oSIST prEN 15502-2-2:2022
(Main)Gas-fired central heating boilers - Part 2-2: Specific standard for type B1 appliances
Gas-fired central heating boilers - Part 2-2: Specific standard for type B1 appliances
This European Standard specifies, the requirements and test methods concerning the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners and are hereafter referred to as 'boilers'.
Where the word boiler is used, this is to be read as the boiler including its connecting ducts, ducts and terminals, if any.
This document is to be used in conjunction with FprEN 15502-1:2021
This European Standard covers gas-fired central heating boilers type B11, B11BS, B12, B12BS, B13, B13BS:
NOTE For further background information on appliance types see EN 1749:2020
a) that have a nominal heat input (on the basis of net calorific value) not exceeding 70 kW;
b) that use one or more combustible gases of the three gas families at the pressures stated in EN 437:2018;
c) where the temperature of the heat transfer fluid does not exceed 105 °C during normal operation;
d) where the maximum operating pressure in the water circuit does not exceed 6 bar;
e) which are declared in the technical instructions to be either a 'low temperature boiler' or a 'standard boiler'. If no declaration is given the boiler is to be considered a 'standard boiler';
f) which are intended to be installed inside a building or in a partially protected place;
g) which are intended to produce also hot water either by the instantaneous or storage principle, as a single unit.
h) which are designed for either sealed water systems or for open water systems.
For applications within the scope of the PED further requirements may be necessary (e.g. situations where the maximum allowable temperature exceeds 110 °C, or where volume times maximum allowable pressure is over 50 bar x litres).
NOTE This standard provides requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard, the risk associated with this alternative construction needs to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This standard does not cover all the requirements for:
i) appliances that are intended to be connected to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex AB);
j) appliances using flue dampers;
k) appliances that have a nominal heat input (on the basis of net calorific value) exceeding 70 kW;
l) appliances of the types A, B14, B2, B3, B4, B5 and C;
m) appliances intended to be connected to a (common) flue having mechanical extraction;
n) appliances with gas/air ratio control;
o) modular boilers;
p) boilers which can give rise to condensation under certain circumstances;
q) boilers intended to be installed in a room with a foreseeable negative pressure relative to the pressure in the flue system;
r) surface temperatures of external parts particular to children and elderly people;
s) appliances that are intended to burn natural gases of the second family where hydrogen is added to the natural gass;
t) boilers intended to be installed in areas accessible to elderly people and children.
NOTE Negative pressure relative to the pressure in the flue system can for example be caused by mechanical or thermal ventilation in airtight buildings.
Heizkessel für gasförmige Brennstoffe - Teil 2-2: Heizkessel der Bauart B1
Dieses Dokument legt die Anforderungen und Prüfverfahren für die Einteilung und Kennzeichnung von gasbefeuerten Zentralheizungskesseln fest, die mit atmosphärischen Brennern mit oder ohne Ventilator ausgerüstet sind und nachfolgend kurz „Kessel“ genannt werden.
Wenn das Wort Kessel benutzt wird, muss es als Kessel einschließlich seiner Verbindungsstücke, Rohr und Windschutzeinrichtung, falls vorhanden, gelesen werden.
Dieses Dokument ist in Verbindung mit EN 15502 1:2021 anzuwenden.
Diese Europäische Norm gilt für gasbefeuerte Zentralheizungskessel der Bauart B11, B11BS, B12, B12BS, B13, B13BS:
ANMERKUNG 1 Für weitere Hintergrundinformationen zu Gerätearten siehe EN 1749:2020.
a) die eine Nennwärmebelastung (bezogen auf den unteren Heizwert) von nicht mehr als 70 kW haben;
b) die mit einem oder mehreren brennbaren Gasen der drei Gasfamilien mit den in EN 437:2021 genannten Drücken betrieben werden;
c) bei denen die Temperatur der wärmeleitenden Flüssigkeit unter normalen Betriebsbedingungen 105 °C nicht überschreitet;
d) deren maximaler Betriebsdruck im Wasserkreislauf 6 bar nicht überschreitet;
e) die vom Hersteller entweder als "Niedertemperaturkessel" oder als "Standardkessel" bezeichnet werden. Wenn keine Angabe gemacht wird, wird der Kessel als "Standardkessel" betrachtet;
f) die für die Aufstellung im Inneren eines Gebäudes oder an einem teilweise geschützten Ort vorgesehen sind;
g) die dafür vorgesehen sind, nach dem Durchlaufprinzip oder nach dem Speicherprinzip Warmwasser herzustellen, wobei das Ganze als eine Einheit vertrieben wird;
h) die für geschlossene oder offene Wassersysteme ausgelegt sind.
