iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13523-5:2014

(Main)

Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)

Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)

This part of EN 13523 specifies the procedure for determining the resistance to cracking and/or pick-off on rapid deformation of an organic coating on a metallic substrate in terms of energy which the specimen will withstand.

Bandbeschichtete Metalle - Prüfverfahren - Teil 5: Widerstandsfähigkeit gegen schnelle Verformung (Schlagprüfung)

Dieser Teil von EN 13523 legt das Verfahren zum Bestimmen der Widerstandsfähigkeit einer organischen Beschichtung auf einem metallischen Substrat gegen Rissbildung und/oder Ablösen bei schneller Verformung fest.

Tôles prélaquées - Méthodes d'essai - Partie 5 : Résistance à la déformation rapide (essai de choc)

La présente partie de l’EN 13523 décrit la méthode de détermination de la résistance à la fissuration et/ou à l’arrachement en cas de déformation rapide d’une peinture organique sur un subjectile métallique, en termes d’énergie à laquelle l’éprouvette va résister.

Prevlečene kovine, ki se navijajo - Preskusne metode - 5. del: Odpornost proti hitri deformaciji (preskus z udarcem)

Standard EN 13523-5 določa postopek za določanje odpornosti proti nastanku razpok in/ali pokanju pri hitri deformaciji organske prevleke na kovinski podlagi v smislu energije, ki jo preskusni vzorec lahko prenese.

General Information

Status
Published
Publication Date
17-Jun-2014
ICS
17.040.20 - Properties of surfaces
25.220.60 - Organic coatings
Technical Committee
CEN/TC 139 - Paints and varnishes
Drafting Committee
CEN/TC 139/WG 9 - Testing of coil coated metals
Current Stage
9060 - Closure of 2 Year Review Enquiry - Review Enquiry
Start Date
02-Dec-2019
Completion Date
02-Dec-2019
Ref Project
SIST EN 13523-5:2014 - Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)

Relations

Replaces
EN 13523-5:2001 - Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)
Effective Date
03-Nov-2011

Buy Standard

EN 13523-5:2014EN 13523-5:2014
PreviousNext
Standard
EN 13523-5:2014
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bandbeschichtete Metalle - Prüfverfahren - Teil 5: Widerstandsfähigkeit gegen schnelle Verformung (Schlagprüfung)Tôles prélaquées - Méthodes d'essai - Partie 5 : Résistance à la déformation rapide (essai de choc)Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)25.220.60Organske prevlekeOrganic coatings17.040.20Lastnosti površinProperties of surfacesICS:Ta slovenski standard je istoveten z:EN 13523-5:2014SIST EN 13523-5:2014en,fr,de01-september-2014SIST EN 13523-5:2014SLOVENSKI
STANDARDSIST EN 13523-5:20021DGRPHãþD



SIST EN 13523-5:2014



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13523-5
June 2014 ICS 25.220.60 Supersedes EN 13523-5:2001English Version
Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)
Tôles prélaquées - Méthodes d'essai - Partie 5 : Résistance à la déformation rapide (essai de choc)
Bandbeschichtete Metalle - Prüfverfahren - Teil 5: Widerstandsfähigkeit gegen schnelle Verformung (Schlagprüfung) This European Standard was approved by CEN on 7 May 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13523-5:2014 ESIST EN 13523-5:2014



EN 13523-5:2014 (E) 2 Contents Page Foreword .3 1 Scope .5 2 Normative references .5 3 Terms and definitions .5 4 Principle .5 5 Apparatus and materials .5 6 Sampling .5 7 Test panels .6 8 Procedure .6 9 Expression of results .6 10 Precision .6 11 Test report .6 Annex A (informative)
Conversion of units .8 Bibliography .9
SIST EN 13523-5:2014



EN 13523-5:2014 (E) 3 Foreword This document (EN 13523-5:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13523-1:2017(Main)
Coil coated metals - Test methods - Part 1: Film thickness
SIST EN 13523-1:2017

This part of the EN 13523 series specifies the procedures for determining the dry-film thickness of an organic coating on a metallic substrate (coil coating).
Four appropriate methods are given in this European Standard:
a)   magnetic induction;
b)   eddy current;
c)   micrometer;
d)   optical.
The methods are applicable only to products with smooth and flat substrates but the coating itself may be textured. In that case, for methods a) and b) the average of a series of readings will represent an average of the thickness of the organic coating, while method c) will give the maximum thickness and method d) can provide the minimum, maximum and average thickness.
Non-destructive continuous-web methods on measurement of dry-film thickness (see EN ISO 2808) are not dealt with.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-4:2014(Main)
Coil coated metals - Test methods - Part 4: Pencil hardness
SIST EN 13523-4:2014

This part of EN 13523 describes the procedure to assess the relative hardness of an organic coating on a metallic substrate, by means of pencils of known hardness.
Smooth surfaces will give more accurate results but the method is also applicable for textured surfaces. The more pronounced the texture, the greater the unreliability of results.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-13:2014(Main)
Coil coated metals - Test methods - Part 13: Resistance to accelerated ageing by the use of heat
SIST EN 13523-13:2014

This Part of EN 13523 describes the procedure for determining the behaviour of an organic coating on a metallic substrate (flat or bent specimens) when submitted to accelerated ageing by heating at a defined temperature for a defined period of time. It is not possible to test heat resistance in such way as to control all possible conditions of use. The aim of this test is therefore to furnish the basic test methods for the effect of heat. NOTE: Special applications may require that properties other than those mentioned in this part of EN 13523 be checked.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-1:2024(Main)
Coil coated metals - Test methods - Part 1: Film thickness
oSIST prEN 13523-1:2023

This document specifies the procedures for determining the dry-film thickness of an organic coating on a metallic substrate (coil coating).
Five appropriate methods are given in this document:
a)   magnetic induction;
b)   eddy current;
c)   micrometer;
d)   optical;
e)   ruggedized optical interference.
The methods are applicable only to products with smooth and flat substrates, but the coating itself can be textured. In that case, for methods a) and b), the average of a series of readings will represent an average of the thickness of the organic coating, while method c) will give the maximum thickness, method d) can provide the minimum, maximum and average thickness, and e) will give the total thickness.
Non-destructive continuous-web methods on measurement of dry-film thickness are only applicable on method a).

