iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 60320-1:1999

(Main)

Appliance couplers for household and similar general purposes -- Part 1: General requirements

Appliance couplers for household and similar general purposes -- Part 1: General requirements

Applicable to two-pole appliance couplers for a.c. only, with and without earthing contact, with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A.

Gerätesteckvorrichtungen für den Hausgebrauch und ähnliche allgemeine Zwecke -- Teil 1: Allgemeine Anforderungen

Connecteurs pour usages domestiques et usages généraux analogues -- Partie 1: Prescriptions générales

Applicable aux connecteurs bipolaires pour courant alternatif seulement, avec et sans contact de terre, de tension assignée ne dépassant pas 250 V et de courant assigné ne dépassant pas 16 A.

Appliance couplers for household and similar general purposes -- Part 1: General requirements (IEC 60320-1:1994)

General Information

Status
Withdrawn
Publication Date
30-Jun-1999
Withdrawal Date
28-Feb-2003
ICS
29.120.30 - Plugs, socket-outlets, couplers
Technical Committee
EPR - Electrical accessories
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Mar-2003
Due Date
01-Mar-2003
Completion Date
01-Mar-2003
Directive
73/23/EEC - Electrical equipment designed for use within certain voltage limits
Ref Project
EN 60320-1:1996 - Appliance couplers for household and similar general purposes - Part 1: General requirements

Relations

Amended By
SIST EN 60320-1:1999/A1:1999 - Appliance couplers for household and similar general purposes -- Part 1: General requirements
Effective Date
21-Sep-2010
Replaced By
SIST EN 60320-1:2003 - Appliance couplers for household and similar general purposes -- Part 1: General requirements
Effective Date
29-Jan-2023
Amended By
SIST EN 60320-1:1999/A2:1999 - Appliance couplers for household and similar general purposes -- Part 1: General requirements
Effective Date
21-Sep-2010
Replaced By
SIST EN 60320-1:2003 - Appliance couplers for household and similar general purposes -- Part 1: General requirements
Effective Date
06-May-2014
Amended By
SIST EN 60320-1:1999/A1:1999 - Appliance couplers for household and similar general purposes -- Part 1: General requirements
Effective Date
29-Jan-2023
Amended By
SIST EN 60320-1:1999/A2:1999 - Appliance couplers for household and similar general purposes -- Part 1: General requirements
Effective Date
28-Jan-2023
Amended By
SIST EN 60320-1:1999/A2:1999 - Appliance couplers for household and similar general purposes -- Part 1: General requirements
Effective Date
07-Jun-2022
Amended By
SIST EN 60320-1:1999/A1:1999 - Appliance couplers for household and similar general purposes -- Part 1: General requirements
Effective Date
07-Jun-2022
Replaced By
SIST EN 60320-1:2003 - Appliance couplers for household and similar general purposes -- Part 1: General requirements
Effective Date
07-Jun-2022
Replaces
SIST EN 60320-1:1996 - Appliance couplers for household and similar general purposes
Effective Date
06-May-2014
Replaces
SIST EN 60320-1:1996 - Appliance couplers for household and similar general purposes
Effective Date
29-Jan-2023
Replaces
SIST EN 60320-1:1996 - Appliance couplers for household and similar general purposes
Effective Date
07-Jun-2022

Buy Standard

EN 60320-1:1999EN 60320-1:1999
PreviousNext
Standard
EN 60320-1:1999
English language
125 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60320-1:1999
01-julij-1999
Appliance couplers for household and similar general purposes -- Part 1: General
requirements (IEC 60320-1:1994)
Appliance couplers for household and similar general purposes -- Part 1: General
requirements
Gerätesteckvorrichtungen für den Hausgebrauch und ähnliche allgemeine Zwecke -- Teil
1: Allgemeine Anforderungen
Connecteurs pour usages domestiques et usages généraux analogues -- Partie 1:
Prescriptions générales
Ta slovenski standard je istoveten z: EN 60320-1:1996
ICS:
29.120.30 9WLþLYWLþQLFHVSRMNH Plugs, socket-outlets,
couplers
SIST EN 60320-1:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 2 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 3 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 4 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 5 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 6 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 7 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 8 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 9 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 10 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 11 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 12 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 13 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 14 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 15 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 16 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 17 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 18 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 19 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 20 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 21 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 22 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 23 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 24 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 25 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 26 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 27 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 28 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 29 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 30 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 31 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 32 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 33 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 34 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 35 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 36 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 37 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 38 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 39 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 40 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 41 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 42 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 43 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 44 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 45 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 46 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 47 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 48 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 49 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 50 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 51 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 52 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 53 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 54 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 55 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 56 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 57 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 58 ----------------------

SIST EN 60320-1:1999

---------------------- Page: 59 ----------------------

SIST EN 60320-1:1999

----
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 60309-1:2022/AC:2023(Corrigendum)
Plugs, fixed or portable socket-outlets and appliance inlets for industrial purposes - Part 1: General requirements (IEC 60309-1:2021/COR1:2023)
EN IEC 60309-1:2022/AC:2023-06
  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62196-3:2023(Main)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility requirements for DC and AC/DC pin and contact-tube vehicle couplers (IEC 62196-3:2022)
EN IEC 62196-3:2022