Für Anwendungen innerhalb des Anwendungsbereiches der Druckgeräterichtlinie (DGRL, en: PED) können weitere Anforderungen erforderlich werden (z. B. Situationen, bei denen die höchstzulässige Temperatur 110 °C überschreitet, oder wenn der Wert Volumen mal höchstzulässiger Druck über 50 bar x Liter liegt).
ANMERKUNG 2 Dieses Dokument enthält Anforderungen an Kessel mit bekannter Bauweise. Für Kesseln mit alternativer Bauweise, die eventuell nicht vollständig durch diese Norm abgedeckt werden, bedarf das Risiko, das mit dieser alternativen Bauweise verbunden ist, einer Abschätzung.
Ein Beispiel für eine auf einer Risikoanalyse beruhenden Bewertungsmethode wird in Abschnitt 11 beschrieben.
Diese Norm behandelt nicht alle Anforderungen für:
aa) Geräte, die dafür ausgelegt sind, an ein Gasnetz angeschlossen zu werden, bei dem die Qualität des verteilten Gases über die Lebensdauer des Gerätes wahrscheinlich stark schwankt (siehe Anhang AB);
ab) Geräte, die Abgasklappen benutzen;
ac) Geräte, die eine Nennwärmebelastung (auf Basis des Heizwerts) nicht über 70 kW haben.
ad) Geräte der Bauarten A, B14, B2, B3, B4, B5 und C;
ae) Geräte, die an eine (gemeinsame) Abgasanlage mit mechanischer Abgasabführung anzuschließen sind;
af) Geräte mit Brenngas/Luft-Regelung;
ag) Modulierende Brenner;
ah) Kessel, bei denen bei bestimmten Bedingungen es zur Kondensation führen kann;
ai) Kessel, die für die Innenaufstellung vorgesehen sind mit einem negativen Druck im Vergleich zum Druck im Abgassystem.
aj) Oberflächentemperaturen von Außenteilen, insbesondere für Kinder und ältere Menschen;
ak) Geräte, die für die Verbrennung von Erdgas der zweiten Familie bestimmt sind und bei denen dem Erdgas Wasserstoff zugesetzt wird;
al) Kessel, die speziell für die Installation in Bereichen, die für ältere Menschen und Kinder zugänglich sind, vorgesehen sind;
am) Kessel, die mit einer adaptiven Verbrennungsregelung (ACCF, en: adaptive combustion control function) ausgestattet sind.
ANMERKUNG Negativer Druck im Vergleich zum Druck im Abgassystem kann zum Beispiel durch mechanische oder thermische Lüftung in luftdichten Gebäuden hervorgerufen werden.
Chaudières de chauffage central utilisant les combustibles gazeux - Partie 2-2: Norme spécifique pour les appareils de type B1
Le présent document spécifie les exigences et les méthodes d’essai concernant la classification et le marquage des chaudières de chauffage central utilisant les combustibles gazeux et équipées de brûleurs atmosphériques ou de brûleurs atmosphériques assistés d’un ventilateur, ci après dénommées « chaudières ».
Lorsque le terme chaudière est utilisé, il doit être interprété comme étant la chaudière, y compris ses conduits de raccordement, conduits et terminaux, s’il y a lieu.
Le présent document doit être utilisé conjointement avec l’EN 15502-1:2021.
La présente Norme européenne couvre les chaudières de chauffage central utilisant les combustibles gazeux de types B11, B11BS, B12, B12BS, B13 et B13BS :
NOTE 1 Pour de plus amples informations sur la structure des types d’appareils, voir l’EN 1749:2020.
a) dont le débit calorifique nominal (basé sur le pouvoir calorifique inférieur) est inférieur ou égal à 70 kW ;
b) utilisant un ou plusieurs combustibles gazeux appartenant aux trois familles de gaz et aux pressions indiquées dans l’EN 437:2021 ;
c) dont la température du fluide caloporteur ne dépasse pas 105 °C en fonctionnement normal ;
d) dont la pression maximale de service dans le circuit d’eau ne dépasse pas 6 bar ;
e) déclarées comme étant des « chaudières à basse température » ou des « chaudières standard » dans la notice technique. Si aucune déclaration n'est faite, la chaudière doit être considérée comme une « chaudière standard » ;
f) destinées à être installées dans un bâtiment ou à un emplacement partiellement protégé ;
g) destinées à produire aussi instantanément de l’eau chaude ou capables de la stocker, sous forme monobloc ;
h) conçues pour des circuits d’eau fermés ou ouverts.
