4.2.5.3 Limits . 16 4.2.6 Overloading . 17 4.2.6.1 Definition . 17 4.2.6.2 Method of Measurement . 17 4.2.6.2.1 Test arrangement description . 17 4.2.6.2.2 Requirements for the ACLR of the interfering signal . 17 4.2.6.2.3 Test procedure . 17 4.2.6.3 Limits . 18 4.2.7 Unwanted emissions in the spurious domain . 18 4.2.7.1 Definition . 18 4.2.7.2 Method of Measurement . 19 4.2.7.3 Limits . 19 5 Testing for compliance with technical requirements . 19 5.1 Environmental conditions for testing . 19 5.2 Interpretation of the measurement results . 19 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 20 SIST EN 303 340 V1.1.2:2016
ETSI ETSI EN 303 340 V1.1.2 (2016-09) 4 Annex B (informative): Summary of study work . 21 B.1 Overview . 21 B.2 Selection of interferer waveforms . 21 B.2.1 UE waveform . 21 B.2.2 BS waveforms . 22 B.3 Reception conditions for LTE UE 700 MHz interference . 24 B.3.1 Calculation of maximum coupling gain . 24 B.3.2 Calculation of maximum received UE interference power . 25 B.4 Choice of BS interference power in receiver tests . 25 Annex C (informative): Measurement records . 26 Annex D (informative): Additional information to assist measurements . 28 D.1 Optional elements of the test arrangement . 28 D.2 Instrument settings for measuring the power of bursty interference signals . 28 D.3 Improving ACLR . 28 D.4 Measuring ACLR . 29 Annex E (normative): Applicable tests . 30 E.1 Applicable tests for different receiver variants . 30 Annex F (normative): Requirements for the interfering signal minimum ACLR . 31 Annex G (informative): Change History . 32 History . 33
SIST EN 303 340 V1.1.2:2016
ETSI ETSI EN 303 340 V1.1.2 (2016-09) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.11] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.3]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document has a number of interference test data files that are contained in archive en_303340v010102p0.zip which accompanies the present document.
National transposition dates Date of latest announcement of this EN (doa): 30 December 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 June 2017 Date of withdrawal of any conflicting National Standard (dow): 30 June 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
SIST EN 303 340 V1.1.2:2016
ETSI ETSI EN 303 340 V1.1.2 (2016-09) 6 1 Scope The present document applies to digital terrestrial television broadcast receivers fitted with an external antenna input (tuner port) capable of receiving DVB-T and/or DVB-T2 signals. Receivers without external antenna connectors, receivers with diversity, and receivers intended for mobile or automotive reception are not covered by the present document. The present document contains the requirements for digital terrestrial television broadcast receivers to meet the essential requirements of article 3.2 of Directive 2014/53/EU [i.3] that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. The present document includes considerations of interference from LTE transmissions in the 700 MHz and 800 MHz bands and DTT transmissions in UHF band IV. The requirements of the installation system (antenna, feeder cable, amplifiers, etc.) are not addressed. Table 1: Broadcast frequency bands Broadcast frequency bands VHF III UHF IV and V
There are country specific variations of frequency usage for digital terrestrial television reception and other users such as mobile broadband. The tests in the present document only apply if the DTT broadcast receiver supports the wanted signal configuration used by the test in question. The applicable tests are summarized in annex E, table E.1.
