SIST EN 13329:2016+A2:2021
(Main)Laminate floor coverings - Elements with a surface layer based on aminoplastic thermosetting resins - Specifications, requirements and test methods
Laminate floor coverings - Elements with a surface layer based on aminoplastic thermosetting resins - Specifications, requirements and test methods
This European Standard specifies characteristics, requirements and test methods for laminate floor coverings with a surface layer based on aminoplastic thermosetting resins as defined in 3.1 and 3.2. It also specifies requirements for marking and packaging.
It includes a classification system, based on EN ISO 10874, giving practical requirements for areas of use and levels of use, to indicate where laminate floor coverings will give satisfactory service and to encourage the consumer to make an informed choice.
Laminate floor coverings are considered for domestic and commercial levels of use, including domestic kitchens. This standard does not specify requirements relating to areas which are subjected to frequent wetting, such as bathrooms, laundry rooms or saunas.
Laminatböden - Elemente mit einer Deckschicht auf Basis aminoplastischer, wärmehärtbarer Harze - Spezifikationen, Anforderungen und Prüfverfahren
Diese Europäische Norm legt Eigenschaften, Anforderungen und Prüfverfahren für Laminatböden mit einer Deckschicht auf Basis aminoplastischer, wärmehärtbarer Harze fest, wie in 3.1 und 3.2 definiert. Sie legt ebenfalls Anforderungen an die Kennzeichnung und Verpackung fest.
Sie enthält ein Klassifizierungssystem, das auf EN ISO 10874 basiert, mit praktischen Anforderungen für bestimmte Verwendungsbereiche und Beanspruchungsklassen. Dies dient dazu aufzuzeigen, in welchen Bereichen Laminatböden zufriedenstellend eingesetzt werden können, sowie dazu, den Verbraucher in die Lage zu versetzen, informiert eine Auswahl zu treffen.
Laminatböden sind im Allgemeinen zur schwimmenden Verlegung in den Anwendungsgebieten "Wohnen" und "Gewerblich" bestimmt, einschließlich einer Verwendung in Küchen im Wohnbereich. Dieses Dokument legt keine Anforderungen für die Verwendung in Bereichen fest, die regelmäßig Nässe ausgesetzt sind wie etwa Badezimmer, Hauswirtschaftsräume oder Saunen. Im Allgemeinen können Laminatböden in diesen Bereichen nur verwendet werden, wenn dies durch den Hersteller zugesichert wird und unter den in den Installationsrichtlinien des Herstellers beschriebenen Bedingungen.
Revêtements de sol stratifiés - Éléments dont la surface est à base de résines aminoplastes thermodurcissables - Spécifications, exigences et méthodes d'essai
La présente Norme européenne spécifie les caractéristiques, les exigences et les méthodes d’essai pour les revêtements de sol stratifiés dont le parement est à base de résines aminoplastes thermodurcissables, tels que définis en 3.1 et 3.2. Elle spécifie également les exigences relatives au marquage et à l’emballage.
Elle comporte un système de classification fondé sur l’EN ISO 10874, qui donne les exigences pratiques relatives aux zones et niveaux d’utilisation, afin d’indiquer les cas où les revêtements de sol stratifiés peuvent être utilisés de manière satisfaisante et favoriser ainsi un choix avisé du consommateur.
Les revêtements de sol stratifiés sont généralement conçus pour une pose flottante et sont destinés à des usages domestiques et commerciaux, notamment dans les cuisines domestiques. Le présent document ne spécifie pas d'exigences relatives aux lieux soumis à une humidification fréquente, comme les salles de bain, les buanderies ou les saunas. En général, les revêtements de sol stratifiés ne peuvent être utilisés dans ces zones que lorsque le fabricant l’autorise et dans des conditions décrites dans les lignes directrices d’installation du fabricant.