Pour les utilisations entrant dans le domaine d'application de la Directive 97/23/CE pour les équipements sous pression, des exigences supplémentaires peuvent être nécessaires (par exemple dans des situations où la température admissible maximale dépasse 110 °C, ou lorsque le produit volume par pression maximale admissible est supérieur à 50 bar x litre).
NOTE 2 Le présent document fournit des exigences pour les chaudières dont la construction est connue. Pour les chaudières de construction différente susceptibles de ne pas être traitées par la présente norme, le risque associé à cette construction différente nécessite d’être évalué.
L’Article 11 donne un exemple de méthodologie d’évaluation basée sur l’évaluation des risques.
La présente norme ne couvre pas toutes les exigences concernant :
aa) les appareils destinés à être raccordés à des réseaux de distribution de gaz où la qualité du gaz distribué est susceptible de varier considérablement tout au long de la durée de vie de l'appareil (voir Annexe AB) ;
ab) les appareils utilisant des registres de tirage ;
ac) les appareils dont le débit calorifique nominal (basé sur le pouvoir calorifique inférieur) est supérieur à 70 kW ;
ad) les appareils de types A, B14, B2, B3, B4, B5 et C ;
ae) les appareils destinés à être raccordés à une cheminée (commune) à extraction mécanique ;
af) les appareils avec un dispositif de régulation du rapport air/gaz.
ag) les chaudières modulaires ;
ah) les chaudières pouvant condenser dans certaines circonstances ;
ai) les chaudières destinées à être installées dans un local avec une pression négative prévisible par rapport à la pression dans le système d’évacuation des produits de combustion ;
aj) les températures de surface des parties extérieures en particulier exposées aux enfants et aux personnes âgées ;
ak) les appareils destinés à brûler des gaz naturels de la deuxième famille lorsque de l’hydrogène est ajouté au gaz naturel ;
al) les chaudières destinées à être installées dans des zones accessibles aux personnes âgées et aux [...]
Plinski kotli za centralno ogrevanje - 2-2. del: Poseben standard za tip kotlov B1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 15502-2-2:2022
01-december-2022
Plinski kotli za centralno ogrevanje - 2-2. del: Poseben standard za tip kotlov B1
Gas-fired central heating boilers - Part 2-2: Specific standard for type B1 appliances
Heizkessel für gasförmige Brennstoffe - Teil 2-2: Heizkessel der Bauart B1
Chaudières de chauffage central utilisant les combustibles gazeux - Partie 2-2: Norme
spécifique pour les appareils de type B1
Ta slovenski standard je istoveten z: prEN 15502-2-2
ICS:
91.140.10 Sistemi centralnega Central heating systems
ogrevanja
97.100.20 Plinski grelniki Gas heaters
oSIST prEN 15502-2-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 15502-2-2:2022
---------------------- Page: 2 ----------------------
oSIST prEN 15502-2-2:2022
DRAFT
EUROPEAN STANDARD
prEN 15502-2-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2022
ICS 27.060.30; 91.140.10 Will supersede EN 15502-2-2:2014
English Version
Gas-fired central heating boilers - Part 2-2: Specific
standard for type B1 appliances
Chaudières de chauffage central utilisant les Heizkessel für gasförmige Brennstoffe - Teil 2-2:
combustibles gazeux - Partie 2-2: Norme spécifique Heizkessel der Bauart B1
pour les appareils de type B1
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 109.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15502-2-2:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 15502-2-2:2022
prEN 15502-2-2:2022 (E)
Contents Page
European foreward
European foreword . 5
Introduction . 9
1 Scope . 10
2 Normative references . 11
3 Terms, definitions and symbols . 11
3.1 Terms and definitions . 11
3.2 Symbols . 11
4 Classification . 11
5 Construction . 12
5.1 General . 12
5.2 Conversion to different gases . 12
5.3 Materials . 12
5.3.1 General . 12
5.3.2 Materials and thicknesses of walls or tubes with water side operating pressure for
boilers of pressure class-3 . 12
5.3.3 Domestic water connections . 12
5.3.4 Thermal insulation . 12
5.3.5 Materials in contact with water for human consumption . 12
5.3.6 Durability against corrosion of metallic combustion product circuits . 12
5.4 Method of construction . 12
5.4.1 Design . 12
5.4.2 Checking the state of operation . 12
5.4.3 Use and servicing. 12
5.4.4 Connections to the gas and water pipes . 12
5.4.5 Soundness . 13