2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] CENELEC EN 55032:2015: "Electromagnetic compatibility of multimedia equipment. Emission requirements". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. SIST EN 303 340 V1.1.2:2016
ETSI ETSI EN 303 340 V1.1.2 (2016-09) 7 [i.1] Nordig: "NorDig Unified Test Plan for Integrated Receiver Decoders v2.4". [i.2] British Broadcasting Corporation and Arqiva, WHP288: "WSD Coexistence Testing at the Building Research Establishment: An Experimental Validation of Ofcom Regulatory Proposals". [i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. [i.4] ETSI EN 300 744 (V1.6.1): "Digital Video Broadcasting (DVB); Framing structure, channel coding and modulation for digital terrestrial television". [i.5] ETSI EN 302 755 (V1.3.1): "Digital Video Broadcasting (DVB); Frame structure channel coding and modulation for a second generation digital terrestrial television broadcasting system (DVB-T2)". [i.6] ETSI TR 100 028-1 (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 1". [i.7] ETSI TR 100 028-2 (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 2". [i.8] CEPT/ERC/Recommendation 74-01E (2011): "Unwanted emissions in the spurious domain". [i.9] ECC Report 186 (2013): "Technical and operational requirements for the operation of white space devices under geo-location approach". [i.10] Recommendation ITU-R BT.1729 (2005): "Common 16:9 or 4:3 aspect ratio digital television reference test pattern". [i.11] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. [i.12] Recommendation ITU-R BT.419-3 (1990): "Directivity and polarization discrimination of antennas in the reception of television broadcasting". 3 Definitions, symbols, and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: Adjacent Channel Leakage power Ratio (ACLR): ratio of the on-channel transmit power to the power measured in one of the adjacent channels with no active channel in the adjacent channel NOTE: In the present document this definition also applies to an unwanted signal at a specified frequency offset in a non-adjacent channel. adjacent channel selectivity: measure of the capability of the receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of an unwanted signal which differs in frequency from the wanted signal by an amount equal to the adjacent channel separation for which the equipment is intended NOTE 1: In the present document adjacent channel selectivity is determined by the onset of picture degradation. NOTE 2: The interference power I is equal to the licensed power of the interferer. This definition does not have the same meaning as the term "Adjacent Channel Selectivity" (ACS) used in other organizations such as ITU, CEPT, and in co-existence studies. The adjacent channel selectivity in the present document is equivalent to the measured I/C ratio. SIST EN 303 340 V1.1.2:2016
ETSI ETSI EN 303 340 V1.1.2 (2016-09) 8 NOTE 3: In the present document this definition also applies to an unwanted signal at a specified frequency offset in a non-adjacent channel. blocking or desensitization: measure of the capability of the receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of an unwanted signal at any frequency other than those of the spurious responses or of the adjacent channels NOTE 1: In the present document receiver blocking is determined by the onset of picture degradation. NOTE 2: The wanted signal level in the blocking tests of the present document is set at the specified receiver sensitivity level plus 6 dB. broadcast receiver: digital terrestrial television broadcast receiver comprising of at least a tuner and demodulator broadcast receiver tuner port: DTT receiver tuner RF input connector licensed power: highest rms power of the active portions of the signal measured over a specific time period NOTE: In the case of interference power measurements, this is the reference power used for I/C calculations in the present document. Typically for cases of LTE interference, this power is measured with a spectrum analyser in zero span with a gated power measurement function and rms detector over a period equal to an LTE symbol time. Alternatively it can be calculated by measuring the long term rms power and adding the appropriate LAPR from table 5. long term rms power: rms power of the signal measured over a period long enough to smooth out any fluctuations in the signal power over time such as those due to transmission bursts NOTE: This can be measured on an average power meter with an input filter time constant set high enough to average out fluctuations in the measured signal power or alternatively using a spectrum analyser with settings shown in table D.1. onset of picture degradation: minimum time between successive errors in the displayed video is 15 seconds radio equipment: product or relevant component thereof capable of communication by means of the emission and/or reception of radio waves utilizing