SIST EN 60695-11-2:2017
(Main)Fire hazard testing - Part 11-2: Test flames - 1 kW pre-mixed flame - Apparatus, confirmatory test arrangement and guidance (IEC 60695-11-2:2017)
Fire hazard testing - Part 11-2: Test flames - 1 kW pre-mixed flame - Apparatus, confirmatory test arrangement and guidance (IEC 60695-11-2:2017)
This part of IEC 60695 gives the requirements for the production and confirmation of a
nominal 1 kW propane/air pre-mixed flame for use in fire hazard testing.
This basic safety publication is intended for use by technical committees in the preparation of
standards in accordance with the principles laid down in IEC Guide 104 [4] and
ISO/IEC Guide 51 [5].
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications in the preparation of its publications.
The requirements, test methods or test conditions of this basic safety publication will not
apply unless specifically referred to or included in the relevant publications.
Prüfungen zur Beurteilung der Brandgefahr - Teil 11-2 : Prüfflammen - Vorgemischte 1-kW-Flamme - Prüfeinrichtung, Aufbau zur Bestätigungsprüfung und Leitfaden
Essais relatifs aux risques du feu - Partie 11-2: Flammes d'essai - Flamme à prémélange de 1 kW nominal - Appareillage, configuration pour l'essai de vérification et préconisations
NEW!IEC 60695-11-2:2017 est disponible sous forme de IEC 60695-11-2:2017 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.
IEC 60695-11-2:2017 spécifie les exigences pour la production et la validation d’une flamme de type à prémélange à base de propane/air de 1 kW nominal pour utilisation dans les essais relatifs aux risques du feu. La présente publication fondamentale de sécurité est destinée à être utilisée par les comités d’études dans le cadre de l’élaboration de normes conformément aux principes établis dans le Guide IEC 104 et le Guide ISO/IEC 51. Elle a le statut d’une publication fondamentale de sécurité conformément au Guide IEC 104 et au Guide ISO/IEC 51.
Cette troisième édition de l’IEC 60695-11-2 annule et remplace la deuxième édition parue en 2013. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: ajout d'une variante pour la production de la flamme d'essai; suppression de l'Annexe B.
Dans cette norme, les caractères suivants sont utilisés: termes définis à l'Article 3: en gras.
Mots-clés: risque du feu, flamme de type à prémélange, flamme d’essai normalisée de 1 kW
Preskušanje požarne ogroženosti - 11-2. del: Preskusni plameni - Predmešani plamen z močjo 1 kW - Aparat, način potrditvenega preskušanja in navodilo (IEC 60695-11-2:2017)
Ta del standarda IEC 60695 podaja zahteve za izdelavo in potrditev propanskega/z zrakom predmešanega plamena z nazivno močjo 1 kW za preskušanje požarne ogroženosti.
Ta osnovna varnostna publikacija je namenjena tehničnim odborom za pripravo standardov v skladu z načeli vodil IEC 104 [4] in ISO/IEC 51 [5].
Ena od pristojnosti tehničnih odborov je, da med pripravo publikacij uporabljajo osnovne varnostne publikacije, kadar je to primerno.
Zahteve, preskusne metode ali preskusni pogoji iz te osnovne varnostne publikacije se ne uporabljajo, razen če so izrecno navedeni ali zajeti v ustreznih publikacijah.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60695-11-2:2017
01-december-2017
1DGRPHãþD
SIST EN 60695-11-2:2014
3UHVNXãDQMHSRåDUQHRJURåHQRVWLGHO 3UHVNXVQLSODPHQL3UHGPHãDQL
SODPHQ]PRþMRN:$SDUDWQDþLQSRWUGLWYHQHJDSUHVNXãDQMDLQQDYRGLOR ,(&
Fire hazard testing - Part 11-2: Test flames - 1 kW pre-mixed flame - Apparatus,
confirmatory test arrangement and guidance (IEC 60695-11-2:2017)
Ta slovenski standard je istoveten z: EN 60695-11-2:2017
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
SIST EN 60695-11-2:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60695-11-2:2017
---------------------- Page: 2 ----------------------
SIST EN 60695-11-2:2017
EUROPEAN STANDARD EN 60695-11-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2017
ICS 13.220.40 Supersedes EN 60695-11-2:2014
English Version
Fire hazard testing -
Part 11-2: Test flames - 1 kW nominal pre-mixed flame -
Apparatus, confirmatory test arrangement and guidance
(IEC 60695-11-2:2017)
Essais relatifs aux risques du feu - Prüfungen zur Beurteilung der Brandgefahr -
Partie 11-2: Flammes d'essai - Flamme à prémélange Teil 11-2 : Prüfflammen - Vorgemischte 1-kW-Flamme -
de 1 kW nominal - Appareillage, configuration pour l'essai Prüfeinrichtung, Aufbau zur Bestätigungsprüfung
de vérification et préconisations und Leitfaden
(IEC 60695-11-2:2017) (IEC 60695-11-2:2017)
This European Standard was approved by CENELEC on 2017-07-13. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60695-11-2:2017 E
---------------------- Page: 3 ----------------------
SIST EN 60695-11-2:2017
EN 60695-11-2:2017
European foreword
The text of document 89/1327/CDV, future edition 3 of IEC 60695-11-2, prepared by IEC/TC 89 "Fire
hazard testing" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 60695-11-2:2017.
The following dates are fixed:
• latest date by which the document has to be implemented at (dop) 2018-04-13
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with (dow) 2020-07-13
the document have to be withdrawn
This document supersedes EN 60695-11-2:2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60695-11-2:2017 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60695-1-10 NOTE Harmonized as EN 60695-1-10.
IEC 60695-1-11 NOTE Harmonized as EN 60695-1-11.