5.4.6 Supply of combustion air and evacuation of the combustion products . 13
5.4.7 Dampers . 13
5.4.8 Air proving for type B and B boilers. 13
12 13
5.4.9 Gas/air ratio controls for type B and B boilers . 13
12 13
5.4.10 Fan for type B and B boilers . 13
12 13
5.4.11 Drainage . 13
5.4.12 Operational safety in the event of failure of the auxiliary energy . 13
5.4.13 Special provision for low temperature boilers and condensing boilers . 13
5.5 Burners . 13
5.6 Pressure test points. 13
5.7 Requirements for the application of control and safety devices . 13
5.8 Additional requirements for modular boilers . 14
6 Electrical and electromagnetic safety . 14
7 Controls . 14
8 Operational requirements . 15
2
---------------------- Page: 4 ----------------------
oSIST prEN 15502-2-2:2022
prEN 15502-2-2:2022 (E)
8.1 General . 15
8.1.1 Characteristics of the reference and limit gases . 15
8.1.2 General test conditions . 15
8.2 Soundness . 16
8.2.1 Soundness of the gas circuit . 16
8.2.2 Soundness of the combustion circuit . 16
8.2.3 Soundness of the water circuit . 17
8.2.4 Soundness of the domestic water circuit . 17
8.3 Hydraulic resistance . 17
8.4 Heat inputs and heat output . 17
8.5 Limiting temperatures . 17
8.5.1 General . 17
8.5.2 Limiting temperatures of the adjusting, control and safety devices . 17
8.5.3 Limiting temperatures of the side walls, the front and the top . 17
8.5.4 Limiting temperatures of the test panels and the floor . 18
8.6 Ignition, cross lighting, flame stability . 18
8.6.1 General . 18
8.6.2 Limit conditions . 18
8.6.3 Special flue conditions . 18
8.6.4 Reduction of the gas rate of the ignition burner . 18
8.7 Reduction of the gas pressure . 19
8.8 Defective closure of the gas valve immediately upstream of the main burner . 19
8.9 Pre-purge . 19
8.10 Functioning of a permanent ignition burner when the fan stops during the standby
time . 21
8.11 Adjustment, control and safety devices . 21
8.12 Carbon monoxide . 23
8.13 NO . 23
x
8.14 Special provisions for boilers intended to be installed in a partially protected place . 24
8.15 Formation of condensate . 24
8.16 Temperature of combustion products . 24
8.17 Sound power level L . 25
WA
9 Useful efficiencies . 26
9.1 General . 26
9.2 Useful efficiency at the nominal heat input . 26
9.2.1 Requirements . 26
9.2.2 Tests . 26
9.3 Useful efficiency at part load . 26
9.3.1 Requirements . 26
9.3.2 Tests . 26
9.4 Heat output, seasonal energy efficiency and energy consumption . 26
10 Electric auxiliary energy . 27
11 Risk assessment . 27
12 Marking and instructions . 27
12.1 Boiler marking . 27
12.1.1 Data plate . 27
12.1.2 Markings related to the state of adjustment . 27
12.1.3 Packaging . 27
12.1.4 Warnings notices on the boiler and the packaging . 27
12.1.5 Other information . 27
12.2 Instructions . 28
3
---------------------- Page: 5 ----------------------
oSIST prEN 15502-2-2:2022
prEN 15502-2-2:2022 (E)
12.2.1 Instructions for installation . 28
12.2.2 Instructions for use and servicing. 29
12.2.3 Conversion instruction. 29
12.3 Presentation . 29
101 Figures . 29
102 Listing of tables and numbers . 36
103 Annexes . 36
Annex I (informative) Compilation of the test conditions for the various gas families . 38
Annex ZA (informative) Left empty on purpose . 43
Annex ZB (informative) Clauses of this European standard addressing the methods for the
verification of the efficiency of the EU Directive 92/42/EEC, relating to the efficiency
of new hot boilers with an output of 4 kW – 400 kW . 44
Annex ZC (informative) Relationship between this European Standard and the ecodesign
requirements of Commission Regulation (EU) No 813/2013 L 239/136 aimed to be
covered. 45
Annex ZD (informative) Relationship between this European Standard and the energy
labelling requirements of Commission Delegated Regulation (EU) No 811/2013 L
239/1 aimed to be covered . 48
Annex ZE (informative) Relationship between this European Standard and the essential
requirements of Regulation (EU) 2016/426 of the European Parliament and of the
Council of 9 March 2016 on appliances burning gaseous fuels and repealing
Directive 2009/142/EC aimed to be covered . 51
Bibliography . 64
4
---------------------- Page: 6 ----------------------
oSIST prEN 15502-2-2:2022
prEN 15502-2-2:2022 (E)
European foreword
This document (prEN 15502-2-2:2022) has been prepared by Technical Committee CEN/TC 109
“Central heating boilers using gaseous fuels”, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 15502-2-2:2014.
