SIST EN 50085-2-4:2009
(Main)Cable trunking systems and cable ducting systems for electrical installations - Part 2-4: Particular requirements for service poles
Cable trunking systems and cable ducting systems for electrical installations - Part 2-4: Particular requirements for service poles
This European Standard specifies requirements and tests for cable trunking systems (CTS) and cable ducting systems (CDS) intended for the accommodation, and where necessary for the electrically protective separation, of insulated conductors, cables and possibly other electrical equipment in electrical and/or communication systems installations. The maximum voltage of these installations is 1 000 V a.c. and 1 500 V d.c. Service poles and service posts are intended to be mounted in free space and in contact with mounting surface(s) only at one or two ends, where the word "mounted" means fixed or placed on the floor with a weighted base or linked to a mounting surface through a flexible component. NOTE Service poles and service posts can also be part of a CTS/CDS intended for wall or ceiling mounting covered by Part 2-1 or floor mounting covered by Part 2-2 and are then also tested according to Part 2-1 and/or Part 2-2 as appropriate. This European Standard does not apply to conduit systems, cable tray systems, cable ladder systems, powertrack systems or equipment covered by other standards. This European Standard shall be used in conjunction with EN 50085-1:2005 "Cable trunking systems and cable ducting systems for electrical installations - Part 1: General requirements" which is referred to in this document as Part 1.
Elektroinstallationskanalsysteme für elektrische Installationen - Teil 2-4: Besondere Anforderungen für freistehende Installationseinheiten
Diese Europäische Norm legt Anforderungen und Prüfungen für Elektroinstallationskanalsysteme, die für die Aufnahme und, wo erforderlich, für die Auseinanderhaltung oder Separierung von isolierten Leitern, Kabeln, Leitungen und möglichen anderen elektrischen Betriebsmitteln in elektrischen Installationen oder Kommunikationssystemen fest. Die maximale Spannung dieser Installationen ist 1 000 V Wechselspannung und 1 500 V Gleichspannung. Freistehende Installationseinheiten sind für die freistehende Montage und die Montage in Kontakt mit Montageflächen an einem oder an zwei Enden vorgesehen. Der Begriff Montage bedeutet befestigt oder mit einer beschwerten Basis auf dem Boden stehend oder mit einem flexiblen Bauteil an einer Montagefläche befestigt. ANMERKUNG Freistehende Installationseinheiten können Teil eines Elektroinstallationskanalsystems für Wand und Decke nach Teil 2-1 oder eines Elektroinstallationskanalsystems für Installationen unterflur, aufflur oder boden¬bündig nach Teil 2-2 sein. Diese Europäische Norm gilt nicht für Elektroinstallationsrohrsysteme, Kabelträgersysteme, Stromschienensysteme oder Einrichtungen, die von anderen Normen abgedeckt sind. Diese Europäische Norm muss zusammen mit EN 50085-1:2005 „Elektroinstallationskanalsysteme für elektrische Installationen – Teil 1: Allgemeine Anforderungen“ benutzt werden, auf welche in dieser Norm als Teil 1 Bezug genommen wird.
Systèmes de goulottes et systèmes de conduits-profilés pour installations électriques - Partie 2-4: Règles particulières pour les colonnes de service
La présente Norme Européenne spécifie les règles et les essais pour les systèmes de goulottes (SG) et les systèmes de conduits-profilés (SCP) destinés au logement de conducteurs isolés, câbles et éventuels autres équipements électriques et si nécessaire à leur séparation de protection électrique, dans des installations électriques et/ou de systèmes de communication. La tension maximale de ces installations est de 1 000 V en courant alternatif et 1 500 V en courant continu. Les colonnes et les colonnettes sont prévues pour être montées en espace libre et au contact de la ou des surfaces de montage uniquement à une extrémité ou aux deux extrémités, le mot "montées" signifiant fixées ou placées sur le sol avec une base lestée ou reliées à une surface de montage au moyen d'un composant flexible. NOTE Les colonnes / colonnettes peuvent aussi faire partie d'un SG/SCP prévu pour être monté au mur ou au plafond et relevant de la Partie 2-1, ou prévu pour être monté au sol et relevant de la Partie 2-2, et sont alors aussi soumises à essai selon la Partie 2-1 et/ou la Partie 2-2 selon le cas. La présente Norme Européenne ne s'applique pas aux systèmes de conduit, systèmes de chemin de câble, systèmes d'échelle à câble, systèmes de canalisation préfabriquée ou aux équipements couverts par d’autres normes. La présente Norme Européenne doit être utilisée conjointement avec la EN 50085-1:2005 "Systèmes de goulottes et de conduits-profilés pour installations électriques – Partie 1: Règles générales", à laquelle il est fait référence dans ce document comme Partie 1.
