SIST EN 61753-121-2:2018
(Main)Fibre optic interconnecting devices and passive components - Performance standards - Part 121-2: Simplex and duplex cords with singlemode fibre and cylindrical ferrule connectors for category C - Controlled environment (IEC 61753-121-2:2017)
Fibre optic interconnecting devices and passive components - Performance standards - Part 121-2: Simplex and duplex cords with singlemode fibre and cylindrical ferrule connectors for category C - Controlled environment (IEC 61753-121-2:2017)
IEC 61753-121-2:2010(E) specifies the test requirements for finished cable assemblies for use as patchcords, work area cords and equipment cords for applications in a controlled (C) environment according to IEC 61753-1, where the connectors already comply, with the Category C requirements of IEC 61753-1. The assemblies consist of simplex or duplex fibre optic cable terminated at each end of the cable with non-angled (PC) or angled (APC) polished single-mode fibre optic connectors with cylindrical ferrules. The wavelength of operation is between 1 260 nm and 1 625 nm.
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Betriebsverhalten - Teil 121-2: Simplex- und Duplexkabel mit Einmoden-Lichtwellenleiter-Steckverbindern mit zylindrischen Ferrulen für die Kategorie C - Kontrollierte Umgebung (IEC 61753-121-2:2017)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Norme de qualité de fonctionnement - Partie 121-2: Cordons simplex et duplex avec fibres unimodales, munis de connecteurs à férule cylindrique pour catégorie C - Environnement contrôlé (IEC 61753-121-2:2017)
La CEI 61753-121-2:2010 spécifie les exigences relatives aux essais appliqués aux cordons finis utilisés en tant que cordons de brassage, cordons de zone de travail et cordons d'équipement, en vue d'applications dans un environnement contrôlé (C) conformément à la CEI 61753-1, là où les connecteurs sont déjà conformes, conjointement avec les exigences de la catégorie C de la CEI 61753-1. Les ensembles sont constitués de câbles à fibres optiques simplex ou duplex munis à chaque extrémité du câble de connecteurs à fibres optiques unimodales polies sans angle (PC) ou à angle (APC), comportant des férules cylindriques. La longueur d'onde de fonctionnement est comprise entre 1 260 nm et 1 625 nm.
Optični spojni elementi in pasivne komponente - Tehnični standardi - 121-2. del: Simpleksne in dupleksne vrvice z enorodnim optičnim vlaknom ter cilindričnimi tulčastimi konektorji za kategorijo C - Nadzorovano okolje (IEC 61753-121-2:2017)
Standard IEC 61753-121-2:2010(E) določa preskusne zahteve za dokončane kabelske sklope, ki se uporabljajo kot stikalni kabli, kabli na delovnem območju in kabli opreme za uporabo v nadzorovanem (C) območju skladno s standardom IEC 61753-1, pri čemer so konektorji skladni z zahtevami kategorije C standarda IEC 61753-1. Sklopi so sestavljeni iz simpleksnih in dupleksnih optičnih kablov, ki so na vsaki strani zaključeni z nekotnimi (PC) ali kotnimi (APC) enorodnimi optičnimi konektorji s cilindričnimi tulkami. Delovna valovna dolžina je med 1260 nm in 1625 nm.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 61753-121-2:2018
01-januar-2018
1DGRPHãþD
SIST EN 61753-121-2:2010
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH7HKQLþQLVWDQGDUGLGHO
6LPSOHNVQHLQGXSOHNVQHYUYLFH]HQRURGQLPRSWLþQLPYODNQRPWHUFLOLQGULþQLPL
WXOþDVWLPLNRQHNWRUML]DNDWHJRULMR&1DG]RURYDQRRNROMH ,(&
Fibre optic interconnecting devices and passive components - Performance standards -
Part 121-2: Simplex and duplex cords with singlemode fibre and cylindrical ferrule
connectors for category C - Controlled environment (IEC 61753-121-2:2017)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Betriebsverhalten - Teil
121-2: Simplex- und Duplexkabel mit Einmoden-Lichtwellenleiter-Steckverbindern mit
zylindrischen Ferrulen für die Kategorie C - Kontrollierte Umgebung (IEC 61753-121-
2:2017)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Norme de qualité
de fonctionnement - Partie 121-2: Cordons simplex et duplex avec fibres unimodales,
munis de connecteurs à férule cylindrique pour catégorie C - Environnement contrôlé
(IEC 61753-121-2:2017)
Ta slovenski standard je istoveten z: EN 61753-121-2:2017
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 61753-121-2:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 61753-121-2:2018
---------------------- Page: 2 ----------------------
SIST EN 61753-121-2:2018
EUROPEAN STANDARD EN 61753-121-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2017
ICS 33.180.20 Supersedes EN 61753-121-2:2010
English Version
Fibre optic interconnecting devices and passive components -
Performance standard - Part 121-2: Simplex and duplex cords
with single-mode fibre and cylindrical ferrule connectors for
category C - Controlled environment
(IEC 61753-121-2:2017)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Norme de performance - Bauteile -Betriebsverhalten - Teil 121-2: Simplex- und
Partie 121-2: Cordons simplex et duplex avec fibres Duplexkabel mit Einmoden-Lichtwellenleiter-
unimodales, munis de connecteurs à férule cylindrique pour Steckverbindern mit zylindrischen Ferrulen für die Kategorie
catégorie C - Environnement contrôlé C - Kontrollierte Umgebung
(IEC 61753-121-2:2017) (IEC 61753-121-2:2017)
This European Standard was approved by CENELEC on 2017-06-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61753-121-2:2017 E
---------------------- Page: 3 ----------------------
SIST EN 61753-121-2:2018
EN 61753-121-2:2017
European foreword
The text of document 86B/4076/FDIS, future edition 2 of IEC 61753-121-2, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN 61753-121-2:2017.