The main technical changes compared to EN 15502-2-2:2014 are the following:
I) Resulting from the revision of EN 15502-1 into EN 15502-1:2021:
a) technical changes related to eco-design and energy labelling for appliances ≤ 400 kW:
1) deletion of the requirements that can be found in the legislation itself;
2) modification of the Annexes ZC and ZD;
b) new or generally reworded requirements:
1) separation between requirements and test methods in to different clauses;
2) moving additional common parts from EN 15502-2-1:2012+A1:2016 and/or EN 15502-2-
2:2014 to EN 15502-1:2021 (for example all definitions used in the parts 2 are moved to
part 1; Therefore most of the definitions in this part are now by reference to part 1);
3) Definitions added for Instructions for installation, Instructions for use and servicing, and
Technical documentation and consequently applied throughout the document;
4) Improved wording of definitions related to the air supply and combustion products circuit;
5) Improved the references of the annexes Z. The annex Z referring to the GAD has been
removed and an annex Z referring to the GAR has been inserted;
6) Only "instructions for installation" and "instructions for use and servicing" are defined.
Therefore, these are the only instructions to be used in this standard;
7) improved definitions 'ducts / circuits';
8) definition weighted value of the NOx concentration added. With regard to Ecodesign, it is
clarified that the emissions declared are the emissions when using the references gases;
c) limitation of the scope compared to the standards superseded by the EN 15502 series (that
were cited in the OJEU under the GAD):
5
---------------------- Page: 7 ----------------------
oSIST prEN 15502-2-2:2022
prEN 15502-2-2:2022 (E)
1
1) Types B14 and B4 appliances, as covered in EN 297:1994 are not covered by this
standard as there seems to be a limited market for these appliances due to the introduction
of the Ecodesign Directive that only has an exemption for B11 appliances;
NOTE B14 and B4 are non-condensing appliances.
2) this document does not cover all the requirements for appliances designed and
constructed to burn gas containing toxic components. In the past it was always considered
that the gases were not toxic, however this was never clearly indicated in the scope. In fact
this is not a change of scope, but a clarification of the scope;
3) this document is not intended to cover appliances intended for connection to gas grids
where the quality of the distributed gas is likely to vary to a large extent over the lifetime
of the appliance (see Annex AB). In the past no big variation in gas quality occurred. Due to
the EASEE-gas CBP wide variations of gas quality are considered. As these were never
covered in this standard, the scope is modified to make clear that these variations are not
covered. In fact this is not a change of scope, but a clarification of the scope;
4) this document does not cover all the requirements for appliances above 1 000 kW. In fact
this is not a change of scope, but a clarification of the scope;
5) this document does not cover all the requirements for appliances having a supplementary
heater. In fact this is not a change of scope, but a clarification of the scope as these
appliances were never included in the past, however due to the Ecodesign Regulation it has
become necessary to mention this more explicitly;
II) Additional changes, not resulting from the revision of EN 15502-1 into EN 15502-1:2021
a) technical changes related to eco-design and energy labelling for appliances ≤ 400 kW:
1) no changes;
b) new or generally reworded requirements:
1) separation between requirements and test methods in to different clauses;
2) changes resulting from moving additional common parts from EN 15502-2-
1:2012+A1:2016 and/or EN 15502-2-2:2014 to EN 15502-1:2021 (for example all
definitions used in the parts 2 are moved to part 1; Therefore, most of the definitions in
this part are now by reference to part 1);
3) the definitions for Instructions for installation, Instructions for use and servicing, and
Technical documentation are now consequently applied throughout the document;
4) an annex Z referring to the GAR has been inserted;
5) only "instructions for installation" and "instructions for use and servicing" are defined.