2
---------------------- Page: 4 ----------------------
SIST EN 60695-11-2:2017
EN 60695-11-2:2017
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60584-1 - Thermocouples - Part 1: EMF EN 60584-1 -
specifications and tolerances
ISO 13943 2008 Fire safety - Vocabulary - -
3
---------------------- Page: 5 ----------------------
SIST EN 60695-11-2:2017
---------------------- Page: 6 ----------------------
SIST EN 60695-11-2:2017
IEC 60695-11-2
®
Edition 3.0 2017-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
BASIC SAFETY PUBLICATION
PUBLICATION FONDAMENTALE DE SÉCURITÉ
Fire hazard testing –
Part 11-2: Test flames – 1 kW nominal pre-mixed flame – Apparatus,
confirmatory test arrangement and guidance
Essais relatifs aux risques du feu –
Partie 11-2: Flammes d’essai – Flamme à prémélange de 1 kW nominal –
Appareillage, configuration pour l’essai de vérification et préconisations
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.220.40 ISBN 978-2-8322-4313-8
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 60695-11-2:2017
– 2 – IEC 60695-11-2:2017 © IEC 2017
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Burner/supply arrangement. 7
4.1 Requirements . 7
4.2 Apparatus and fuel . 7
4.2.1 Burner . 7
4.2.2 Flow control . 7
4.2.3 Copper block . 8
4.2.4 Thermocouple . 8
4.2.5 Temperature/time indicating/recording devices . 8
4.2.6 Laboratory fumehood/chamber . 8
5 Production of the test flame . 8
5.1 Selection of the method . 8
5.2 Method A . 9
5.3 Method B (alternative) . 9
6 Confirmation of the test flame . 9
6.1 Principle . 9
6.2 Frequency of confirmatory tests . 9
6.3 Procedure . 10
7 Recommended arrangements for use of the test flame . 10
Annex A (normative) Burner details, arrangements and confirmatory test . 12
A.1 Burner construction . 12
A.2 Gas supply arrangement . 17
A.3 The copper block . 18
A.4 Confirmatory test . 18
Bibliography . 20
Figure 1 – Flame dimensions . 11
Figure A.1 – General assembly . 13
Figure A.2 – Burner details (1) . 13
Figure A.3 – Burner details (2) . 14
Figure A.4 – Burner details (3) . 15
Figure A.5 – Burner details (4) . 16
Figure A.6 – Example of supply arrangement for burner . 17
Figure A.7 – Copper block . 18
Figure A.8 – Confirmatory test arrangement . 19
---------------------- Page: 8 ----------------------
SIST EN 60695-11-2:2017
IEC 60695-11-2:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIRE HAZARD TESTING –
Part 11-2: Test flames – 1 kW nominal pre-mixed flame –
Apparatus, confirmatory test arrangement and guidance
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60695-11-2 has been prepared by IEC technical committee 89:
Fire hazard testing.
The text of this International Standard is based on the following documents:
CDV Report on voting
89/1327/CDV 89/1354/RVC
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 9 ----------------------
SIST EN 60695-11-2:2017
– 4 – IEC 60695-11-2:2017 © IEC 2017
This third edition of IEC 60695-11-2 cancels and replaces the second edition published in
2013. It constitutes a technical revision.
It has the status of a basic safety publication in accordance with IEC Guide 104 and
ISO/IEC Guide 51.
This edition includes the following significant technical changes with respect to the previous
edition:
• addition of an alternative production of the test flame;
• deletion of Annex B.
In this standard, the following print types are used:
• terms defined within Clause 3: in bold type
A list of all the parts in the IEC 60695 series, under the general title Fire hazard testing can
be found on the IEC web site.
Part 11 consists of the following parts:
Part 11-2: Test flames – 1 kW nominal pre-mixed flame – Apparatus, confirmatory test
arrangement and guidance
Part 11-3: Test flames – 500 W flames – Apparatus and confirmational test methods
Part 11-4: Test flames – 50 W flame – Apparatus and confirmational test method
Part 11-5: Test flames – Needle-flame test method – Apparatus, confirmatory test
arrangement and guidance
Part 11-10: Test flames – 50 W horizontal and vertical flame test methods
Part 11-11: Test flames – Determination of the characteristic heat flux for ignition from a
non-contacting flame source
Part 11-20: Test flames – 500 W flame test methods
Part 11-30: Test flames – History and development from 1979 to 1999
Part 11-40: Test flames – Confirmatory tests – Guidance
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this publication using a colour printer.
---------------------- Page: 10 ----------------------
SIST EN 60695-11-2:2017
IEC 60695-11-2:2017 © IEC 2017 – 5 –
INTRODUCTION
In the design of any electrotechnical product, the risk of fire and the potential hazards
associated with fire need to be considered. In this respect the objective of component, circuit,
and product design, as well as the choice of materials, is to reduce to acceptable levels the
potential risks of fire during normal operating conditions, reasonable foreseeable abnormal
1
use, malfunction, and/or failure. The IEC has developed IEC 60695-1-10 [1] , together with its
companion, IEC 60695-1-11 [2], to provide guidance on how this is to be accomplished.
The primary aims of IEC 60695-1-10 and IEC 60695-1-11 are to provide guidance on how:
a) to prevent ignition caused by an electrically energized component part, and
b) to confine any resulting fire within the bounds of the enclosure of the electrotechnical
product in the event of ignition.
Secondary aims of these documents include the minimization of any flame spread beyond the
product’s enclosure and the minimization of harmful effects of fire effluents such as heat,
smoke, toxicity and/or corrosivity.
Fires involving electrotechnical products can also be initiated from external non-electrical
sources. Considerations of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.