Laminatne talne obloge - Elementi z zunanjo plastjo na osnovi aminoplastičnih termostabilnih smol - Specifikacije, zahteve in preskusne metode
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13329:2016+A2:2021
01-november-2021
Laminatne talne obloge - Elementi z zunanjo plastjo na osnovi aminoplastičnih
termostabilnih smol - Specifikacije, zahteve in preskusne metode
Laminate floor coverings - Elements with a surface layer based on aminoplastic
thermosetting resins - Specifications, requirements and test methods
Laminatböden - Elemente mit einer Deckschicht auf Basis aminoplastischer,
wärmehärtbarer Harze - Spezifikationen, Anforderungen und Prüfverfahren
Revêtements de sol stratifiés - Éléments dont la surface est à base de résines
aminoplastes thermodurcissables - Spécifications, exigences et méthodes d'essai
Ta slovenski standard je istoveten z: EN 13329:2016+A2:2021
ICS:
97.150 Talne obloge Floor coverings
SIST EN 13329:2016+A2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13329:2016+A2:2021
---------------------- Page: 2 ----------------------
SIST EN 13329:2016+A2:2021
EN 13329:2016+A2
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2021
EUROPÄISCHE NORM
ICS 97.150 Supersedes EN 13329:2016+A1:2017
English Version
Laminate floor coverings - Elements with a surface layer
based on aminoplastic thermosetting resins -
Specifications, requirements and test methods
Revêtements de sol stratifiés - Éléments dont la surface Laminatböden - Elemente mit einer Deckschicht auf
est à base de résines aminoplastes thermodurcissables Basis aminoplastischer, wärmehärtbarer Harze -
- Spécifications, exigences et méthodes d'essai Spezifikationen, Anforderungen und Prüfverfahren
This European Standard was approved by CEN on 27 November 2015 and includes Amendment 1 approved by CEN on 1 July
2017 and includes Amendment 2 approved by CEN on 18 July 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATIO N
EUROPÄISCHES KOMITEE FÜR NORMUN G
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13329:2016+A2:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13329:2016+A2:2021
EN 13329:2016+A2:2021 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Requirements . 7
4.1 General requirements . 7
4.2 Classification requirements . 8
4.3 Additional technical characteristics . 10
5 Marking and packaging . 10
5.1 Marking . 10
5.2 Packaging . 12
6 Test report . 12
Annex A (normative) Determination of thickness, length, width, squareness, straightness
and flatness . 13
A.1 Sampling . 13
A.2 Conditioning . 13
A.3 Apparatus . 13
A.4 Procedure. 15
A.4.1 Determination of thickness (t) . 15
A.4.2 Determination of length (l). 16
A.4.3 Determination of width (w) . 17
A.4.4 Determination of dimensions of squared elements . 17
A.4.5 Determination of squareness (q) . 18
A.4.6 Determination of straightness (s) . 18
A.4.7 Determination of width flatness (f ) . 19
w
A.4.8 Determination of length flatness (f ) . 19
l
A.5 Calculation and expression of results . 20
A.5.1 Thickness (t) . 20
A.5.2 Length (l) . 20
A.5.3 Width (w) . 20
A.5.4 Squareness (q) . 20
A.5.5 Straightness (s) . 21
A.5.6 Width flatness (f ) . 21
w
A.5.7 Length flatness (f ) . 21
l
Annex B (normative) Determination of openings and height difference between elements . 22
B.1 Sampling . 22
B.2 Conditioning . 22
B.3 Apparatus . 22
B.4 Procedure. 22
B.4.1 Assembling . 22
B.4.2 Determination of opening between elements (o) . 23
B.4.3 Determination of height difference (h) . 23
B.5 Calculation and expression of results . 23
2
---------------------- Page: 4 ----------------------
SIST EN 13329:2016+A2:2021
EN 13329:2016+A2:2021 (E)
Annex C (normative) Determination of dimensional variations after changes in relative
humidity . 24
C.1 General . 24
