SIST EN 13999-1:2014
(Main)Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 1: General procedure
Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 1: General procedure
This European Standard describes a conventional standard method for assessing potential emissions from adhesives after their application. This European Standard applies only to “solvent-free” and “low-solvent” adhesives as they are defined in EN 923:2005+A1:2008. The adhesives shall be applicable at room temperature.
Klebstoffe - Kurzzeit-Verfahren zum Messen der Emissionseigenschaften von lösemittelarmen oder lösemittelfreien Klebstoffen nach der Applikation - Teil 1: Allgemeines Verfahren
Diese Europäische Norm beschreibt ein Konventionsverfahren zur Beurteilung potenzieller Emissionen aus Klebstoffen nach deren Applikation.
Diese Norm gilt nur für „lösemittelfreie“ und „lösemittelarme“ Klebstoffe entsprechend deren Definition in EN 923:2005+A1:2008. Die Klebstoffe müssen bei Raumtemperatur anwendbar sein.
Adhésifs - Méthode de mesurage rapide des caractéristiques émissives des adhésifs à teneur faible ou nulle en solvant après application - Partie 1 : Mode opératoire général
La présente Norme européenne décrit une méthode normalisée conventionnelle permettant d’évaluer les émissions potentielles provenant des adhésifs après leur application.
La présente Norme européenne n’est applicable qu’aux adhésifs «sans solvant» et aux adhésifs «à faible teneur en solvant», tels que définis dans l'EN 923:2005+A1:2008. Les adhésifs doivent être applicables à la température ambiante.
Lepila - Hitra metoda za merjenje emisijskih lastnosti lepil z malo topila ali brez njega po uporabi - 1. del: Splošni postopek
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Lepila - Hitra metoda za merjenje emisijskih lastnosti lepil z malo topila ali brez njega po uporabi - 1. del: Splošni postopekKlebstoffe - Kurzzeit-Verfahren zum Messen der Emissionseigenschaften von lösemittelarmen oder lösemittelfreien Klebstoffen nach der Applikation - Teil 1: Allgemeines VerfahrenAdhésifs - Méthode de mesurage rapide des caractéristiques émissives des adhésifs à teneur faible ou nulle en solvant après application - Partie 1 : Mode opératoire généralAdhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 1: General procedure83.180LepilaAdhesivesICS:Ta slovenski standard je istoveten z:EN 13999-1:2013SIST EN 13999-1:2014en,fr,de01-april-2014SIST EN 13999-1:2014SLOVENSKI
STANDARDSIST EN 13999-1:2006/AC:2007SIST EN 13999-1:20061DGRPHãþD
SIST EN 13999-1:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13999-1
December 2013 ICS 83.180 Supersedes EN 13999-1:2006English Version
Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 1: General procedure
Adhésifs - Méthode de mesurage rapide des caractéristiques émissives des adhésifs à teneur faible ou nulle en solvant après application - Partie 1 : Mode opératoire général
Klebstoffe - Kurzzeit-Verfahren zum Messen der Emissionseigenschaften von lösemittelarmen oder lösemittelfreien Klebstoffen nach der Applikation - Teil 1: Allgemeines Verfahren This European Standard was approved by CEN on 19 October 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13999-1:2013: ESIST EN 13999-1:2014
EN 13999-1:2013 (E) 2 Contents Page
Foreword .3 Introduction .5 1 Scope .6 2 Normative references .6 3 Terms and definitions .6 4 Principle .6 5 Apparatus .7 5.1 General .7 5.2 Support .7 5.3 Adhesive coating device .7 5.4 Emission test chamber .7 5.5 Air supply and mixing facilities .8 5.6 Air sampling devices .9 5.7 Devices for desorption and analysis .9 6 Adhesive sample.9 6.1 General .9 6.2 Pre-conditioning .9 6.3 Preparation of a test specimen .9 7 Procedure . 10 7.1 Number of determinations . 10 7.2 Preconditioning of the test chamber . 10 7.3 Operation of the test chamber . 10 7.4 Starting of the test . 10 7.5 Sampling and analysis of emitted substances . 10 8 Expression of results . 11 8.1 Calculations . 11 8.2 Carcinogenic and sensitizing compounds concentration . 11 8.3 Volatile organic compounds . 11 8.3.1 General . 11 8.3.2 Determination of the specific emission rate at the sampling times . 11 8.3.3 Determination of the empirical parameters a and b . 12 9 Test report . 13 Annex A (normative)
Carcinogenic and sensitizing substances . 14 Bibliography . 15
SIST EN 13999-1:2014
EN 13999-1:2013 (E) 3 Foreword This document (EN 13999-1:2013) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2014, and conflicting national standards shall be withdrawn at the latest by June 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13999-1:2006. EN 13999-1:2013 includes the following significant technical changes with respect to EN 13999-1:2006: a) In general, the text is adapted to the new CLP Regulation No 1272/2008 [11]. b) In 6.3, a new Note 2 is added, emphasizing the need that materials be tested under same conditions using the spreading techniques and the coat weights specific for each application. c) In 7.5, the sampling time is changed (the sampling time at 24 h is eliminated, a sampling time at 72 h is added), and a note is added concerning the possibility of other sampling times, e.g. after 28 days. d) “Specific cumulative emission” (previous 8.3.3) is eliminated. e) The examples from Note to Annex A are eliminated. EN 13999, under the general title Adhesives -term method for measuring the emission properties of low-solvent or solvent-free adhesives after application, consists of the following parts: — mart k: deneral procedure — mart l: aetermination of volatile organic compounds — mart m: aetermination of volatile aldehydes — mart 4: aetermination of volatile diisocyanates SAFETY STATEMENT — Persons using this document should be familiar with the normal laboratory practice, if applicable. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any regulatory conditions. ENVIRONMENTAL STATEMENT — It is understood that some of the material permitted in this European Standard may have negative environmental impact. As technological advantages lead to acceptable alternatives for these materials, they will be eliminated from this European Standard to the extent possible. At the end of the test, the user of this European Standard should take care to carry out an appropriate disposal of the wastes, according to local regulation. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, SIST EN 13999-1:2014
