SIST EN ISO 8130-8:2021
(Main)Coating powders - Part 8: Assessment of the storage stability of thermosetting powders (ISO 8130-8:2021)
Coating powders - Part 8: Assessment of the storage stability of thermosetting powders (ISO 8130-8:2021)
This document establishes a method for the estimation of the storage stability of thermosetting
coating powders. It provides the procedures for determining the changes both in the physical state
of a thermosetting coating powder and in its chemical reactivity, together with its capacity to form a
satisfactory final coating.
Pulverlacke - Teil 8: Beurteilung der Lagerbeständigkeit von wärmehärtenden Pulverlacken (ISO 8130-8:2021)
Dieses Dokument legt ein Verfahren zum Bewerten der Lagerbeständigkeit von wärmehärtenden Pulverlacken fest. Es liefert die Verfahren zum Bestimmen der Änderungen sowohl des physikalischen Zustandes eines wärmehärtenden Pulverlackes als auch seiner chemischen Reaktivität, zusammen mit dessen Fähigkeit, eine zufrieden stellende Beschichtung zu ergeben. Eine Korrelation zwischen Änderungen unterschiedlicher Eigenschaften ist nicht zu erwarten. In ähnlicher Weise braucht keine Korrelation zwischen den Ergebnissen vorhanden zu sein, die bei unterschiedlichen Lagerbedingungen erhalten wurden.
Die Ergebnisse der in diesem Dokument festgelegten Verfahren geben einen Hinweis darauf, ob ein Pulverlack den Einflüssen durch eine Lagerung vor dem Auftragen standhält.
Poudres pour revêtement - Partie 8: Estimation de la stabilité au stockage des poudres thermodurcissables (ISO 8130-8:2021)
Le présent document établit une méthode d'estimation de la stabilité au stockage des poudres pour revêtement thermodurcissables. Elle fournit les modes opératoires à suivre pour déterminer les changements intervenant à la fois dans l'état physique d'une poudre pour revêtement thermodurcissable et dans sa réactivité chimique, ainsi que sa capacité à former un revêtement final satisfaisant.
Praškasti premazi - 8. del: Ocena stabilnosti termoreaktivnih praškov pri skladiščenju (ISO 8130-8:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8130-8:2021
01-september-2021
Nadomešča:
SIST EN ISO 8130-8:2013
Praškasti premazi - 8. del: Ocena stabilnosti termoreaktivnih praškov pri
skladiščenju (ISO 8130-8:2021)
Coating powders - Part 8: Assessment of the storage stability of thermosetting powders
(ISO 8130-8:2021)
Pulverlacke - Teil 8: Beurteilung der Lagerbeständigkeit von wärmehärtenden
Pulverlacken (ISO 8130-8:2021)
Poudres pour revêtement - Partie 8: Estimation de la stabilité au stockage des poudres
thermodurcissables (ISO 8130-8:2021)
Ta slovenski standard je istoveten z: EN ISO 8130-8:2021
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 8130-8:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8130-8:2021
---------------------- Page: 2 ----------------------
SIST EN ISO 8130-8:2021
EN ISO 8130-8
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2021
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 8130-8:2010
English Version
Coating powders - Part 8: Assessment of the storage
stability of thermosetting powders (ISO 8130-8:2021)
Poudres pour revêtement - Partie 8: Estimation de la Pulverlacke - Teil 8: Beurteilung der
stabilité au stockage des poudres thermodurcissables Lagerbeständigkeit von wärmehärtenden Pulverlacken
(ISO 8130-8:2021) (ISO 8130-8:2021)
This European Standard was approved by CEN on 28 April 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8130-8:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8130-8:2021
EN ISO 8130-8:2021 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8130-8:2021
EN ISO 8130-8:2021 (E)
European foreword
This document (EN ISO 8130-8:2021) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2022, and conflicting national standards shall
be withdrawn at the latest by January 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8130-8:2010.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN websites.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 8130-8:2021 has been approved by CEN as EN ISO 8130-8:2021 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8130-8:2021
---------------------- Page: 6 ----------------------
SIST EN ISO 8130-8:2021
INTERNATIONAL ISO
STANDARD 8130-8
Second edition
2021-06
Coating powders —
Part 8:
Assessment of the storage stability of
thermosetting powders
Poudres pour revêtement —
Partie 8: Estimation de la stabilité au stockage des poudres
thermodurcissables
Reference number
ISO 8130-8:2021(E)
©
ISO 2021
---------------------- Page: 7 ----------------------
SIST EN ISO 8130-8:2021
ISO 8130-8:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 8130-8:2021
ISO 8130-8:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Test panels . 2
7 Sampling . 2
8 Procedure. 2
8.1 Preliminary examination . . 2
8.1.1 Determination of initial chemical reactivity of the powder. 2
8.1.2 Determination of initial properties of the coating . 3
8.2 Artificial-storage treatment . 3
8.3 Final examination . 3
8.3.1 General. 3
8.3.2 Change in appearance of the powder . 3
8.3.3 Determination of chemical reactivity of the powder . 3
8.3.4 Determination of properties of the coating prepared from the coating
powder after storage . 4
9 Expression of results . 4
10 Precision . 4
11 Test report . 4
© ISO 2021 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 8130-8:2021
ISO 8130-8:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the vo
...