Sistemi kabelskih korit in sistemi kabelskih cevi za električne inštalacije - 2-4. del: Posebne zahteve za podporne drogove
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2009
6LVWHPLNDEHOVNLKNRULWLQVLVWHPLNDEHOVNLKFHYL]DHOHNWULþQHLQãWDODFLMHGHO
3RVHEQH]DKWHYH]DSRGSRUQHGURJRYH
Cable trunking systems and cable ducting systems for electrical installations - Part 2-4:
Particular requirements for service poles
Elektroinstallationskanalsysteme für elektrische Installationen - Teil 2-4: Besondere
Anforderungen für freistehende Installationseinheiten
Systèmes de goulottes et systèmes de conduits-profilés pour installations électriques -
Partie 2-4: Règles particulières pour les colonnes de service
Ta slovenski standard je istoveten z: EN 50085-2-4:2009
ICS:
29.120.10 ,QãWDODFLMVNHFHYL]D Conduits for electrical
HOHNWULþQHQDPHQH purposes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 50085-2-4
NORME EUROPÉENNE
June 2009
EUROPÄISCHE NORM
ICS 29.120.10
English version
Cable trunking systems and cable ducting systems
for electrical installations -
Part 2-4: Particular requirements for service poles and service posts
Systèmes de goulottes Elektroinstallationskanalsysteme
et systèmes de conduits-profilés für elektrische Installationen -
pour installations électriques - Teil 2-4: Besondere Anforderungen
Partie 2-4: Règles particulières für freistehende Installationseinheiten
pour les colonnes et colonnettes
This European Standard was approved by CENELEC on 2009-05-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: Avenue Marnix 17, B - 1000 Brussels
© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50085-2-4:2009 E
Foreword
This European Standard was prepared by the Technical Committee CENELEC TC 213, Cable
management systems.
The text of the draft was submitted to the formal vote and was approved by CENELEC as
EN 50085-2-4 on 2009-05-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2010-05-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2012-05-01
This European Standard is a system standard for cable management products used for electro-
1)
technical purposes. It relates to Low Voltage Directive 2006/95/EC through consideration of the
essential requirements of this directive.
This European Standard is supported by separate standards to which references are made.
This Part 2-4 is to be used in conjunction with EN 50085-1:2005 “Cable trunking systems and cable
ducting systems for electrical installations – Part 1: General requirements”.
This Part 2-4 supplements or modifies the corresponding clauses of EN 50085-1:2005. Where a
particular clause or subclause of Part 1 is not mentioned in this Part 2-4, that clause or subclause of
Part 1 applies as far as is reasonable. Where this Part 2-4 states “addition” or “replacement”, the
relevant text of Part 1 is to be adapted accordingly.
NOTE The following numbering system is used:
– subclauses, tables and figures that are additional to those in Part 1 are numbered starting from 101;
– additional annexes are lettered AA, BB, etc.
__________
1)
Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation
of the laws of Member States relating to electrical equipment designed for use within certain voltage limits,
OJ L 374, 27.12.2006, p. 10–19.
– 3 – EN 50085-2-4:2009
Contents
Page
1 Scope . 4
2 Normative re f e r enc es . 4
3 Definitions . 5
4 General requirements . 5
5 General conditions for tests . 5
6 Classification . 6
7 Marking and documentation . 7
8 Dimensions . 7
9 Construction . 7
10 Mechanical properties . 8
11 Electrical properties . 15
12 Thermal properties . 16
13 Fire hazard . 16
14 External influences . 16
15 Electromagnetic com patibility . 17
Annex A (informative) Types of cable trunking systems (CTS) and cable ducting
systems (CDS) . 22
Annex B (informative) A-deviations . 22
Annex C (normative) CTS/CDS IK code . 22
Annex AA (normative) Use of test results according to EN 50085-2-4 for service poles
and service posts being part of a CTS/CDS intended for wall or ceiling mounting
covered by EN 50085-2-1 or floor mounting covered by EN 50085-2-2 . 23
Annex AB (normative) Routine test for the socket outlets wiring of pre-wired service
poles and service posts (correct polarity and protection against electric shock) . 26
Figures
Figure 101 − Types and application of service poles and service posts . 19
Figure 102 – Detail of the cylinder for vertical load test in accordance with 10.5.103 . 20
Figure 103 – Detail of the circular plate for vertical load test in accordance with 10.5.104 . 21
Tables
Table AA.1 – EN 50085-2-1 . 23
Table AA.2 – EN 50085-2-2 . 24
Table AB.1 – Diagrammatic representation of routine tests to be applied to the socket
outlets wiring of pre-wired service poles and service posts . 26
1 Scope
Replacement:
This European Standard specifies requirements and tests for cable trunking systems (CTS) and cable
ducting systems (CDS) intended for the accommodation, and where necessary for the electrically
protective separation, of insulated conductors, cables and possibly other electrical equipment in
electrical and/or communication systems installations. The maximum voltage of these installations is
1 000 V a.c. and 1 500 V d.c.
