SIST EN 827:2006

Adhesives - Determination of conventional solids content and constant mass solids content

This European Standard specifies a method for the determination of conventional solids content and, where possible, constant mass solids content.
It is applicable to dispersion, emulsion and solvent based adhesives.

Klebstoffe - Bestimmung des Feststsoffgehaltes nach Vereinbarung und bis zur Massekonstanz

Diese Europäische Norm beschreibt ein Verfahren zur Bestimmung des Feststoffgehaltes nach Vereinbarung und, soweit dies möglich ist, bis zur Konstanz des Massegehaltes.
Das angegebene Verfahren ist anwendbar bei Dispersions-, Emulsions- und Lösemittel-Klebstoffen.

Adhésifs - Détermination de l'extrait sec conventionnel et de l'extrait sec a masse constante

La présente norme européenne prescrit une méthode de détermination de la teneur en extrait sec
conventionnel d'un adhésif et, si possible, de sa teneur en extrait sec a masse constante.
Il s'applique aux adhésifs en dispersion, en émulsion et a base de solvants.

Lepila – Določevanje suhega ostanka in suhega ostanka po sušenju do konstantne mase

General Information

• Status: Published
• Publication Date: 31-Mar-2006
• ICS: 83.180 - Adhesives
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Apr-2006
• Due Date: 01-Apr-2006
• Completion Date: 01-Apr-2006
• Ref Project: EN 827:2005 - Adhesives - Determination of conventional solids content and constant mass solids content

Relations

• Replaces: SIST EN 827:1998 - Adhesives - Determination of conventional solids content and constant mass solids content
• Effective Date: 01-Apr-2006

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 827:2006
01-april-2006
Nadomešča:
SIST EN 827:1998
Lepila – Določevanje suhega ostanka in suhega ostanka po sušenju do
konstantne mase
Adhesives - Determination of conventional solids content and constant mass solids
content
Klebstoffe - Bestimmung des Feststsoffgehaltes nach Vereinbarung und bis zur
Massekonstanz
Adhésifs - Détermination de l'extrait sec conventionnel et de l'extrait sec a masse
constante
Ta slovenski standard je istoveten z: EN 827:2005
ICS:
83.180 Lepila Adhesives
SIST EN 827:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 827:2006

---------------------- Page: 2 ----------------------
SIST EN 827:2006
EUROPEAN STANDARD
EN 827
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2005
ICS 83.180 Supersedes EN 827:1994
English Version
Adhesives - Determination of conventional solids content and
constant mass solids content
Adhésifs - Détermination de l'extrait sec conventionnel et Klebstoffe - Bestimmung des Feststsoffgehaltes nach
de l'extrait sec à masse constante Vereinbarung und bis zur Massekonstanz
This European Standard was approved by CEN on 21 November 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 827:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 827:2006
EN 827:2005 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions.4
4 Safety .4
5 Apparatus .5
6 Sampling.5
7 Procedure .5
8 Expression of results.7
9 Test report .8

2

---------------------- Page: 4 ----------------------
SIST EN 827:2006
EN 827:2005 (E)
Foreword
This European Standard (EN 827:2005) has been prepared by Technical Committee CEN/TC 193
“Adhesives”, the secretariat of which is held by AENOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2006, and conflicting national standards shall be withdrawn at
the latest by June 2006.
This European Standard supersedes EN 827:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
3

---------------------- Page: 5 ----------------------
SIST EN 827:2006
EN 827:2005 (E)
SAFETY STATEMENT: Persons using this European Standard should be familiar with the normal
laboratory practice, in principle. This European Standard does not purport to address all of the safety
problems, if any, associated with its use. It is the responsibility of the user to establish appropriate
safety and health practices and to ensure compliance with any regulatory conditions.
1 Scope
This European Standard specifies a method for the determination of conventional solids content and, where
possible, constant mass solids content.
It is applicable to dispersion, emulsion and solvent based adhesives.
2 Normative references
The following referenced documents are indispensable for the application of this European Standard. For
dated references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 923, Adhesives — Terms and definitions
EN 1067, Adhesives — Examination and preparation of samples for testing
EN ISO 15605, Adhesives — Sampling (ISO 15605:2000)
3 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN 923 and the following apply.
3.1
conventional solids content
solids content obtained by heating a conventional amount of the sample placed in a given vessel at a given
temperature for a specific time
3.2
constant mass solids content
solids content obtained by heating the sample for successive intervals until the volatile components have
evaporated and the residue reaches a constant mass
4 Safety
...

SLOVENSKI STANDARD
SIST EN 827:2006
01-april-2006
1DGRPHãþD
SIST EN 827:1998
/HSLOD±'RORþHYDQMHVXKHJDRVWDQNDLQVXKHJDRVWDQNDSRVXãHQMXGRNRQVWDQWQH
PDVH
Adhesives - Determination of conventional solids content and constant mass solids
content
Klebstoffe - Bestimmung des Feststsoffgehaltes nach Vereinbarung und bis zur
Massekonstanz
Adhésifs - Détermination de l'extrait sec conventionnel et de l'extrait sec a masse
constante
Ta slovenski standard je istoveten z: EN 827:2005
ICS:
83.180 Lepila Adhesives
SIST EN 827:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 827:2006

---------------------- Page: 2 ----------------------

SIST EN 827:2006
EUROPEAN STANDARD
EN 827
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2005
ICS 83.180 Supersedes EN 827:1994
English Version
Adhesives - Determination of conventional solids content and
constant mass solids content
Adhésifs - Détermination de l'extrait sec conventionnel et Klebstoffe - Bestimmung des Feststsoffgehaltes nach
de l'extrait sec à masse constante Vereinbarung und bis zur Massekonstanz
This European Standard was approved by CEN on 21 November 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 827:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 827:2006
EN 827:2005 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions.4
4 Safety .4
5 Apparatus .5
6 Sampling.5
7 Procedure .5
8 Expression of results.7
9 Test report .8

2

---------------------- Page: 4 ----------------------

SIST EN 827:2006
EN 827:2005 (E)
Foreword
This European Standard (EN 827:2005) has been prepared by Technical Committee CEN/TC 193
“Adhesives”, the secretariat of which is held by AENOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2006, and conflicting national standards shall be withdrawn at
the latest by June 2006.
This European Standard supersedes EN 827:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN 827:2006
EN 827:2005 (E)
SAFETY STATEMENT: Persons using this European Standard should be familiar with the normal
laboratory practice, in principle. This European Standard does not purport to address all of the safety
problems, if any, associated with its use. It is the responsibility of the user to establish appropriate
safety and health practices and to ensure compliance with any regulatory conditions.
1 Scope
This European Standard specifies a method for the determination of conventional solids content and, where
possible, constant mass solids content.
It is applicable to dispersion, emulsion and solvent based adhesives.
2 Normative references
The following referenced documents are indispensable for the application of this European Standard. For
dated references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 923, Adhesives — Terms and definitions
EN 1067, Adhesives — Examination and preparation of samples for testing
EN ISO 15605, Adhesives — Sampling (ISO 15605:2000)
3 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN 923 and the following apply.
3.1
conventional solids content
solids content obtained by heating a conventional amount of the sample placed in a given vessel at a given
temperature for a specific time
3.2
constant mass solids content
solids content obtained by heating the sample for successive intervals until the volatile components have
evaporated and the residue reaches a constant mass
4 Safety
...