SLOVENSKI STANDARD
oSIST prEN ISO 8130-8:2020
01-november-2020
Praškasti premazi - 8. del: Ocena stabilnosti termoreaktivnih praškov pri
skladiščenju (ISO/DIS 8130-8:2020)
Coating powders - Part 8: Assessment of the storage stability of thermosetting powders
(ISO/DIS 8130-8:2020)
Pulverlacke - Teil 8: Beurteilung der Lagerbeständigkeit von wärmehärtenden
Pulverlacken (ISO/DIS 8130-8:2020)
Poudres pour revêtement - Partie 8: Estimation de la stabilité au stockage des poudres
thermodurcissables (ISO/DIS 8130-8:2020)
Ta slovenski standard je istoveten z: prEN ISO 8130-8
ICS:
87.040 Barve in laki Paints and varnishes
oSIST prEN ISO 8130-8:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 8130-8:2020
---------------------- Page: 2 ----------------------
oSIST prEN ISO 8130-8:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8130-8
ISO/TC 35/SC 9 Secretariat: BSI
Voting begins on: Voting terminates on:
2020-09-22 2020-12-15
Coating powders —
Part 8:
Assessment of the storage stability of thermosetting
powders
Poudres pour revêtement —
Partie 8: Estimation de la stabilité au stockage des poudres thermodurcissables
ICS: 87.040
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
This document is circulated as received from the committee secretariat.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8130-8:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020
---------------------- Page: 3 ----------------------
oSIST prEN ISO 8130-8:2020
ISO/DIS 8130-8:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 8130-8:2020
ISO/DIS 8130-8:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Test panels . 2
7 Sampling . 2
8 Procedure. 3
8.1 Preliminary examination . . 3
8.1.1 Determination of initial chemical reactivity of the powder. 3
8.1.2 Determination of initial properties of the coating . 3
8.2 Artificial-storage treatment . 3
8.3 Final examination . 3
8.3.1 General. 3
8.3.2 Change in appearance of the powder . 3
8.3.3 Determination of chemical reactivity of the powder . 4
8.3.4 Determination of properties of the coating prepared from the coating
powder after storage . 4
9 Expression of results . 4
10 Precision . 4
11 Test report . 4
© ISO 2020 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 8130-8:2020
ISO/DIS 8130-8:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and vanishes.
This second edition cancels and replaces the first edition (ISO 8130-8:1994), which has been technically
revised. The main changes compared to the previous edition are as follows:
a) Clause 3 on terms and definitions has been added;
b) pretreated aluminium panels have been added in Clause 6 as another option for test panels;
c) Table 1 describing four different ratings for the extent of compaction of agglomeration of the
coating powder has been deleted;
d) the required supplementary information (former Clause 4 and Annex A) has been incorporated in
the test report;
e) the text has been editorially revised and the normative references have been updated.
A list of all parts in the ISO 8130 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html
iv © ISO 2020 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 8130-8:2020
ISO/DIS 8130-8:2020(E)
Introduction
Coating powders are subject to two distinct ageing mechanisms, one involvi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.