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-1:2017(Main)
Coil coated metals - Test methods - Part 1: Film thickness
SIST EN 13523-1:2017

This part of the EN 13523 series specifies the procedures for determining the dry-film thickness of an organic coating on a metallic substrate (coil coating).
Four appropriate methods are given in this European Standard:
a)   magnetic induction;
b)   eddy current;
c)   micrometer;
d)   optical.
The methods are applicable only to products with smooth and flat substrates but the coating itself may be textured. In that case, for methods a) and b) the average of a series of readings will represent an average of the thickness of the organic coating, while method c) will give the maximum thickness and method d) can provide the minimum, maximum and average thickness.
Non-destructive continuous-web methods on measurement of dry-film thickness (see EN ISO 2808) are not dealt with.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-4:2014(Main)
Coil coated metals - Test methods - Part 4: Pencil hardness
SIST EN 13523-4:2014

This part of EN 13523 describes the procedure to assess the relative hardness of an organic coating on a metallic substrate, by means of pencils of known hardness.
Smooth surfaces will give more accurate results but the method is also applicable for textured surfaces. The more pronounced the texture, the greater the unreliability of results.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-13:2014(Main)
Coil coated metals - Test methods - Part 13: Resistance to accelerated ageing by the use of heat
SIST EN 13523-13:2014

This Part of EN 13523 describes the procedure for determining the behaviour of an organic coating on a metallic substrate (flat or bent specimens) when submitted to accelerated ageing by heating at a defined temperature for a defined period of time. It is not possible to test heat resistance in such way as to control all possible conditions of use. The aim of this test is therefore to furnish the basic test methods for the effect of heat. NOTE: Special applications may require that properties other than those mentioned in this part of EN 13523 be checked.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-1:2024(Main)
Coil coated metals - Test methods - Part 1: Film thickness
oSIST prEN 13523-1:2023

This document specifies the procedures for determining the dry-film thickness of an organic coating on a metallic substrate (coil coating).
Five appropriate methods are given in this document:
a)   magnetic induction;
b)   eddy current;
c)   micrometer;
d)   optical;
e)   ruggedized optical interference.
The methods are applicable only to products with smooth and flat substrates, but the coating itself can be textured. In that case, for methods a) and b), the average of a series of readings will represent an average of the thickness of the organic coating, while method c) will give the maximum thickness, method d) can provide the minimum, maximum and average thickness, and e) will give the total thickness.
Non-destructive continuous-web methods on measurement of dry-film thickness are only applicable on method a).

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16739-1:2024(Main)
Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries - Part 1: Data schema (ISO 16739-1:2024)
kSIST FprEN ISO 16739-1:2024

This document represents an open international standard for information used in Building Information Modeling (BIM) that is exchanged and shared among software applications used by the various participants in the construction or facility management industry sector. This document includes definitions that cover information required for buildings and infrastructure works over their life cycle. This edition of the document added coverage of information required for infrastructure facilities including bridges, roads, railways, waterways and port facilities.
This document comprises the publication of a data schema, its documentation, the property and quantity set definitions and the mechanism of an exchange file format structure.
Definitions from this document are used to support different recognized work flows in the construction and facility management industry sector, representing information deliveries. Such information deliveries can be described according to ISO 29481.
Different implementation levels of this document can be defined to better support multiple information deliveries, they are referred to as a Model View Definition (MVD). Each MVD identifies which subset of the definitions of this document imposes requirements for implementation in software applications. Conforming software applications need to identify the model view definition they conform to when applying for software certification.
The following are within the scope of this edition of this document:
BIM exchange format definitions that are required during the life cycle phases of buildings and infrastructure:
demonstrating the need;
conception of need;
outline feasibility;
substantive feasibility study and outline financial authority;
outline conceptual design;
full conceptual design;
coordinated design;
procurement and full financial authority;
production information;
construction;
operation and maintenance.
BIM exchange format definitions that are required by the various disciplines involved within the life cycle phases:
architecture and civil engineering design;
service and utilities engineering;
structural engineering;
procurement;
construction planning;
facility and utility management;
project management;
client requirement management;
industry authorities for permits and approval.
BIM exchange format definitions including:
project structure;
physical components;
spatial components;
analysis items;
processes;
resources;
controls;
actors;
context definition.

  • Draft
    406 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17294-1:2024(Main)
Water quality - Application of inductively coupled plasma mass spectrometry (ICP-MS) - Part 1: General requirements (ISO 17294-1:2024)
kSIST FprEN ISO 17294-1:2023

This document specifies the principles of inductively coupled plasma mass spectrometry (ICP-MS) and provides general requirements for the use of this technique to determine elements in water, digests of sludges and sediments (e.g. digests of water as described in ISO 15587-1 or ISO 15587-2). Generally, the measurement is carried out in water, but gases, vapours or fine particulate matter can be introduced too. This document applies to the use of ICP-MS for aqueous solution analysis.
The ultimate determination of the elements is described in a separate International Standard for each series of elements and matrix. The individual clauses of this document refer the user to these guidelines for the basic principles of the method and the configuration of the instrument.

  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day