the spectrum allocated to terrestrial/space radio communication NOTE: For the purposes of the present document the radio equipment is a digital terrestrial television broadcast receiver comprising of at least a tuner and demodulator. receiver overloading: interfering signal level expressed in dBm, above which the receiver begins to lose its ability to discriminate against interfering signals at frequencies differing from that of the wanted signal due to the onset of strong non-linear behaviour NOTE 1: In the present document the overload level is determined by the onset of picture degradation. NOTE 2: Above the overloading level the receiver will behave in a non-linear way, but does not necessarily fail immediately depending on the receiver and interference characteristics. sensitivity: maximum usable sensitivity is defined as the minimum receiver Radio Frequency (RF) input signal level or field strength able to produce a specified analogue SINAD ratio or Bit Error Ratio (BER), or other specified output performance which depends on this input signal level NOTE: In the present document receiver sensitivity is determined by the onset of picture degradation. 3.2 Symbols For the purposes of the present document, the following symbols apply: C Wanted signal GC Coupling Gain
I Interferer signal Ilic Licensed power Irms Long term rms power PRX_UE Received UE interference power PUE UE transmitted power SIST EN 303 340 V1.1.2:2016
ETSI ETSI EN 303 340 V1.1.2 (2016-09) 9 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: ACE Active Constellation Extension ACLR Adjacent Channel Leakage power Ratio ACS Adjacent Channel Selectivity AGC Automatic Gain Control BER Bit Error Ratio BS Base Station for mobile communications CEPT European Conference of Postal and Telecommunications Administrations DTG UK Digital TV Group DTT Digital Terrestrial Television DVB-T Digital Video Broadcast Terrestrial - first generation [i.4] DVB-T2 Digital Video Broadcast Terrestrial - second generation [i.5] FEC Forward Error Correction FEF Future Extension Frame FFT Fast Fourier Transform HEM High Efficiency Mode ISSY Input Stream SYnchronizer QAM Quadrature Amplitude Modulation LAPR Licensed to Average Power Ratio NOTE: This is the ratio of the licensed power (described above) to the long term rms power (described above) of the signal. LDPC Low Density Parity Check (codes) LTE Long Term Evolution PAPR Peak to Average Power Ratio PLP Physical Layer Pipe 64-QAM 64-ary Quadrature Amplitude Modulation 256-QAM 256-ary Quadrature Amplitude Modulation RF Radio Frequency SINAD (Signal + Noise + Distortion)/(Noise + Distortion) ratio SISO Single Input Single Output (meaning one transmitting and one receiving antenna) TFS Time-Frequency Slicing UE User Equipment for mobile communications NOTE: Example handsets, dongles, etc. UHF Ultra High Frequency VHF Very High Frequency 4 Technical requirements specifications 4.1 Environmental profile The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the manufacturer. The equipment shall comply with all the technical requirements of the present document at all times when operating within the boundary limits of the declared operational environmental profile. NOTE: The applicability of the different tests as defined in annex E may vary depending upon the selected country profile.
SIST EN 303 340 V1.1.2:2016
ETSI ETSI EN 303 340 V1.1.2 (2016-09) 10 4.2 Conformance requirements 4.2.1 DVB-T and DVB-T2 configurations for testing Representative DVB-T and DVB-T2 configurations used for conformance specification and testing are shown in tables 2 and 3. These are used in the Nordig specification test plan [i.1]. Table 2: DVB-T configuration Parameter Value for "7 MHz" VHF tests Value for "8 MHz" UHF tests Bandwidth 6,66 MHz 7,61 MHz FFT size 8K 8K Modulation 64-QAM 64-QAM Hierarchy Non-Hierarchical Non-Hierarchical Guard interval 1/4 1/4 Code rate 2/3 2/3 Channel Bandwidth 7 MHz 8 MHz
Table 3: DVB-T2 configuration Parameter Value for "7 MHz" VHF tests Value for "8 MHz" UHF tests Bandwidth 6,66 MHz 7,77 MHz FFT 32k 32k Carrier mode Normal Extended SISO/MISO SISO SISO Guard Interval 1/16 1/16 Version 1.2.1 1.2.1 Number of symbols/frame (Lf) 42 62 Pilot pattern PP4 PP4 TFS No No FEF Not used Not used Auxiliary streams Not used Not used Subslices / T2 frame 1 1 Frames / Superframe 2 2 L1 post FEC type 16k LDPC (see note 1) 16k LDPC (see note 1) L1 repetition 0 0 L1 post extension No No L1 post modulation 64 QAM 64-QAM L1 post scrambling None None L1_ACE_MAX 0 (see note 2) 0 (see note 2) L1 bias balancing cells No No PAPR L1-ACE & TR (see note 3) L1-ACE & TR (see note 3) PAPR: Vclip 3,1 V (see note 1) 3,1 V (see note 1) PAPR: Number of iterations 10 (see note 1) 10 (see note 1) TS bit rate (Mbit/s) 31,146 36,552 Input mode Mode A (single PLP mode) Mode A (single PLP mode) Number of PLPs 1 1 PLP type Data type 1 Data type 1 Constellation rotation Yes
...