This part of IEC 62196 is applicable to vehicle couplers with pins and contact tubes of standardized configuration, herein also referred to as "accessories", intended for use in electric vehicle conductive charging systems which incorporate control means, with rated operating voltage and current in accordance with IEC 62196-1:2022.
This document applies to high power DC interfaces and combined AC/DC interfaces of vehicle couplers that are intended for use in conductive charging systems for circuits specified in IEC 61851-1:2017 and IEC 6185123:-2.
The DC vehicle connectors and inlets covered by this document are used only in charging mode 4, according to IEC 618511:2017, 6.2.4, and case C, as shown in IEC 618511:2017, Figure 3.
These vehicle couplers are intended to be used for circuits specified in IEC 61851-23: - which operate at different voltages, and which can include ELV and communication signals.
This document applies to the vehicle couplers to be used in an ambient temperature between -30 °C and +40 °C.
NOTE 1 In some countries, other requirements may apply.
NOTE 2 In the following country, −35 °C applies: SE.
These vehicle couplers are intended to be connected only to cables with copper or copper-alloy conductors.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60320-3:2015/A2:2023(Amendment)
Appliance couplers for household and similar general purposes - Part 3: Standard sheets and gauges (IEC 60320-3:2014/AMD2:2022)
EN 60320-3:2014/A2:2022
  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62196-2:2023(Main)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories (IEC 62196-2:2022)
EN IEC 62196-2:2022

This part of IEC 62196 applies to EV plugs, EV socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. These accessories have a nominal rated operating voltage not exceeding 480 V AC, 50 Hz to 60 Hz, and a rated current not exceeding 63 A three phase or 70 A single phase, for use in conductive charging of electric vehicles.
This document covers the basic interface accessories for vehicle supply as specified in IEC 62196-1.
NOTE 1 The term "Electric road vehicles (EV)" comprises all road vehicles, including plug-in hybrid road vehicles (PHEV) that derive all or part of their energy from the rechargeable energy storage systems (RESS).
These accessories are intended to be used for circuits specified in IEC 61851-1:2017, which operate at different voltages and frequencies, and which can include extra-low voltage (ELV) and communication signals.
The use of these accessories for bidirectional power transfer is under consideration.
This document applies to accessories to be used in an ambient temperature between -30 °C and +40 °C.
NOTE 2 In the following country, other requirements regarding the lower temperature may apply: NO.
NOTE 3 In the following country, −35 °C applies: SE.
These accessories are intended to be connected only to cables with copper or copper-alloy conductors.
Vehicle inlets and vehicle connectors described in this document are intended to be used for charging in modes 1, 2 and 3, cases B and C. The EV socket-outlets and EV plugs covered by this document are intended to be used for charging mode 3 only, case A and B.
The modes and permissible connections are specified in IEC 61851-1:2017.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62196-1:2023(Main)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements (IEC 62196-1:2022)
EN IEC 62196-1:2022

This part of IEC 62196 is applicable to EV plugs, EV socket-outlets, vehicle connectors, vehicle inlets, herein referred to as "accessories", and to cable assemblies for electric vehicles (EV) intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding:
- 690 V AC 50 Hz to 60 Hz, at a rated current not exceeding 250 A;
- 1 500 V DC at a rated current not exceeding 800 A.
These accessories and cable assemblies are intended to be installed by instructed persons (IEV 195-04-02) or skilled persons (IEV 195-04-01) only.
These accessories and cable assemblies are intended to be used for circuits specified in IEC 61851 (all parts), which operate at different voltages and frequencies, and which can include extra-low voltage and communication signals.
These accessories and cable assemblies are intended to be used at an ambient temperature between −30 °C and +40 °C.
NOTE 1 In some countries, other requirements can apply.
NOTE 2 In the following country, −35 °C applies: SE.
NOTE 3 The manufacturer can enlarge the temperature range on the condition that the specified range information is provided.
These accessories are intended to be connected only to cables with copper or copper-alloy conductors.
The accessories covered by this document are intended for use in electric vehicle supply equipment in accordance with IEC 61851 (all parts).
This document does not apply to standard plug and socket-outlets used for mode 1 and mode 2 according to IEC 61851-1:2017, 6.2.
NOTE 4 In the following countries, mode 1 is not allowed: UK, US, CA, SG.