The following dates are fixed:
(dop) 2018-04-20
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2020-10-20
standards conflicting with the
document have to be withdrawn
This document supersedes EN 61753-121-2:2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61753-121-2:2017 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60794-1-2:2017 NOTE Harmonized as EN 60794-1-2:2017 (not modified).
IEC 60794-2 NOTE Harmonized as EN 60794-2.
IEC 61300 Series NOTE Harmonized as EN 61300 Series.
IEC 61753 Series NOTE Harmonized as EN 61753 Series.
IEC 61756-1 NOTE Harmonized as EN 61756-1.
2
---------------------- Page: 4 ----------------------
SIST EN 61753-121-2:2018
EN 61753-121-2:2017
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60793-2-50 - Optical fibres - EN 60793-2-50 -
Part 2-50: Product specifications -
Sectional specification for class B single-
mode fibres
IEC 60794-2-50 - Optical fibre cables - EN 60794-2-50 -
Part 2-50: Indoor cables - Family
specification for simplex and duplex cables
for use in terminated cable assemblies
IEC 60794-2-51 - Optical fibre cables - EN 60794-2-51 -
Part 2-51: Indoor cables - Detail
specification for simplex and duplex cables
for use in cords for controlled environment
IEC 61300-1 - Fibre optic interconnecting devices and EN 61300-1 -
passive components - Basic test and
measurement procedures -
Part 1: General and guidance
IEC 61300-2-4 - Fibre optic interconnecting devices and EN 61300-2-4 -
passive components - Basic test and
measurement procedures -
Part 2-4: Tests - Fibre/cable retention
IEC 61300-2-22 - Fibre optic interconnecting devices and EN 61300-2-22 -
passive components - Basic test and
measurement procedures -
Part 2-22: Tests - Change of temperature
IEC 61300-2-42 - Fibre optic interconnecting devices and EN 61300-2-42 -
passive components - Basic test and
measurement procedures - Part 2-42:
Tests - Static side load for strain relief
IEC 61300-2-44 - Fibre optic interconnecting devices and EN 61300-2-44 -
passive components - Basic test and
measurement procedures -
Part 2-44: Tests - Flexing of the strain relief
of fibre optic devices
3
---------------------- Page: 5 ----------------------
SIST EN 61753-121-2:2018
EN 61753-121-2:2017
Publication Year Title EN/HD Year
IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures -
Part 3-1: Examinations and measurements
- Visual examination
IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures -
Part 3-3: Examinations and measurements
- Active monitoring of changes in
attenuation and return loss
IEC 61300-3-6 - Fibre optic interconnecting devices and EN 61300-3-6 -
passive components - Basic test and
measurement procedures -
Part 3-6: Examinations and measurements
- Return loss
IEC 61300-3-22 - Fibre optic interconnecting devices and EN 61300-3-22 -
passive components - Basic test and
measurement procedures -
Part 3-22: Examinations and
measurements - Ferrule compression force
IEC 61300-3-25 - Fibre optic interconnecting devices and EN 61300-3-25 -
passive components - Basic test and
measurement procedures -
Part 3-25: Examinations and
measurements - Concentricity of non-
angled ferrules and non-angled ferrules
with fibre installed
IEC 61300-3-26 - Fibre optic interconnecting devices and EN 61300-3-26 -
passive components - Basic test and
measurement procedures -
Part 3-26: Examinations and
measurements - Measurement of the
angular misalignment between fibre and
ferrule axes
IEC 61300-3-28 - Fibre optic interconnecting devices and EN 61300-3-28 -
passive components - Basic test and
measurement procedures -
Part 3-28: Examinations and
measurements - Transient loss
IEC 61300-3-34 - Fibre optic interconnecting devices and EN 61300-3-34 -
passive components - Basic test and
measurement procedures -
Part 3-34: Examinations and
measurements - Attenuation of random
mated connectors
IEC 61300-3-35 - Fibre optic interconnecting devices and EN 61300-3-35 -
passive components - Basic test and
measurement procedures -
Part 3-35: Examinations and
measurements - Visual inspection of fibre
optic connectors and fibre-stub
transceivers
4
---------------------- Page: 6 ----------------------
SIST EN 61753-121-2:2018
EN 61753-121-2:2017
Publication Year Title EN/HD Year
