SIST EN 13523-5:2014
(Main)Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)
Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)
EN 13523-5 specifies the procedure for determining the resistance to cracking and/or pick-off on rapid deformation of an organic coating on a metallic substrate in terms of energy which the specimen will withstand.
Bandbeschichtete Metalle - Prüfverfahren - Teil 5: Widerstandsfähigkeit gegen schnelle Verformung (Schlagprüfung)
Dieser Teil von EN 13523 legt das Verfahren zum Bestimmen der Widerstandsfähigkeit einer organischen Beschichtung auf einem metallischen Substrat gegen Rissbildung und/oder Ablösen bei schneller Verformung fest.
Tôles prélaquées - Méthodes d'essai - Partie 5 : Résistance à la déformation rapide (essai de choc)
La présente partie de l’EN 13523 décrit la méthode de détermination de la résistance à la fissuration et/ou à l’arrachement en cas de déformation rapide d’une peinture organique sur un subjectile métallique, en termes d’énergie à laquelle l’éprouvette va résister.
Prevlečene kovine, ki se navijajo - Preskusne metode - 5. del: Odpornost proti hitri deformaciji (preskus z udarcem)
Standard EN 13523-5 določa postopek za določanje odpornosti proti nastanku razpok in/ali pokanju pri hitri deformaciji organske prevleke na kovinski podlagi v smislu energije, ki jo preskusni vzorec lahko prenese.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bandbeschichtete Metalle - Prüfverfahren - Teil 5: Widerstandsfähigkeit gegen schnelle Verformung (Schlagprüfung)Tôles prélaquées - Méthodes d'essai - Partie 5 : Résistance à la déformation rapide (essai de choc)Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)25.220.60Organske prevlekeOrganic coatings17.040.20Lastnosti površinProperties of surfacesICS:Ta slovenski standard je istoveten z:EN 13523-5:2014SIST EN 13523-5:2014en,fr,de01-september-2014SIST EN 13523-5:2014SLOVENSKI
STANDARDSIST EN 13523-5:20021DGRPHãþD
SIST EN 13523-5:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13523-5
June 2014 ICS 25.220.60 Supersedes EN 13523-5:2001English Version
Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)
Tôles prélaquées - Méthodes d'essai - Partie 5 : Résistance à la déformation rapide (essai de choc)
Bandbeschichtete Metalle - Prüfverfahren - Teil 5: Widerstandsfähigkeit gegen schnelle Verformung (Schlagprüfung) This European Standard was approved by CEN on 7 May 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13523-5:2014 ESIST EN 13523-5:2014
EN 13523-5:2014 (E) 2 Contents Page Foreword .3 1 Scope .5 2 Normative references .5 3 Terms and definitions .5 4 Principle .5 5 Apparatus and materials .5 6 Sampling .5 7 Test panels .6 8 Procedure .6 9 Expression of results .6 10 Precision .6 11 Test report .6 Annex A (informative)
Conversion of units .8 Bibliography .9
SIST EN 13523-5:2014
EN 13523-5:2014 (E) 3 Foreword This document (EN 13523-5:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn at the latest by December 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13523-5:2001. The main technical changes are: a) the limitation in the scope to coatings having a thickness of 60 µm maximum was deleted; b) a remark on preconditioning was added; c) details on the brands of the tape used were added; d) in addition to use a × 10 magnifying glass, the evaluation shall be carried out with normal corrected vision. EN 13523, Coil coated metals — Test methods, consists of the following parts: — Part 0: General introduction — Part 1: Film thickness — Part 2: Gloss — Part 3: Colour difference — Instrumental comparison — Part 4: Pencil hardness — Part 5: Resistance to rapid deformation (impact test) — Part 6: Adhesion after indentation (cupping test) — Part 7: Resistance to cracking on bending (T-bend test) — Part 8: Resistance to salt spray (fog) — Part 9: Resistance to water immersion — Part 10: Resistance to fluorescent UV radiation and water condensation
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bandbeschichtete Metalle - Prüfverfahren - Teil 5: Widerstandsfähigkeit gegen schnelle Verformung (Schlagprüfung)Tôles prélaquées - Méthodes d'essai - Partie 5 : Résistance à la déformation rapide (essai de choc)Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)25.220.60Organske prevlekeOrganic coatings17.040.20Lastnosti površinProperties of surfacesICS:Ta slovenski standard je istoveten z:FprEN 13523-5kSIST FprEN 13523-5:2014en,fr,de01-marec-2014kSIST FprEN 13523-5:2014SLOVENSKI
STANDARD
kSIST FprEN 13523-5:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 13523-5
February 2014 ICS 25.220.60 Will supersede EN 13523-5:2001English Version
Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)
Tôles prélaquées - Méthodes d'essai - Partie 5 : Résistance à la déformation rapide (essai de choc)
Bandbeschichtete Metalle - Prüfverfahren - Teil 5: Widerstandsfähigkeit gegen schnelle Verformung (Schlagprüfung) This draft European Standard is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee CEN/TC 139.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN 13523-5:2014 EkSIST FprEN 13523-5:2014
FprEN 13523-5:2014 (E) 2 Contents Page Foreword .3 1 Scope .5 2 Normative references .5 3 Terms and definitions .5 4 Principle .5 5 Apparatus and materials .5 6 Sampling .6 7 Test panels .6 8 Procedure .6 9 Expression of results .6 10 Precision .6 11 Test report .7 Annex A (informative) Conversion of units .8 Bibliography .9
kSIST FprEN 13523-5:2014
FprEN 13523-5:2014 (E) 3 Foreword This document (FprEN 13523-5:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This document is currently submitted to the Formal Vote. This document will supersede EN 13523-5:2001. The main technical changes are: a) the limitation in the scope to coatings having a thickness of 60 µm maximum was deleted; b) a remark on preconditioning was added; c) details on the brands of the tape used were added; d) in addition to use a × 10 magnifying glass, the evaluation shall be carried out with normal corrected vision. EN 13523, Coil coated metals — Test methods, consists of the following parts: — Part 0: General introduction — Part 1: Film thickness — Part 2: Gloss — Part 3: Colour difference — Instrumental comparison — Part 4: Pencil hardness — Part 5: Resistance to rapid deformation (impact test) — Part 6: Adhesion after indentation (cupping test) — Par
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.