SIST EN ISO 14556:2001/A1:2007
(Amendment)Steel - Charpy V-notch pendulum impact test - Instrumented test method - Amendment 1: Annex D - Instrumented Charpy V-notch pendulum impact test of sub-size test pieces (ISO 14556:2000/Amd 1:2006)
Steel - Charpy V-notch pendulum impact test - Instrumented test method - Amendment 1: Annex D - Instrumented Charpy V-notch pendulum impact test of sub-size test pieces (ISO 14556:2000/Amd 1:2006)
Stahl - Kerbschlagbiegeversuch nach Charpy (V-Kerb) - Instrumentiertes Prüfverfahren - ÄNDERUNG 1: Anhang D - Prüfung von Kleinproben im instrumentierten Kerbschlagbiegeversuch nach Charpy (ISO 14556:2000/Amd 1:2006)
In diesem Anhang sind der instrumentierte Kerbschlagbiegeversuch nach Charpy (V-Kerb) für Kleinproben aus Stahlerzeugnissen sowie die Anforderungen an die Messeinrichtungen und die Auswerteverfahren festgelegt.
Die Anwendung dieser Internationalen Norm für andere metallische Werkstoffe und andere Schlagversuchseinrichtungen, wie Fallwerke oder servohydraulische Hochgeschwindigkeitsprüfmaschinen, kann vereinbart werden.
Mit diesem Versuch können weitergehende Aussagen über das Bruchverhalten des zu prüfenden Erzeugnisses getroffen werden.
Der Anwender wird darauf hingewiesen, dass die Ergebnisse von Kleinproben nicht direkt vergleichbar zu den Ergebnissen von genormten Charpy-V-Proben sein können und geeignete Korrelationen angewendet werden müssen.
Aciers - Essai de flexion par choc sur éprouvette Charpy a entaille en V - Méthode d'essai instrumenté - Amendement 1: Annexe D - Essai de flexion par choc instrumenté sur éprouvettes Charpy a entaille en V de dimensions réduites (ISO 14556:2000/Amd 1:2006)
Jeklo – Udarni preskus žilavosti po Charpyju (V-zareza) – Instrumentirana preskusna metoda – Dopolnilo 1: Dodatek D – Instrumentiran udarni preskus žilavosti po Charpyju (V-zareza) za majhne preskušance (ISO 14556:2000/Amd 1:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14556:2001/A1:2007
01-januar-2007
Jeklo – Udarni preskus žilavosti po Charpyju (V-zareza) – Instrumentirana
preskusna metoda – Dopolnilo 1: Dodatek D – Instrumentiran udarni preskus
žilavosti po Charpyju (V-zareza) za majhne preskušance (ISO 14556:2000/Amd
1:2006)
Steel - Charpy V-notch pendulum impact test - Instrumented test method - Amendment
1: Annex D - Instrumented Charpy V-notch pendulum impact test of sub-size test pieces
(ISO 14556:2000/Amd 1:2006)
Stahl - Kerbschlagbiegeversuch nach Charpy (V-Kerb) - Instrumentiertes Prüfverfahren -
ÄNDERUNG 1: Anhang D - Prüfung von Kleinproben im instrumentierten
Kerbschlagbiegeversuch nach Charpy (ISO 14556:2000/Amd 1:2006)
Aciers - Essai de flexion par choc sur éprouvette Charpy a entaille en V - Méthode
d'essai instrumenté - Amendement 1: Annexe D - Essai de flexion par choc instrumenté
sur éprouvettes Charpy a entaille en V de dimensions réduites (ISO 14556:2000/Amd
1:2006)
Ta slovenski standard je istoveten z: EN ISO 14556:2000/A1:2006
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
77.080.20 Jekla Steels
SIST EN ISO 14556:2001/A1:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 14556:2000/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2006
ICS 77.040.10
English Version
Steel - Charpy V-notch pendulum impact test - Instrumented test
method - Amendment 1: Annex D - Instrumented Charpy V-
notch pendulum impact test of sub-size test pieces (ISO
14556:2000/Amd 1:2006)
Aciers - Essai de flexion par choc sur éprouvette Charpy à Stahl - Kerbschlagbiegeversuch nach Charpy (V-Kerb) -
entaille en V - Méthode d'essai instrumenté - Amendement Instrumentiertes Prüfverfahren - ÄNDERUNG 1: Anhang D
1: Annexe D - Essai de flexion par choc instrumenté sur - Prüfung von Kleinproben im instrumentierten
éprouvettes Charpy à entaille en V de dimensions réduites Kerbschlagbiegeversuch nach Charpy (ISO