EN 13999-1:2013 (E) 4 Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 13999-1:2014
EN 13999-1:2013 (E) 5 Introduction Solvent-free and low-solvent adhesives may release considerable long-term emissions of volatile chemical compounds. Any documentation of emission characteristics requires a test method that includes all relevant and potentially hazardous substances. It is essential that the test — be reliable and reproducible, — give results in a short time to be useful for decisions for development projects, — verify that carcinogenic or sensitizing volatile substances are substantially absent, — characterize the emission properties of the adhesive. This can be achieved by sampling the atmosphere around the applied adhesive kept in an environmental test chamber at controlled ambient conditions. SIST EN 13999-1:2014
EN 13999-1:2013 (E) 6 1 Scope This European Standard describes a conventional standard method for assessing potential emissions from adhesives after their application. This European Standard applies only to “solvent-free” and “low-solvent” adhesives as they are defined in EN 923:2005+A1:2008. The adhesives shall be applicable at room temperature. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 923:2005+A1:2008, Adhesives — Terms and definitions EN 1067, Adhesives — bxamination and preparation of samples for testing EN 13999-2, Adhesives — phort term method for measuring the emission properties of low-solvent or solvent-free adhesives after application — mart l: aetermination of volatile organic compounds EN 13999-3, Adhesives — phort term method for measuring the emission properties of low-solvent or solvent-free adhesives after application — mart m: aetermination of volatile aldehydes EN 13999-4, Adhesives — phort term method for measuring the emission properties of low-solvent or solvent-free adhesives after application — mart 4: aetermination of volatile diisocyanates EN ISO 15605, Adhesives — pampling bfpl kopMoc EN ISO 16000-9:2006, fndoor air — mart 9: aetermination of the emission of volatile organic compounds from building products and furnishing — bmission test chamber method bfpl kpMMM-9:lMMpc ISO 554, ptandard atmospheres for conditioning and/or testing — ppecifications ISO 16000-6:2011, fndoor air — mart p: aetermination of volatile organic compounds in indoor and test chamber air by active sampling on Tenax TA® sorbentf thermal desorption and gas chromatography using Mp or Mp-cfa 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 923:2005+A1:2008, EN ISO 16000-9:2006 and ISO 16000-6:2011 and the following apply. 3.1 volatile organic compounds VOC all volatile organic compounds eluting between and including n-hexane and n-hexadecane on a gas chromatographic column Note 1 to entry: The measurement is carried out using a capillary column coated with 5 % phenyl / 95 % methyl-poly-siloxane. 4 Principle The test determines the emissions of volatile organic substances from adhesive coatings. Very volatile and mainly particle bound compounds are not detected with the described procedures. The test is performed in an SIST EN 13999-1:2014
EN 13999-1:2013 (E) 7 emission test chamber (Figure 1) at specified constant temperature, relative humidity, air mixing and air exchange. A measurement of the concentrations of the compounds of interest in the air of the exhaust pipe is considered representative of the air in the whole test chamber. Sampling and analysis of the non-polar and slightly polar volatile organic compounds, as defined in ISO 16000-6, shall be carried out as described in EN 13999-2. Sampling and analysis of the volatile aldehydes shall be carried out as described in EN 13999-3. Sampling and analysis of the volatile isocyanates shall be carried out as described in EN 13999-4. The test includes: — qualitative and quantitative determination of carcinogenic and sensitizing substances in an early stage after the application of the adhesive sample, — determination of the VOC specific emission rate at two points of time. NOTE There are specific applications for which an emission test cell (as described in EN ISO 16000-10 [9]) can be easier to handle than the emission test chamber, for instance when a sample is too small to be properly applied into the test chamber. In these cases, it is possible to apply the procedures as given in this European Standard with the exception that a test cell is used instead of the test chamber. However, as the air flow rate across the sample is higher than with the chamber method, the results can only be used with supporting correlation data. 5 Apparatus 5.1 General The test apparatus shall be comprised of the following main components: support, air supply and mixing facilities, emission test chamber with monitoring and control systems, air sampling devices and devices for desorption and analysis. 5.2 Support A clean stainless steel plate or a glass plate shall be u
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.