SIST EN 2046:2004
(Main)Aerospace series - Hexagonal bars, drawn in aluminium and aluminium alloys - Tolerance class h 11 - Width across flats 7 mm < a < 50 mm - Dimensions
Aerospace series - Hexagonal bars, drawn in aluminium and aluminium alloys - Tolerance class h 11 - Width across flats 7 mm < a < 50 mm - Dimensions
This standard specifies the dimensions and tolerances of:
Hexagonal bars, drawn
in aluminium and aluminium alloys
Tolerance class h 11
Width across flats 7 mm < a < 50 mm
for aerospace applications.
Luft- und Raumfahrt - Sechskantstangen, gezogen aus Aluminium und Aluminiumlegierungen - Toleranzklasse h 11 - Schlüsselweite 7 mm < a < 50 mm - Maße
Diese Norm legt die Maße und Toleranzen von
Sechskantstangen, gezogen
aus Aluminium und Aluminiumlegierungen
Toleranzklasse h 11
Schlüsselweite 7 mm < a < 50 mm
für die Luft- und Raumfahrt fest.
Série aérospatiale - Barres hexagonales, étirées en aluminium et alliages d'aluminium - Classe de tolérance h 11 - Surplats 7 mm < a < 50 mm - Dimensions
La présente norme spécifie les dimensions et les tolérances des :
Barres hexagonales, étirées
en aluminium et alliages d'aluminium
Classe de tolérance h 11
Surplats 7 mm < a < 50 mm
pour applications aérospatiales.
Aerospace series - Hexagonal bars, drawn in aluminium and aluminium alloys - Tolerance class h 11 - Width across flats 7 mm < a < 50 mm - Dimensions
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Hexagonal bars, drawn in aluminium and aluminium alloys - Tolerance class h 11 - Width across flats 7 mm < a < 50 mm - DimensionsLuft- und Raumfahrt - Sechskantstangen, gezogen aus Aluminium und Aluminiumlegierungen - Toleranzklasse h 11 - Schlüsselweite 7 mm < a < 50 mm - MaßeSérie aérospatiale - Barres hexagonales, étirées en aluminium et alliages d'aluminium - Classe de tolérance h 11 - Surplats 7 mm < a < 50 mm - DimensionsAerospace series - Hexagonal bars, drawn in aluminium and aluminium alloys - Tolerance class h 11 - Width across flats 7 mm < a < 50 mm - Dimensions49.025.20AluminijAluminiumICS:Ta slovenski standard je istoveten z:EN 2046:2001SIST EN 2046:2004en01-maj-2004SIST EN 2046:2004SLOVENSKI
STANDARD
SIST EN 2046:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2046December 2001ICS 49.025.20English versionAerospace series - Hexagonal bars, drawn in aluminium andaluminium alloys - Tolerance class h 11 - Width across flats 7mm
a
50 mm - DimensionsSérie aérospatiale - Barres hexagonales, étirées enaluminium et alliages d'aluminium - Classe de tolérance h11 - Surplats 7 mm
a
50 mm - DimensionsLuft- und Raumfahrt - Sechskantstangen, gezogen ausAluminium und Aluminiumlegierungen - Toleranzklasse h11 - Schlüsselweite 7 mm
a
50 mm - MaßeThis European Standard was approved by CEN on 2 May 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2046:2001 ESIST EN 2046:2004
EN 2046:2001 (E)2ForewordThis European Standard has been prepared by the European Association of Aerospace Manufacturers(AECMA).After inquiries and votes carried out in accordance with the rules of this Association, this Standard hasreceived the approval of the National Associations and the Official Services of the member countries ofAECMA, prior to its presentation to CEN.This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by June 2002, and conflicting national standards sh
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.