SIST EN 12952-13:2003
(Main)Water-tube boilers and auxiliary installations - Part 13: Requirements for flue gas cleaning systems
Water-tube boilers and auxiliary installations - Part 13: Requirements for flue gas cleaning systems
This European Standard applies to the design of equipment for boiler plants to reduce air pollutants in the flue gases.
NOTE The effects of explosion are not considered in this Part of the is European Standard.
Wasserrohrkessel und Anlagenkomponenten - Teil 13: Anforderungen an Rauchgasreinigungsanlagen
Diese EN-Norm gilt für die Auslegung der Ausrüstung von Kesselanlagen zur Verminderung von luftverunreinigenden Stoffen in Rauchgasen. Die Auswirkungen einer Explosion werden in diesem Teil der Norm nicht berücksichtigt.
Chaudieres a tubes d'eau et installations auxiliaires - Partie 13: Exigences pour les systemes de traitement des fumées
La présente partie de cette Norme européenne s'applique a la conception d'un équipement de chaufferie destiné a réduire les polluants atmosphériques dans les gaz de combustion.
NOTE Les effets d'une explosion ne sont pas pris en considération dans la présente partie de cette norme européenne.
Vodocevni kotli in pomožne napeljave - 13. del: Zahteve za čistilne naprave dimnih plinov
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SOLQRYWasserrohrkessel und Anlagenkomponenten - Teil 13: Anforderungen an RauchgasreinigungsanlagenChaudieres a tubes d'eau et installations auxiliaires - Partie 13: Exigences pour les systemes de traitement des fuméesWater-tube boilers and auxiliary installations - Part 13: Requirements for flue gas cleaning systems27.060.30Grelniki vode in prenosniki toploteBoilers and heat exchangersICS:Ta slovenski standard je istoveten z:EN 12952-13:2003SIST EN 12952-13:2003en01-december-2003SIST EN 12952-13:2003SLOVENSKI
STANDARD
SIST EN 12952-13:2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12952-13March 2003ICS 27.040; 27.060.30English versionWater-tube boilers and auxiliary installations - Part 13:Requirements for flue gas cleaning systemsChaudières à tubes d'eau et installations auxiliaires - Partie13: Exigences pour les systèmes de traitement des fuméesWasserrohrkessel und Anlagenkomponenten - Teil 13:Anforderungen an RauchgasreinigungsanlagenThis European Standard was approved by CEN on 27 December 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12952-13:2003 ESIST EN 12952-13:2003
EN 12952-13:2003 (E)2ContentspageForeword.31Scope.42Normative references.43Design, calculation, construction and manufacture.44Equipment and erection.55Inspection and testing.75.1Inspection of workmanship and leakage testing.75.2Final inspection before putting into operation.76Operating manual and instructions.7Annex A (informative)
Guidance on operation matters.8Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or otherprovisions of EU Directives.9Bibliography.10SIST EN 12952-13:2003
EN 12952-13:2003 (E) 3ForewordThis document (EN 12952-13:2003) has been prepared by Technical Committee CEN/TC 269 "Shell and water-tube boilers", the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by September 2003, and conflicting national standards shall be withdrawn at the lat-est by September 2003.This document has been prepared under a mandate given to CEN by the European Commission and the EuropeanFree Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.The European Standard EN 12952 concerning water-tube boilers and auxiliary installations consists of the followingparts:¾ Part 1: General¾ Part 2: Materials for pressure parts of boilers and accessories¾ Part 3: Design and calculation for pressure parts¾ Part 4: In-service boiler life expectancy calculations¾ Part 5: Workmanship and construction of pressure parts of the boiler¾ Part 6: Inspection during construction, documentation and marking of pressure parts of the boiler¾ Part 7: Requirements for equipment for the boiler¾ Part 8: Requirements for firing systems for liquid and gaseous fuels for the boiler¾ Part 9: Requirements for firing systems for pulverized solid fuels for the boiler¾ Part 10: Requirements for safeguards against excessive pressure¾ Part 11: Requirements for limiting devices and safety circuits of the boiler and accessories¾ Part 12: Requirements for boiler feedwater and boiler water quality¾ Part 13: Requirements for flue gas cleaning systems¾ Part 14: Requirements for flue gas DENOX-systems¾ Part 15: Acceptance tests¾ Part 16: Requirements for grate and fluidized bed firing systems for solid fuels for the boilerCR 12952-17, Water boilers and auxiliary installations - Part 17: Guideline for the involvement of an inspectionbody independent of the manufacturerAlthough, these parts may be obtained separately, it should be recognised that the parts are inter-dependent. Assuch, the design and manufacture of water-tube boilers requires the application of more than one part in order forthe requirements of the European Standard to be satisfactorily fulfilled.NOTEParts 4 and 15 are not applicable during the design, construction and installation stages.Annex A is informative.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun-tries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.SIST EN 12952-13:2003