ETSI EN 303 340 V1.1.2 (2016-09)
HARMONISED EUROPEAN STANDARD
Digital Terrestrial TV Broadcast Receivers;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
�
---------------------- Page: 1 ----------------------
2 ETSI EN 303 340 V1.1.2 (2016-09)
Reference
REN/ERM-TG17-14-CR
Keywords
digital, radio, receiver, TV
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 340 V1.1.2 (2016-09)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols, and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 8
3.3 Abbreviations . 9
4 Technical requirements specifications . 9
4.1 Environmental profile . 9
4.2 Conformance requirements . 10
4.2.1 DVB-T and DVB-T2 configurations for testing . 10
4.2.2 Interference and wanted test signals . 11
4.2.3 Sensitivity . 11
4.2.3.1 Definition . 11
4.2.3.2 Method of Measurement . 11
4.2.3.2.1 Test arrangement description . 11
4.2.3.2.2 Test procedure . 11
4.2.3.3 Limits . 12
4.2.4 Adjacent channel selectivity . 12
4.2.4.1 Definition . 12
4.2.4.2 Method of Measurement . 13
4.2.4.2.1 Test arrangement description . 13
4.2.4.2.2 Requirements for the ACLR of the interfering signal . 13
4.2.4.2.3 Test procedure . 13
4.2.4.3 Limits . 15
4.2.5 Blocking . 16
4.2.5.1 Definition . 16
4.2.5.2 Method of Measurement . 16
4.2.5.2.1 Test arrangement description . 16
4.2.5.2.2 Requirements for the ACLR of the interfering signal . 16
4.2.5.2.3 Test procedure . 16
4.2.5.3 Limits . 16
4.2.6 Overloading . 17
4.2.6.1 Definition . 17
4.2.6.2 Method of Measurement . 17
4.2.6.2.1 Test arrangement description . 17
4.2.6.2.2 Requirements for the ACLR of the interfering signal . 17
4.2.6.2.3 Test procedure . 17
4.2.6.3 Limits . 18
4.2.7 Unwanted emissions in the spurious domain . 18
4.2.7.1 Definition . 18
4.2.7.2 Method of Measurement . 19
4.2.7.3 Limits . 19
5 Testing for compliance with technical requirements . 19
5.1 Environmental conditions for testing . 19
5.2 Interpretation of the measurement results . 19
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 20
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 340 V1.1.2 (2016-09)
Annex B (informative): Summary of study work . 21
B.1 Overview . 21
B.2 Selection of interferer waveforms . 21
B.2.1 UE waveform . 21
B.2.2 BS waveforms . 22
B.3 Reception conditions for LTE UE 700 MHz interference . 24
B.3.1 Calculation of maximum coupling gain . 24
B.3.2 Calculation of maximum received UE interference power . 25
B.4 Choice of BS interference power in receiver tests . 25
Annex C (informative): Measurement records . 26
Annex D (informative): Additional information to assist measurements . 28
D.1 Optional elements of the test arrangement . 28
D.2 Instrument settings for measuring the power of bursty interference signals . 28
D.3 Improving ACLR . 28
D.4 Measuring ACLR . 29
Annex E (normative): Applicable tests . 30
E.1 Applicable tests for different receiver variants . 30
Annex F (normative): Requirements for the interfering signal minimum ACLR . 31
Annex G (informative): Change History . 32
History . 33
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 340 V1.1.2 (2016-09)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.11] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document has a number of interference test data files that are contained in archive
en_303340v010102p0.zip which accompanies the present document.
National transposition dates
Date of latest announcement of this EN (doa): 30 December 2016
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 June 2017
Date of withdrawal of any conflicting National Standard (dow): 30 June 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 303 340 V1.1.2 (2016-09)
1 Scope
The present document applies to digital terrestrial television broadcast receivers fitted with an external antenna input
(tuner port) capable of receiving DVB-T and/or DVB-T2 signals. Receivers without external antenna connectors,
receivers with diversity, and receivers intended for mobile or automotive reception are not covered by the present
document.
The present document contains the requirements for digital terrestrial television broadcast receivers to meet the essential
requirements of article 3.2 of Directive 2014/53/EU [i.3] that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
The present document includes considerations of interference from LTE transmissions in the 700 MHz and 800 MHz
bands and DTT transmissions in UHF band IV. The requirements of the installation system (antenna, feeder cable,
amplifiers, etc.) are not addressed.
Table 1: Broadcast frequency bands
Broadcast frequency bands
VHF III
UHF IV and V
There are country specific variations of frequency usage for digital terrestrial television reception and other users such
as mobile broadband.
The tests in the present document only apply if the DTT broadcast receiver supports the wanted signal configuration
used by the test in question. The applicable tests are summarized in annex E, table E.1.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CENELEC EN 55032:2015: "Electromagnetic compatibility of multimedia equipment. Emission
requirements".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 303 340 V1.1.2 (2016-09)
[i.1] Nordig: "NorDig Unified Test Plan for Integrated Receiver Decoders v2.4".