IEC 61300-3-47 - Fibre optic interconnecting devices and EN 61300-3-47 -
passive components - Basic test and
measurement procedures -
Part 3-47: Examinations and
measurements - Endface geometry of
PC/APC spherically polished ferrules using
interferometry
IEC 61753-1 - Fibre optic interconnecting devices and EN 61753-1 -
passive components performance standard
- Part 1: General and guidance for
performance standards
IEC 61753-021-2 - Fibre optic interconnecting devices and EN 61753-021-2 -
passive components performance standard
- Part 021-2: Grade C/3 single-mode fibre
optic connectors for category C -
Controlled environment
IEC 61754 Series Fibre optic interconnecting devices and EN 61754 Series
passive components - Fibre optic
connector interfaces
IEC 61755 Series Fibre optic interconnecting devices and EN 61755 Series
passive components - connector optical
interfaces
IEC/TR 61931 - Fibre optic - Terminology - -
5
---------------------- Page: 7 ----------------------
SIST EN 61753-121-2:2018
---------------------- Page: 8 ----------------------
SIST EN 61753-121-2:2018
IEC 61753-121-2
®
Edition 2.0 2017-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Performance
standard –
Part 121-2: Simplex and duplex cords with single-mode fibre and cylindrical
ferrule connectors for category C – Controlled environment
Dispositifs d’interconnexion et composants passifs fibroniques – Norme de
performance –
Partie 121-2: Cordons simplex et duplex avec fibres unimodales, munis de
connecteurs à férule cylindrique pour catégorie C – Environnement contrôlé
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-4390-9
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 9 ----------------------
SIST EN 61753-121-2:2018
– 2 – IEC 61753-121-2:2017 © IEC 2017
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Description . 8
4.1 General . 8
4.2 Optical fibres . 8
4.3 Cable design and construction . 8
4.4 Optical connectors . 8
4.4.1 Mechanical connectivity . 8
4.4.2 Optical performance requirements . 8
4.4.3 Connector set performance requirements . 8
4.5 Cable bend radius . 8
5 Tests . 8
5.1 General . 8
5.2 Measurement wavelengths . 9
5.3 Device under test . 9
5.4 Test report . 9
6 Test procedure . 9
6.1 General . 9
6.2 Visual examination . 9
6.3 Fibre optic connector plug end face . 9
6.4 Optical performance requirements . 10
6.5 Environmental performance requirements . 11
6.6 Mechanical performance requirements . 12
Annex A (normative) Sample size requirements . 14
Annex B (normative) Visual examination of outer cable sheath movement . 15
B.1 Scope . 15
B.2 Preparation of the DUT and initial visual examination . 15
B.3 Final visual examination of outer cable sheath movement . 15
Annex C (normative) Change of temperature . 16
Bibliography . 17
Figure B.1 – Initial marking of the cable sheath . 15
Figure B.2 – Final visual examination. 15
Figure C.1 – Change of temperature test configuration . 16
Table 1 – Wavelengths for attenuation and return loss measurements . 9
Table 2 – Visual examination requirements . 9
Table 3 – End face requirements . 10
Table 4 – Optical performance requirements . 10
Table 5 – Environmental performance requirements . 11
Table 6 – Mechanical performance requirements . 12
Table A.1 – Sample size requirements . 14
---------------------- Page: 10 ----------------------
SIST EN 61753-121-2:2018
IEC 61753-121-2:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
PERFORMANCE STANDARD –
Part 121-2: Simplex and duplex cords with single-mode
fibre and cylindrical ferrule connectors for category C –
Controlled environment
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61753-121-2 has been prepared by subcommittee 86B: Fibre optic
interconnecting devices and passive components, of IEC technical committee 86: Fibre optics.
This second edition cancels and replaces the first edition published in 2010. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) merge an optical performance requirement of a reference cord;
b) delete Annexes D and E due to updated relevant standard document;
---------------------- Page: 11 ----------------------
SIST EN 61753-121-2:2018
– 4 – IEC 61753-121-2:2017 © IEC 2017
c) modify the whole document structure according to the latest ISO/IEC Directives.