Service poles and service posts are intended to be mounted in free space and in contact with mounting
surface(s) only at one or two ends, where the word “mounted” means fixed or placed on the floor with a
weighted base or linked to a mounting surface through a flexible component.
NOTE Service poles and service posts can also be part of a CTS/CDS intended for wall or ceiling mounting covered by
Part 2-1 or floor mounting covered by Part 2-2 and are then also tested according to Part 2-1 and/or Part 2-2 as appropriate.
This European Standard does not apply to conduit systems, cable tray systems, cable ladder systems,
powertrack systems or equipment covered by other standards.
This European Standard shall be used in conjunction with EN 50085-1:2005 “Cable trunking systems
and cable ducting systems for electrical installations – Part 1: General requirements” which is referred
to in this document as Part 1.
2 Normative references
This clause of Part 1 is applicable except as follows:
Add the following references:
EN 20535 1994 Paper and board – Determination of water absorptiveness – Cobb
method (ISO 535:1991)
EN 50085-1 2005 Cable trunking systems and cable ducting systems for electrical
installations – Part 1: General requirements
EN 60068-2-75 1997 Environmental testing – Part 2-75: Tests – Test Eh: Hammer tests
(IEC 60068-2-75:1997)
EN 60695-11-2 2003 Fire hazard testing – Part 11-2: Test flames – 1 kW nominal pre-mixed
flame – Apparatus, confirmatory test arrangement and guidance
(IEC 60695-11-2:2003)
EN 62262 2002 Degrees of protection provided by enclosures for electrical equipment
against external mechanical impacts (IK code) (IEC 62262:2002)
EN ISO 536 1996 Paper and board – Determination of grammage (ISO 536:1995)
ISO 9328-7 2004 Steel flat products for pressure purposes – Technical delivery conditions –
Part 7: Stainless steels
– 5 – EN 50085-2-4:2009
3 Definitions
This clause of Part 1 is applicable except as follows:
Additional definitions:
3.101
service pole
CTS/CDS intended to be mounted in free space and in contact with mounting surfaces only at two
ends
NOTE 1 Service pole can be part of a CTS/CDS intended for wall, ceiling or floor mounting.
NOTE 2 The word “mounted” means fixed or placed on the floor with a weighted base or linked to a mounting surface through
a flexible component.
3.102
service post
CTS/CDS intended to be mounted in free space and in contact with mounting surface only at one end
NOTE 1 Service post can be part of a CTS/CDS intended for wall, ceiling or floor mounting.
NOTE 2 The word “mounted” means fixed or placed on the floor with a weighted base or linked to a mounting surface through
a flexible component.
3.103
pre-equipped service pole / service post
service pole / service post already assembled by the manufacturer or responsible vendor with one or
more electrical accessories and/or communication components
3.104
pre-wired service pole / service post
service pole / service post already assembled by the manufacturer or responsible vendor, wired by
means of insulated conductors and/or cables connecting one or more electrical accessories and/or
communication components
3.105
modular service pole / service post
service pole / service post which includes the assembly of two or more modules allowing to increase
the height or width or depth of the product
3.106
rated current, rated voltage
value assigned to a pre-wired and/or pre-equipped service pole / service post by the manufacturer and
to which operation and performances characteristics are referred
4 General requirements
This clause of Part 1 is applicable.
5 General conditions for tests
This clause of Part 1 is applicable except as follows:
5.1 Replace by:
5.1 Unless otherwise specified, tests according to this standard are type tests.
Additional subclause:
5.101 Unless otherwise specified in the relevant test, service poles / service posts are tested on the
longest version declared by the manufacturer and service poles / service posts which differ only by
being shorter than one which complies with the requirements for a given test are deemed to comply
with the requirements for the same test.
6 Classification
This clause of Part 1 is applicable except as follows:
6.4.1
This subclause of Part 1 is not applicable.
Additional subclauses:
6.101 According to floor treatment for service poles / service posts placed on the floor
6.101.1 Service poles / service posts for dry-treatment of floor
6.101.2 Service poles / service posts for wet-treatment of floor
6.102 According to resistance to vertical load applied through small surface area
6.102.1 CTS/CDS for 500 N
6.102.2 CTS/CDS for 750 N
6.102.3 CTS/CDS for 1 000 N
6.102.4 CTS/CDS for 1 500 N
6.102.5 CTS/CDS for 2 000 N
6.102.6 CTS/CDS for 2 500 N
6.102.7 CTS/CDS for 3 000 N
6.103 Optional classification according to resistance to vertical load applied through large
surface area
6.103.1 CTS/CDS for 2 000 N
6.103.2 CTS/CDS for 3 000 N
6.103.3 CTS/CDS for 5 000 N
6.103.4 CTS/CDS for 10 000 N
6.103.5 CTS/CDS for 15 000 N
SIS
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.