  • Standard
    101 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62196-6:2023(Main)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 6: Dimensional compatibility requirements for DC pin and contact-tube vehicle couplers intended to be used for DC EV supply equipment where protection relies on electrical separation (IEC 62196-6:2022)
EN IEC 62196-6:2022

IEC 62196-6:2022 is applicable to vehicle connectors, vehicle inlets and cable assemblies for electric vehicle (EV), intended for use in conductive charging systems which incorporate control means, with a rated operating voltage up to 120 V DC and rated current up to 100 A.
These accessories are intended to be used for a DC interface of the conductive charging system according to IEC 61851-25:2020.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60309-4:2022(Main)
Plugs, fixed or portable socket-outlets and appliance inlets for industrial purposes - Part 4: Switched socket-outlets with or without interlock (IEC 60309-4:2021)
EN IEC 60309-4:2022

Clause 1 of IEC 60309-1:2021 or of IEC 60309-2:2021 applies as follows:
Replace the first two paragraphs by the following:
This part of IEC 60309 applies to self-contained products primarily intended for industrial use,
either indoors or outdoors that combine the following items within a single enclosure:
– a fixed or portable socket-outlet according to IEC 60309-1 or IEC 60309-2 with a rated
operating voltage not exceeding 1 000 V DC or 1 000 V AC with a frequency not
exceeding 500 Hz and a rated current not exceeding 800 A;
– a switching device.
These products can incorporate an interlock and/or protective devices.
These accessories are intended to be installed by instructed persons or skilled persons only.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60309-2:2022(Main)
Plugs, fixed or portable socket-outlets and appliance inlets for industrial purposes - Part 2: Dimensional compatibility requirements for pin and contact-tube accessories (IEC 60309-2:2021)
EN IEC 60309-2:2022

This document applies to plugs, fixed or portable socket-outlets, and appliance inlets,
hereinafter referred to as accessories, with a rated operating voltage not exceeding 1 000 V DC
or 1 000 V AC with a frequency not exceeding 500 Hz and a rated current not exceeding 125 A,
primarily intended for industrial use, either indoors or outdoors.
These accessories are intended to be installed by instructed persons or skilled persons only.
NOTE 1 All references for accessories with a rated current of more than 125 A in IEC 60309-1 are not applicable
to this document.
This document applies to accessories with pins and contact-tubes of standardized
configurations.
This document applies to accessories, for use when the ambient temperature is normally within
the range −25 °C to 40 °C.
The use of these accessories on building sites and for agricultural, commercial and domestic
applications is not precluded.
This document applies to accessories with screwless-type terminals or insulation piercing
terminals, with a rated current up to and including 32 A for series I and 30 A for series II.
Socket-outlets or appliance inlets incorporated in or fixed to electrical equipment are within the
scope of this document. This document also applies to accessories intended to be used in
extra-low voltage installations.
NOTE 2 This document does not apply to accessories primarily intended for domestic and similar general purposes.
In locations where special conditions prevail, for example on board ship or where explosions
are liable to occur, additional requirements can be necessary.

  • Standard
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    72 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60309-1:2022(Main)
Plugs, fixed or portable socket-outlets and appliance inlets for industrial purposes - Part 1: General requirements (IEC 60309-1:2021)
EN IEC 60309-1:2022

This document applies to plugs, fixed or portable socket-outlets and appliance inlets hereinafter
referred to as accessories, with a rated operating voltage not exceeding 1 000 V DC or
1 000 V AC with a frequency not exceeding 500 Hz and a rated current not exceeding 800 A,
primarily intended for industrial use, either indoors or outdoors.
These accessories are intended to be installed by instructed persons or skilled persons only.
The list of preferred ratings is not intended to exclude other ratings.
This document applies to accessories for use when the ambient temperature is normally within
the range of −25 °C to +40 °C.
These accessories are intended to be connected to cables of copper or copper alloy only.
This document applies to accessories with screwless-type terminals or insulation piercing
terminals, with a rated current up to and including 32 A for series I and 30 A for series II.
The use of these accessories on building sites and for agricultural, commercial and domestic
applications is not precluded.
Fixed socket-outlets or appliance inlets incorporated in or fixed to electrical equipment are
within the scope of this document. This document also applies to accessories intended to be
used in extra-low voltage installations.
This document does not apply to accessories primarily intended for domestic and similar
general purposes.
This document does not cover single-pole accessories.
In locations where special conditions prevail, for example on board ship or where explosions
are liable to occur, additional requirements can be necessary.

  • Standard
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    91 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60320-1:2022(Main)
Appliance couplers for household and similar general purposes - Part 1: General requirements (IEC 60320-1:2021)
EN IEC 60320-1:2021

This part of lEC 60320 sets the general requirements for appliance couplers for two poles and
two poles with earth contact and for the connection of electrical devices for household and
similar onto the mains supply.
This document is also valid for appliance inlets/appliance outlets integrated or incorporated in
appliances.
The rated voltage does not exceed 250 V (AC) and the rated current does not exceed 16 A.
Appliance couplers complying with this document are suitable for normal use at ambient
temperatures not normally exceeding +40 °C, but their average over a period of 24 h does not
exceed +35 °C, with a lower limit of the ambient air temperature of −5 °C.
Annex E provides test requirements for derating the operating current of an accessory when
used in ambient temperatures above +35 °C up to and including +90 °C.
Appliance couplers are not suitable for:
– use in place of plug and socket-outlet systems according to IEC 60884-1;
– use in place of devices for connecting luminaires (DCLs) according to IEC 61995 or
luminaire supporting couplers (LSCs);
– use in place of installation couplers according to IEC 61535.

  • Standard
    74 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day