oSIST prEN 16287:2011
(Main)Glass packaging - Screw finishes for pressure capsules - MCA 1 finish
Glass packaging - Screw finishes for pressure capsules - MCA 1 finish
This document specifies the dimensions of the 28 millimetres screw finish for glass containers designated MCA 1.
Verpackungen aus Glas - Schraubmundstücke für Flaschen mit Innendruck - MCA 1-Mundstück
Dieses Dokument legt die Maße des 28-mm-Schraubmundstückes für Behältnisse aus Glas, bezeichnet mit MCA 1, fest.
Emballage en verre - Bagues à vis pour capsules à pression - Bague MCA 1
Le présent document spécifie les dimensions de la bague à vis de 28 millimètres pour récipients en verre, désignée sous l'appellation bague MCA 1.
Steklena embalaža - Grla z navojem za steklenice pod tlakom - Grla MCA 1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 16287:2011
01-julij-2011
Steklena embalaža - Grla z navojem za steklenice pod tlakom - Grla MCA 1
Glass packaging - Screw finishes for pressure capsules - MCA 1 finish
Verpackungen aus Glas - Schraubmundstücke für Flaschen mit Innendruck - MCA 1-
Mundstück
Emballage en verre - Bagues à vis pour capsules à pression - Bague MCA 1
Ta slovenski standard je istoveten z: prEN 16287
ICS:
55.100 Steklenice. Lonci. Kozarci Bottles. Pots. Jars
oSIST prEN 16287:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 16287:2011
---------------------- Page: 2 ----------------------
oSIST prEN 16287:2011
EUROPEAN STANDARD
DRAFT
prEN 16287
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2011
ICS 55.100
English Version
Glass packaging - Screw finishes for pressure capsules - MCA 1
finish
Emballage en verre - Bagues à vis pour capsules à Verpackungen aus Glas - Schraubmundstücke für
pression - Bague MCA 1 Flaschen mit Innendruck - MCA 1-Mundstück
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 261.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16287:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 16287:2011
prEN 16287:2011 (E)
Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Definitions .5
3 Dimensions .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.