Therefore, these are the only instructions to be used in this standard;
c) corrected mistakes:
1
As impacted by EN 297:1994/A2:1996, EN 297:1994/A2:1996/AC:2006, EN 297:1994/A3:1996, EN 297:1994/A4:2004, EN
297:1994/A5:1998 and EN 297:1994/A6:2003.
6
---------------------- Page: 8 ----------------------
oSIST prEN 15502-2-2:2022
prEN 15502-2-2:2022 (E)
9.2, 9.3 and the relevant subclauses of prEN 15502-2-2:2022 correct two errors present in the
EN 15502-2-2:2014 where:
9.2.1 Requirements specifies: Shall be according to EN 15502-1:2012, 9.2.1 but these efficiency
requirements are not applicable to boiler < 400 kW.
9.3 Useful efficiency at part load specifies: EN 15502-1:2012, 9.3 is not applicable but in clause
9.3 there are the following subclauses:
- 9.3.1 Requirements that are not applicable to boilers < 400 kW
- 9.3.2 Tests that are applicable to boilers having any heat input value
d) limitation of the scope compared to the standards superseded by the EN 15502 series (that
were cited in the OJEU under the GAD):
This revision only covers the update from the EN 15502-1 and an addition of an annex Z referring to the
GAR. This revision aimed not to introduce any new technical content. As some specific requirements are
not covered in the EN 15502-2-2:2014 the scope has been modified to clarify this, stating that this
standard does not include:
1) specific requirements on surface temperatures of external parts particular to children and elderly
people where relevant to ensure that this;
2) specific requirements on appliances that are intended to burn natural gases of the second family
where hydrogen is added to the natural gas;
3) specific requirements for appliances equipped with an adaptive combustion control function.
In fact these changes are not a change of scope, but a clarification of the scope;
EN 15502 consists of the following parts under the general title “Gas-fired heating boilers":
— Part 1: General requirements and tests;
— Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal
heat input not exceeding 1 000 kW;
— Part 2-2: Specific standard for type B1 appliances.
This document (Part 2-2) is to be used in conjunction with Part 1.
Relationship between this document and EN 15502-1, Gas-fired heating boilers — Part 1: General
requirements and tests:
This document is to be used in conjunction with EN 15502-1:2021 and follows the numbering structure
of EN 15502-1:2021.
Where this document states:
— shall be according to EN 15502-1:2021 (clause number) with the following modification;
— shall be according to EN 15502-1:2021 (clause number) with the following addition;
7
---------------------- Page: 9 ----------------------
oSIST prEN 15502-2-2:2022
prEN 15502-2-2:2022 (E)
— EN 15502-1:2021 (clause number) is replaced by the following;
— EN 15502-1:2021 (clause number) is not applicable;
— the relevant text of EN 15502-1:2021 is to be adapted accordingly.
This European Standard adds clauses or subclauses to the structure of EN 15502-1:2021 which are
particular to this part 2 standard. It should be noted that these clauses and subclauses are not indicated
as an addition. Clauses, subclauses and annexes which are additional to those in EN 15502-1:2021 are
numbered starting from 101, or designated as Annex XA, XB, XC, etc.
This document has been prepared under mandates M89/6 and M066, given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements as meant in
article 3 of EU Directive 2009/142/EC, relating to appliances burning gaseous fuels and the verification
methods valid for production and measurements, as meant in article 5.2 of EU Directive 92/42/EEC,
relating to the efficiency requirements for new hot water boilers fired with liquid or gaseous fuels, with
an output of 4 – 400 kW.
This document has been prepared under the mandate M/535, given to CEN by the European
Commission and the European Free Trade Association to provide a means of conforming to:
— requirements of Commission Regulation (EC) No 813/2013 of 2 August 2013 implementing
Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign
requirements for space heaters and combination heaters;
— requirements of Commission Delegated Regulation (EC) No 811/2013 of 18 February 2013
supplementing Directive 2010/30/EC of the European Parliament and of the Council with regard to
energy labelling of space heaters, combination heaters, packages of space heater, temperature
control and solar device a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.