C.2 Sampling . 24
C.3 Conditioning . 24
C.4 Calculation and expression of results . 25
Annex D (normative) Determination of surface soundness . 26
D.1 General . 26
D.2 Sampling . 26
D.3 Conditioning . 26
D.4 Procedure . 26
D.4.1 Preparing the test specimen . 26
D.4.2 Bonding the steel pad to the surface. 27
D.4.3 Determination of force at fracture . 27
D.5 Calculation and expression of results . 27
Annex E (normative) Determination of abrasion resistance and abrasion classification . 28
E.1 Sampling . 28
E.2 Conditioning . 28
E.3 Apparatus . 29
E.3.1 Testing machine . 29
E.3.2 Additional material or equipment . 31
E.4 Procedure . 32
E.4.1 General . 32
E.4.2 Preparation of test specimens and abrasive papers . 32
E.4.3 Preparation of abrasive wheels . 32
E.4.4 Determination of the abrasion rate of abrasive paper . 32
E.4.5 Abrasion of test specimen . 32
E.4.6 Expression of results . 33
E.4.7 Test report . 34
Annex F (normative) Calibration and Maintenance of Abrasion equipment . 35
F.1 General . 35
F.2 Apparatus . 35
F.3 Procedure . 35
F.3.1 Bearing Wear. 35
F.3.2 Shaft Wear . 35
F.3.3 Alignment . 36
Annex G (normative) Measurement of shore A hardness . 38
Annex H (normative) #Determination of large ball impact resistance . 39
H.1 General . 39
H.2 Apparatus . 39
H.2.1 Test devices . 39
H.2.2 Underlay . 39
H.2.3 Marking pen with water washable ink . 39
H.2.4 Cloth . 39
H.3 Procedure . 39
H.3.1 Large-diameter ball test$ . 39
Bibliography . 41
3
---------------------- Page: 5 ----------------------
SIST EN 13329:2016+A2:2021
EN 13329:2016+A2:2021 (E)
European foreword
This document (EN 13329:2016+A2:2021) has been prepared by Technical Committee CEN/TC 134
“Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2022, and conflicting national standards shall
be withdrawn at the latest by March 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1 approved by CEN on 2017-07-01 and Amendment 2 approved
by CEN on 2021-07-18.
This document supersedes #EN 13329:2016+A1:2017$.
The start and finish of text introduced or altered by amendment is indicated in the text by tags !"
and #$.
#In comparison with the previous version EN 13329:2016+A1:2017 of the original edition EN
13329:2016, the new consolidated version EN 13329:2016+A2:2021 contains the following technical
modifications:
— Normative references: replace EN 424, Resilient floor coverings - Determination of the effect of
simulated movement of a furniture leg with EN ISO 16581, Resilient and laminate floor coverings —
Determination of the effect of simulated movement of a furniture leg;
— Normative references: add EN 17368, Laminate floor coverings - Determination of impact resistance
with small ball”;
— Scope: replacement of the last paragraph;
— term 3.3 substrate: replacement of the definition;
— Table 2: change the requirements and test method for impact resistance: small ball and addition of
d
footnote to table as clarification for testing, replacement of Table 2;
— Annex H: small ball test method has been deleted, replacement of Annex H.$
!deleted text"
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
4
---------------------- Page: 6 ----------------------
SIST EN 13329:2016+A2:2021
EN 13329:2016+A2:2021 (E)
1 Scope
This European Standard specifies characteristics, requirements and test methods for laminate floor
coverings with a surface layer based on aminoplastic thermosetting resins as defined in 3.1 and 3.2. It
also specifies requirements for marking and packaging.
It includes a classification system, based on EN ISO 10874, giving practical requirements for areas of
use and levels of use, to indicate where laminate floor coverings will give satisfactory service and to
encourage the consumer to make an informed choice.