(ISO 14556:2000/Amd 1:2006) 14556:2000/Amd 1:2006)
This amendment A1 modifies the European Standard EN ISO 14556:2000; it was approved by CEN on 30 June 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14556:2000/A1:2006: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 14556:2000/A1:2006 (E)
Foreword
This document (EN ISO 14556:2000/A1:2006) has been prepared by Technical Committee
ISO/TC 164 "Mechanical testing of metals" in collaboration with Technical Committee ECISS/TC
1 "Steel - Mechanical testing", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2007, and conflicting national
standards shall be withdrawn at the latest by January 2007.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 14556:2000/Amd 1:2006 has been approved by CEN as EN ISO
14556:2000/A1:2006 without any modifications.
2
---------------------- Page: 3 ----------------------
INTERNATIONAL ISO
STANDARD 14556
First edition
2000-05-01
AMENDMENT 1
2006-07-01
Steel — Charpy V-notch pendulum impact
test — Instrumented test method
AMENDMENT 1: Annex D — Instrumented
Charpy V-notch pendulum impact test of
sub-size test pieces
Aciers — Essai de flexion par choc sur éprouvette Charpy à entaille
en V — Méthode d'essai instrumenté
AMENDEMENT 1: Annexe D — Essai de flexion par choc instrumenté
sur éprouvettes Charpy à entaille en V de dimensions réduites
Reference number
ISO 14556:2000/Amd.1:2006(E)
©
ISO 2006
---------------------- Page: 4 ----------------------
ISO 14556:2000/Amd.1:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 5 ----------------------
ISO 14556:2000/Amd.1:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 14556:2000 was prepared by Technical Committee ISO/TC 164, Mechanical testing of
metals, Subcommittee SC 4, Toughness testing — Fracture (F), Pendulum (P), Tear (T).
© ISO 2006 – All rights reserved iii
---------------------- Page: 6 ----------------------
ISO 14556:2000/Amd.1:2006(E)
Steel — Charpy V-notch pendulum impact test — Instrumented
test method
AMENDMENT 1: Annex D — Instrumented Charpy V-notch
pendulum impact test of sub-size test pieces
Page iii, Contents
Add
“Annex D (informative) Instrumented Charpy V-notch pendulum impact test of sub-size test pieces
.............................................14”
after Annex C.
Change the page number of the Bibliography to 21.
Page iv, Foreword
Replace the last sentence with the following:
"Annexes A to D of this International Standard are for information only."
Page 14
Insert the following annex before the Bibliography.
© ISO 2006 – All rights reserved 1
---------------------- Page: 7 ----------------------
ISO 14556:2000/Amd.1:2006(E)
Annex D
(informative)
Instrumented Charpy V-notch pendulum impact test
of sub-size test pieces
D.1 Introduction
This annex defines the instrumented Charpy V-notch pendulum impact testing of sub-size test pieces on steel
products and the requirements concerning the measurement and recording equipment.
This International Standard can be applied, by agreement, to other metallic materials and to other impact testing
machines, such as drop-weight towers or high-speed servo-hydraulic machines.
This test provides further information on the fracture behaviour of the tested product.
The user should be aware that data obtained from sub-size test pieces may not be directly comparable to
those obtained from full-size standard Charpy V-notch test pieces and that suitable correlation procedures
have to be employed.
D.2 Apparatus
D.2.1 Testing machine
The testing machine is similar to that used for conventional Charpy V-notch test pieces, with the exception of
the following characteristics, which have to be suitably modified taking into acc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.