[i.2] British Broadcasting Corporation and Arqiva, WHP288: "WSD Coexistence Testing at the
Building Research Establishment: An Experimental Validation of Ofcom Regulatory Proposals".
[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.4] ETSI EN 300 744 (V1.6.1): "Digital Video Broadcasting (DVB); Framing structure, channel
coding and modulation for digital terrestrial television".
[i.5] ETSI EN 302 755 (V1.3.1): "Digital Video Broadcasting (DVB); Frame structure channel coding
and modulation for a second generation digital terrestrial television broadcasting system (DVB-
T2)".
[i.6] ETSI TR 100 028-1 (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 1".
[i.7] ETSI TR 100 028-2 (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 2".
[i.8] CEPT/ERC/Recommendation 74-01E (2011): "Unwanted emissions in the spurious domain".
[i.9] ECC Report 186 (2013): "Technical and operational requirements for the operation of white space
devices under geo-location approach".
[i.10] Recommendation ITU-R BT.1729 (2005): "Common 16:9 or 4:3 aspect ratio digital television
reference test pattern".
[i.11] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.12] Recommendation ITU-R BT.419-3 (1990): "Directivity and polarization discrimination of
antennas in the reception of television broadcasting".
3 Definitions, symbols, and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
Adjacent Channel Leakage power Ratio (ACLR): ratio of the on-channel transmit power to the power measured in
one of the adjacent channels with no active channel in the adjacent channel
NOTE: In the present document this definition also applies to an unwanted signal at a specified frequency offset
in a non-adjacent channel.
adjacent channel selectivity: measure of the capability of the receiver to receive a wanted modulated signal without
exceeding a given degradation due to the presence of an unwanted signal which differs in frequency from the wanted
signal by an amount equal to the adjacent channel separation for which the equipment is intended
NOTE 1: In the present document adjacent channel selectivity is determined by the onset of picture degradation.
NOTE 2: The interference power I is equal to the licensed power of the interferer. This definition does not have the
same meaning as the term "Adjacent Channel Selectivity" (ACS) used in other organizations such as ITU,
CEPT, and in co-existence studies. The adjacent channel selectivity in the present document is equivalent
to the measured I/C ratio.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 303 340 V1.1.2 (2016-09)
NOTE 3: In the present document this definition also applies to an unwanted signal at a specified frequency offset
in a non-adjacent channel.
blocking or desensitization: measure of the capability of the receiver to receive a wanted modulated signal without
exceeding a given degradation due to the presence of an unwanted signal at any frequency other than those of the
spurious responses or of the adjacent channels
NOTE 1: In the present document receiver blocking is determined by the onset of picture degradation.
NOTE 2: The wanted signal level in the blocking tests of the present document is set at the specified receiver
sensitivity level plus 6 dB.
broadcast receiver: digital terrestrial television broadcast receiver comprising of at least a tuner and demodulator
broadcast receiver tuner port: DTT receiver tuner RF input connector
licensed power: highest rms power of the active portions of the signal measured over a specific time period
NOTE: In the case of interference power measurements, this is the reference power used for I/C calculations in
the present document. Typically for cases of LTE interference, this power is measured with a spectrum
analyser in zero span with a gated power measurement function and rms detector over a period equal to
an LTE symbol time. Alternatively it can be calculated by measuring the long term rms power and adding
the appropriate LAPR from table 5.
long term rms power: rms power of the signal measured over a period long enough to smooth out any fluctuations in
the signal power over time such as those due to transmission bursts
NOTE: This can be measured on an average power meter with an input filter time constant set high enough to
average out fluctuations in the measured signal power or alternatively using a spectrum analyser with
settings shown in table D.1.
onset of picture degradation: minimum time between successive errors in the displayed video is 15 seconds
radio equipment: product or relevant component thereof capable of communication by means of the emission and/or
reception of radio waves utilizing the spectrum allocated to terrestrial/space radio communication
NOTE: For the purposes of the present document the radio equipment is a digital terrestrial television broadcast
receiver comprising of at least a tuner and demodulator.
receiver overloading: interfering signal level expressed in dBm, above which the receiver begins to lose its ability to
discriminate against interfering signals at frequencies differing from that of the wanted signal due to the onset of strong
non-linear behaviour
NOTE 1: In the present document the overload level is determined by the onset of picture degradation.