The text of this International Standard is based on the following documents:
FDIS Report on voting
86B/4076/FDIS 86B/4084/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of IEC 61753 series, published under the general title Fibre optic
interconnecting devices and passive components – Performance standard, can be found on
the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 12 ----------------------
SIST EN 61753-121-2:2018
IEC 61753-121-2:2017 © IEC 2017 – 5 –
FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
PERFORMANCE STANDARD –
Part 121-2: Simplex and duplex cords with single-mode
fibre and cylindrical ferrule connectors for category C –
Controlled environment
1 Scope
This part of IEC 61753 specifies the test requirements for cords including reference cords
used in a controlled (Category C) environment according to IEC 61753-1, where the
connectors already comply with the Category C requirements of IEC 61753-1. The tests
selected are a subset of the connector tests from IEC 61753-1 appropriate for requalification
with additional requirements relevant to cords and the connector/cable interface.
The cords consist of simplex or duplex fibre optic cable terminated at each end of the cable
with single-mode fibre optic connector plugs with cylindrical ferrules. The operational
wavelength range is between 1 260 nm and 1 625 nm. Short length cords are used as test
samples as the attenuation of the cord and the temperature cycling performance will be
affected by longer lengths of cable. It is important that any qualification of a cord whose
length is greater than 5 m takes these factors into account.
The relevant requirements for the mechanical interface of connector sets are covered by the
IEC 61754 all parts. The relevant requirements for the optical interface of connector sets are
covered by IEC 61755 (all parts). The relevant requirements for performance of connector
sets are covered by IEC 61753 (all parts). The relevant requirements for fibres are covered by
IEC 60793-2-50. The relevant requirements for cables for cords are covered by IEC 60794-2-
50.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60793-2-50, Optical fibres – Part 2-50: Product specifications – Sectional specification for
class B single-mode fibres
IEC 60794-2-50, Optical fibre cables – Part 2-50: Indoor cables – Family specification for
simplex and duplex cables for use in terminated cable assemblies
IEC 60794-2-51, Optical fibre cables – Part 2-51: Indoor cables – Detail specification for
simplex and duplex cables for use in cords for controlled environment
IEC 61300-1, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 1: General and guidance
IEC 61300-2-4, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-4: Tests – Fibre/cable retention
---------------------- Page: 13 ----------------------
SIST EN 61753-121-2:2018
– 6 – IEC 61753-121-2:2017 © IEC 2017
IEC 61300-2-22, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 2-22: Tests – Change of temperature
IEC 61300-2-42, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 2-42: Tests – Static side load for strain relief
IEC 61300-2-44, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 2-44: Tests – Flexing of the strain relief of fibre optic
devices
IEC 61300-3-1, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-1: Examinations and measurements – Visual examination
IEC 61300-3-3, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-3: Examinations and measurements – Active monitoring of
changes in attenuation and return loss
IEC 61300-3-6, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-6: Examinations and measurements – Return loss
IEC 61300-3-22, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-22: Examinations and measurements – Ferrule
compression force
IEC 61300-3-25, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-25: Examinations and measurements – Concentricity
of non-angled ferrules and non-angled ferrules with fibre installed
IEC 61300-3-26, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-26: Examinations and measurements – Measurement
of the angular misalignment between fibre and ferrule axes
IEC 61300-3-28, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-28: Examinations and measurements – Transient loss
IEC 61300-3-34, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-34: Examinations and measurements – Attenuation of
random mated connectors
IEC 61300-3-35, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-35: Examinations and measurements – Visual
inspection of fibre optic connectors and fibre-stub transceivers
IEC 61300-3-47, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-47: Examinations and measurements – End face
geometry of PC/APC spherically polished ferrules using interferometry
IEC 61753-1, Fibre optic interconnecting devices and passive components – Performance
standard – Part 1: General and guidance for performance standards
IEC 61753-021-2, Fibre optic interconnecting devices and passive components – Performance
standard – Part 021-2: Grade C/3 single-mode fibre optic connectors for category C –
Controlled environment
IEC 61754 (all parts), Fibre optic interconnecting devices and passive components – Fibre
optic connector interfaces
---------------------- Page: 14 ----------------------
SIST EN 61753-121-2:2018
IEC 61753-121-2:2017 © IEC 2017 – 7 –
IEC 61755 (all parts), Fibre optic interconnecting devices and passive components –
Connector optical interfaces
IEC TR 61931, Fibre optic – Terminology
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC TR 61931 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
terminated cable assembly
fibre optic cable terminated with any passive fibre optic component
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.