#Laminate floor coverings are generally designed for floating installations and are considered for
domestic and commercial levels of use, including domestic kitchens. This document does not specify
requirements relating to the use in areas which are subjected to frequent wetting, such as bathrooms,
laundry rooms or saunas. In general laminate floor coverings can only be used in those areas when
authorized by the manufacturer and under conditions described in the manufacturer's installation
guidelines.$
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 311, Wood-based panels — Surface soundness — Test method
EN 318, Wood based panels — Determination of dimensional changes associated with changes in relative
humidity
EN 322, Wood-based panels — Determination of moisture content
#EN ISO 16581, Resilient and laminate floor coverings — Determination of the effect of simulated
movement of a furniture leg (ISO 16581)$
EN 425:2002, Resilient and laminate floor coverings — Castor chair test
EN 438 (all parts), High-pressure decorative laminates (HPL) — Sheets based on thermosetting resins
(Usually called Laminates)
EN 16094, Laminate floor coverings — Test method for the determination of micro-scratch resistance
#EN 17368, Laminate floor coverings — Determination of impact resistance with small ball$
CEN/TS 16354, Laminate floor coverings — Underlays — Specification, requirements and test methods
EN 20105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour
(ISO 105-A02)
EN ISO 105-B02, Textiles — Tests for colour fastness — Part B02: Colour fastness to artificial light: Xenon
arc fading lamp test (ISO 105-B02)
EN ISO 4892-2:2006/A1:2009, Plastics — Methods of exposure to laboratory light sources — Part 2:
Xenon-arc lamps (ISO 4892-2:2006/Amd1:2009)
EN ISO 6506-1, Metallic materials — Brinell hardness test — Part 1: Test method (ISO 6506-1)
5
---------------------- Page: 7 ----------------------
SIST EN 13329:2016+A2:2021
EN 13329:2016+A2:2021 (E)
EN ISO 10874, Resilient, textile and laminate floor coverings — Classification (ISO 10874)
EN ISO 24343-1, Resilient and laminate floor coverings — Determination of indentation and residual
indentation — Part 1: Residual indentation (ISO 24343-1)
ISO 48, Rubber, vulcanized or thermoplastic — Determination of hardness (hardness between 10 IRHD
and 100 IRHD)
ISO 7267-2, Rubber-covered rollers — Determination of apparent hardness — Part 2: Shore-type
durometer method
ISO 24334, Laminate floor coverings — Determination of locking strength for mechanically assembled
panels
ISO 24336, Laminate floor coverings — Determination of thickness swelling after partial immersion in
water
ISO 24339, Laminate and textile floor coverings — Determination of dimensional variations after
exposure to humid and dry climate conditions
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
laminate floor covering
rigid floor covering, typically in a plank or tile format, with a multiple layer structure: e.g. backer,
substrate, décor and worked edges that allow the product to be joined together to form a larger integral
unit
Note 1 to entry: Laminate flooring does not include products having a resilient, stone, textile, wood, leather or
metal top surfacing material(s).
3.2
surface layer based on aminoplastic thermosetting resins
upper decorative layer, which may vary in surface texture and gloss level, consisting of one or more thin
sheets of a fibrous material (usually paper), impregnated with aminoplastic, thermosetting resins
(usually melamine)
Note 1 to entry: By the simultaneous action of heat and pressure, these sheets are either pressed as such (HPL,
CPL, Compact), and in the case of HPL and CPL bonded on a substrate (usually wood-based panels), or in the case
of DPL directly pressed on a substrate (usually wood-based panels). The product is usually finished with a backer
(e.g. HPL, CPL, impregnated papers), primarily used as a balancing material.
3.3
substrate
#core material of the laminate floor covering containing wood for at least 65 % in mass$
Note 1 to entry: It is generally a particleboard, as defined in EN 309, or a dry process fibreboard (MDF) as
3
defined in EN 316 or a so called High Density Fibreboard (HDF) which is a MDF-board with a density ≥ 800 kg/m .
3.4
backer
layer opposite to the surface layer used to balance and stabilize the product
6
---------------------- Page: 8 ----------------------
SIST EN 13329:2016+A2:2021
EN 13329:2016+A2:2021 (E)
Note 1 to entry: The backer is generally made of impregnated papers.
3.5
underlay
layer placed between the laminate floor covering and the subfloor to impart specific properties
Note 1 to entry: Some laminate floor covering products have the underlay pre-attached directly to the backer.
3.6
laminate floor covering element
piece of the floor covering with profiled edges to facilitate assembly at installation
Note 1 to entry: See Figure 1.
