SIST HD 363 S1:2003
(Main)Dimensions of spindle ends for manually operated electronic components
Dimensions of spindle ends for manually operated electronic components
Contains dimensions and tolerances for spindle ends made to original inch dimensions.
Abmessungen der Achsenden für handbetätigte elektromechanische Bauelemente
Dimensions des terminaisons des axes de composants électroniques pour commande manuelle
Contient des dimensions et des tolérances pour terminaisons des axes réalisés selon les dimensions originales en inches.
Dimensions of spindle ends for manually operated electronic components
General Information
Standards Content (Sample)
SLOVENSKI SIST HD 363 S1:2003
STANDARD
marec 2003
Dimensions of spindle ends for manually operated electronic components
ICS 31.240 Referenčna številka
© Standard
...
This May Also Interest You
This part of IEC 61969 specifies a set of basic environmental requirements and tests, as well
as safety aspects for outdoor enclosures for electrical and electronic equipment, under
conditions of non-weatherprotected locations above ground.
The purpose of this document is to define a minimum level of environmental performance in
order to meet requirements of storage, transport and final installation. The intention is to
establish basic environmental performance criteria for outdoor enclosure compliance.
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 61969 contains design guidelines for outdoor enclosures for electrical and electronic equipment and is applicable over a wide field of mechanical, electromechanical and electronic equipment and its installation where a modular design is used.
The objectives of this document are:
- to provide an overview of specifications for enclosures focused on requirements for outdoor applications for stationary use at non-weather protected locations, and
- to achieve product integrity under outdoor conditions and to ease product selection for the sourcing of outdoor enclosures from different vendors.
These enclosures are considered to contain any equipment and provide protection for the outdoor installed facilities against unwanted environmental impacts. The installed equipment can be, but is not limited to, subracks or chassis according to IEC 60917 (all parts) or IEC 60297 (all parts). A typical outdoor enclosure is shown in Figure 1.
[Figure 1]
- Standard18 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 60286-2:2022 applies to the tape packaging of components with two or more unidirectional leads for use in electronic equipment. It provides dimensions and tolerances necessary to tape components with unidirectional leads. In general, the tape is applied to the component leads.
It covers requirements for taping techniques used with equipment for automatic handling, pre-forming of leads, insertion and other operations and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes.
This edition includes the following significant technical changes with respect to the previous edition:
a) complete revision of structure;
b) consolidation of essential parameters and requirements in Clause 4.
- Standard37 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 61760 defines requirements for component specifications of electronic
components that are intended for usage in surface mounting technology. To this end, it
specifies a reference set of process conditions and related test conditions to be considered
when compiling component specifications.
The objective of this document is to ensure that a wide variety of SMDs can be subjected to
the same placement, mounting and subsequent processes (e.g. cleaning, inspection) during
assembly. This document defines tests and requirements that need to be part of any SMD
component's general, sectional or detail specification. In addition, this document provides
component users and manufacturers with a reference set of typical process conditions used in
surface mounting technology.
Some of the requirements for component specifications in this document are also applicable
to components with leads intended for mounting on a circuit board. Cases for which this is
appropriate are indicated in the relevant subclauses.
- Standard47 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 61587 specifies environmental requirements, test set-ups, as well as safety
aspects for empty enclosures, i.e. cabinets, racks, subracks, chassis, chassis integrated
subracks and associated plug-in units under indoor condition use and transportation. It defines
classifications (product performance levels) for these products, regarding and simulating the
usually arising loads during their use. For mechanical static and dynamic load tests typical
examples with dummy loads are used.
The purpose of this document is to establish defined levels of physical performance in order to
meet certain requirements of manufacture, storage, transport and final location conditions.
This document applies in general only to the above cited mechanical structures.
- Standard50 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 61587 specifies security aspects and security performance levels of the
mechanical construction of indoor cabinets in accordance with IEC 60917 (all parts) and
IEC 60297 (all parts). This document does not address vandalism.
NOTE Protection against vandalism is typically controlled by user-specific requirements.
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 62966, dedicated to aisle containment techniques for information technology
(IT) equipment typically used in data centres, describes the quantification of its air tightness, in
particular the air loss ratio that describes the content of the volumetric flow not used for cooling
the IT equipment. This ratio provides an index of efficiency, being inversely proportional to
efficiency (the lower this ratio, the higher the efficiency). This document provides methods to
measure an aisle containment air leakage rate and defines a classification system for aisle
containment leakage.
This document defines:
a) the measurement of the air leakage of the individual components of an aisle containment;
b) a method for calculating the air leakage of an aisle containment based on its individual
components;
c) a method for calculating the air leakage rate of an aisle containment in relation to the utilised
IT equipment;
d) a classification system for aisle containment leakage.
- Standard27 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 61969 specifies a set of basic environmental requirements and tests, as well
as safety aspects for outdoor enclosures under conditions of non-weather protected locations
above ground.
The purpose of this document is to define a minimum level of environmental performance in
order to meet requirements of storage, transport and final installation. The intention is to
establish basic environmental performance criteria for outdoor enclosure compliance.
- Standard16 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 61969 contains design guidelines for outdoor enclosures and is applicable over
a wide field of mechanical, electromechanical and electronic equipment and its installation
where a modular design is used.
The objectives of this document are:
– to provide an overview of specifications for enclosures focused on requirements for outdoor
applications for stationary use at non-weather protected locations, and
– to achieve product integrity under outdoor conditions and to ease product selection for the
sourcing of outdoor enclosures from different vendors.
These enclosures are considered to contain any equipment and provide protection for the
outdoor installed facilities against unwanted environmental impacts. The installed equipment
can be, but is not limited to, subracks or chassis according to IEC 60917 (all parts) or
IEC 60297 (all parts).
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 62610-6 which deals with thermal management for cabinets in accordance withIEC 60297 and IEC 60917 series, provides compatible measurement methods of recirculationratio and bypass ratio which are indicators for defining quality of airflow in the forced air coolingthat can be commonly applied to indoor cabinets for mounting subrack and/or chassis-basedequipment.
- Standard27 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.