NOTE 2: Above the overloading level the receiver will behave in a non-linear way, but does not necessarily fail
immediately depending on the receiver and interference characteristics.
sensitivity: maximum usable sensitivity is defined as the minimum receiver Radio Frequency (RF) input signal level or
field strength able to produce a specified analogue SINAD ratio or Bit Error Ratio (BER), or other specified output
performance which depends on this input signal level
NOTE: In the present document receiver sensitivity is determined by the onset of picture degradation.
3.2 Symbols
For the purposes of the present document, the following symbols apply:
C Wanted signal
G Coupling Gain
C
I Interferer signal
I Licensed power
lic
I Long term rms power
rms
P Received UE interference power
RX_UE
P UE transmitted power
UE
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 303 340 V1.1.2 (2016-09)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ACE Active Constellation Extension
ACLR Adjacent Channel Leakage power Ratio
ACS Adjacent Channel Selectivity
AGC Automatic Gain Control
BER Bit Error Ratio
BS Base Station for mobile communications
CEPT European Conference of Postal and Telecommunications Administrations
DTG UK Digital TV Group
DTT Digital Terrestrial Television
DVB-T Digital Video Broadcast Terrestrial - first generation [i.4]
DVB-T2 Digital Video Broadcast Terrestrial - second generation [i.5]
FEC Forward Error Correction
FEF Future Extension Frame
FFT Fast Fourier Transform
HEM High Efficiency Mode
ISSY Input Stream SYnchronizer
QAM Quadrature Amplitude Modulation
LAPR Licensed to Average Power Ratio
NOTE: This is the ratio of the licensed power (described above) to the long term rms power (described above) of
the signal.
LDPC Low Density Parity Check (codes)
LTE Long Term Evolution
PAPR Peak to Average Power Ratio
PLP Physical Layer Pipe
64-QAM 64-ary Quadrature Amplitude Modulation
256-QAM 256-ary Quadrature Amplitude Modulation
RF Radio Frequency
SINAD (Signal + Noise + Distortion)/(Noise + Distortion) ratio
SISO Single Input Single Output (meaning one transmitting and one receiving antenna)
TFS Time-Frequency Slicing
UE User Equipment for mobile communications
NOTE: Example handsets, dongles, etc.
UHF Ultra High Frequency
VHF Very High Frequency
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the manufacturer. The equipment shall comply with all the technical
requirements of the present document at all times when operating within the boundary limits of the declared operational
environmental profile.
NOTE: The applicability of the different tests as defined in annex E may vary depending upon the selected
country profile.
ETSI
---------------------- Page: 9 ----------------------
10 ETSI EN 303 340 V1.1.2 (2016-09)
4.2 Conformance requirements
4.2.1 DVB-T and DVB-T2 configurations for testing
Representative DVB-T and DVB-T2 configurations used for conformance specification and testing are shown in
tables 2 and 3. These are used in the Nordig specification test plan [i.1].
Table 2: DVB-T configuration
Parameter Value for "7 MHz" VHF tests Value for "8 MHz" UHF tests
Bandwidth 6,66 MHz 7,61 MHz
FFT size 8K 8K
Modulation 64-QAM 64-QAM
Hierarchy Non-Hierarchical Non-Hierarchical
Guard interval 1/4 1/4
Code rate 2/3 2/3
Channel Bandwidth 7 MHz 8 MHz
Table 3: DVB-T2 configuration
Parameter Value for "7 MHz" VHF tests Value for "8 MHz" UHF tests
Bandwidth 6,66 MHz 7,77 MHz
FFT 32k 32k
Carrier mode Normal Extended
SISO/MISO SISO SISO
Guard Interval 1/16 1/16
Version 1.2.1 1.2.1
Number of symbols/frame (L ) 42 62
f
Pilot pattern PP4 PP4
TFS No No
FEF Not used Not used
Auxiliary streams Not used Not used
Subslices / T2 frame 1 1
Frames / Superframe 2 2
L1 post FEC type 16k LDPC (see note 1) 16k LDPC (see note 1)
L1 repetition 0 0
L1 post extension No No
L1 post modulation 64 QAM 64-QAM
L1 post scrambling None None
L1_ACE_MAX 0 (see note 2) 0 (see note 2)
L1 bias balancing cells No No
PAPR L1-ACE & TR (see note 3) L1-ACE & TR (see note 3)
PAPR: V 3,1 V (see note 1) 3,1 V (see note 1)
clip
PAPR: Number of iterations 10 (see note 1) 10 (see note 1)
TS
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.