EN 12952-13:2003 (E)41 ScopeThis part of this European Standard applies to the design of equipment for boiler plants to reduce air pollutants inthe flue gases.NOTEThe effects of explosion are not considered in this part of this European Standard.2 Normative referencesThis European Standard incorporates, by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 12952-8, Water-tube boilers and auxiliary installations – Part 8: Requirements for firing systems for liquid andgaseous fuels for the boilerprEN 12952-14, Water-tube boilers and auxiliary installations – Part 14: Requirements for flue gas DENOX-systemsEN 13445 (all parts), Unfired pressure vessels.prEN 50156-1:1997, Electrical equipment for furnaces and ancillary equipment – Part 1: Requirements for applica-tion design and installation.3 Design, calculation, construction and manufacture3.1The plant components, vessels, absorbers, DENOX reactors, scrubbers, heat exchangers, pipework, ducts,expansion joints, shut-off devices, blanking disks and other related equipment shall be designed such that they willsafely withstand the mechanical loadings from internal pressure, vacuum, if any, dead weight and additional forcese.g. expansion joint working spring rates, at the intended operating temperature and for the service lifetime. Pres-sures and loadings resulting from operating upset conditions and their consequences shall be considered sepa-rately. In such cases, the safety factor referred to the pertinent yield stress shall be at least 1.0.Temperatures below dew point, if any, and the consequences arising therefrom shall be prevented by suitablemeasures or by proper selection of materials. Additional effects such as corrosion/erosion attack by otherchemicals in the flue gas may be considered by wall thickness allowances, if required. The suitability of plantcomponents containing water-polluting substances shall comply with European Standards (e.g. prEN 12285).3.2The design shall be based on the load assumptions of EN 13445 unless deviations from these assumptionsoccur locally.For additional loadings not covered by the above mentioned standard the respective values shall be taken from thedesign data, in which case distinction has to be made between normal and abnormal operating load conditions.3.3Unfired pressure vessels included in the system shall be designed and manufactured in accordance withEN 13445.3.4The design shall assume that under any operating condition the flue gas pressure is not higher or lower thanthe value used in the design. Particular consideration of the damper positions and the heads of pumps and fansshall be taken into account.3.5The design of the components shall take into account the requirements for corrosion resistant materials, foritems such as linings and coatings.3.6Structural components of the flue-gas cleaning plant shall meet the relevant European Standards (e.g.ENV 1993, ENV 1994). Fire-protection requirements shall be taken into account.SIST EN 12952-13:2003
EN 12952-13:2003 (E) 53.7Firing systems for reheating the flue-gas (e.g. flat flame burners) shall be designed in accordance withEN 12952-8.4 Equipment and erection4.1Suitable control equipment shall be provided to prevent pressure or temperature excursions:a) in the flue gas path, e. g. by cut-out of the firing system or changeover to the flue-gas bypass systemb) in isolated sections when¾ supplementary firing systems for flue-gas reheating;¾ seal-air fans on isolating dampers;¾ fans are operating.c) in the case of failure of or operating problems on¾ equipment, e. g. fans, heat exchangers, back-up burners;¾ dampers.Electrical drive units having safety functions shall meet the requirements of prEN 50156-1.4.2Drains shall be provided to permit the discharge of any condensate formed below the dew point temperature.4.3Access openings, e.g. manhole doors, shall be provided in vessels, ducts and similar equipment to facilitatethe required maintenance work.4.4Access openings shall wherever possible have the following dimensions¾ an internal diameter of at least 800 mm or¾ a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.