Key
1 surface layer
2 substrate
3 backer
4 underlay (optional)
Figure 1— Laminate floor-covering element
4 Requirements
4.1 General requirements
All laminate floor coverings shall conform to the general requirements given in Table 1, when tested by
the methods specified therein.
7
---------------------- Page: 9 ----------------------
SIST EN 13329:2016+A2:2021
EN 13329:2016+A2:2021 (E)
Table 1 — General requirements
Characteristic Requirement Test method
Thickness of the element, (t) Δtaverage ≤ 0,50 mm, relative to nominal value Annex A
without underlay t - t ≤ 0,50 mm
max. min.
With pre-attached underlay Δt ≤ 0,50 mm, relative to nominal value Annex A
average
tmax.- tmin. ≤ 0,80 mm
Length of the surface layer, (l) For the nominal values given, no measured value Annex A
shall exceed:
l ≤ 1 500 mm: Δl ≤ 0,5 mm
l > 1 500 mm: Δl ≤ 0,3 mm/m
Width of the surface layer, (w) Δw ≤ 0,10 mm, relative to nominal value Annex A
average
w – w ≤ 0,20 mm
max. min.
Length and width of squared elements, Δl ≤ 0,10 mm relative to nominal value Annex A
average
(l = w)
Δwaverage ≤ 0,10 mm, relative to nominal value
lmax. – lmin. ≤ 0,20 mm
w – w ≤ 0,20 mm
max. min.
Squareness of the element, (q) q ≤ 0,20 mm Annex A
max.
Straightness of the surface layer, (s) s ≤ 0,30 mm/m Annex A
max.
Flatness of the element, (f) Maximum single values: Annex A
f ≤ 0,15 % f ≤ 0,20 %
w, concave w, convex
f l, concave ≤ 0,50 % f l, convex ≤ 1,00 %
Openings between elements, (o) o average ≤ 0,15 mm Annex B
o max. ≤ 0,20 mm
Height difference between elements, (h) h average ≤ 0,10 mm Annex B
h ≤ 0,15 mm
max.
Dimensional variations after changes in δl ≤ 0,9 mm Annex C
average
relative humidity, (δl, δw)
δw average ≤ 0,9 mm
Light fastness Colour contrast between unexposed and exposed EN ISO 4892-2:20
sample part ≥ 4 of grey scale according to 06/A1:2009
EN 20105—A02 procedure B –
cycle 5 (50 % rel.
a b
hum.)
Static indentation residual indentation ≤ 0,05 mm EN ISO 24343-1
a
Test until blue wool scale No. 6 according to EN ISO 105-B02 (= colour contrast 4 on the grey scale according to
EN 20105-A02 between exposed and unexposed part of blue wool scale).
b
Allow sample (24 ± 1 h) recovery time without light exposure at 23 °C and 50 % rel. humidity before taking final
assessment.
4.2 Classification requirements
All laminate floor coverings shall be classified as suitable for different levels of use according to the
requirements specified in Table 2, when tested by the methods given therein. Classification shall
conform to the scheme specified in EN ISO 10874.
The large ball impact test and the castor chair test of class 34 products shall be carried out with the pre-
attached underlays or with an underlay specified by the manufacturer. For the large ball impact test of
8
---------------------- Page: 10 ----------------------
SIST EN 13329:2016+A2:2021
EN 13329:2016+A2:2021 (E)
products of the classes 21 – 23 and 31 – 33 a standard EPS foam of (1,8 ± 0,2) mm thickness, with a CS
1
value of (60 ± 10) kPa and with PC-value of (0,9 ± 0,1) mm shall be used . The three parameters of the
foam shall be determined according to CEN/TS 16354.
#Table 2 — Classification requirements and level of use
Level of use
Domestic Commercial
Moderate General Heavy Moderate General Heavy Very
Heavy
Class: 21 22 23 31 32 33 34 Test
method
Abrasion AC1 AC2 AC3 AC4 AC5 AC6 Ann
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.