SIST EN 13880-2:2004

Hot applied joint sealants - Part 2: Test method for the determination of cone penetration at 25°C

This European Standard describes a method for determining the cone penetration of hot applied joint sealants using a standard penetrometer fitted with a suitable penetration cone. The initial and fuel immersed penetration values are recorded using this test method as required in prEN 14188-1.

Heiß verarbeitbare Fugenmassen - Teil 2: Prüfverfahren zur Bestimmung der Konus-Penetration bei 25°C

Diese Europäische Norm beschreibt ein Verfahren zur Bestimmung der Konus-Penetration von heiß verarbeit-baren Fugenmassen unter Anwendung eines genormten Penetrometers, das mit einem geeigneten Penetra-tionskonus ausgerüstet ist. Mit dem nach prEN 14188-1 geforderten Prüfverfahren werden die Konus-Pene-trationswerte von heiß verarbeitbaren Fugenmassen im Anlieferungszustand und nach Lagerung in Treibstoff bestimmt.

Produits de scellement de joints appliqués a chaud - Partie 2: Méthode d'essai pour la détermination de la pénétration au cône a 25°C

Cette Norme européenne décrit une méthode de détermination de la pénétration au cône des produits de scellement de joints appliqués a chaud en utilisant un pénétrometre normalisé muni d'un cône de pénétration adapté. Les valeurs de pénétrabilité initiale et apres immersion dans un hydrocarbure, sont obtenues a l'aide de la présente méthode d'essai, conformément aux exigences du prEN 14188-1.

Toplo nanosljive tesnilne mase za stike – 2. del: Preskusna metoda za ugotavljanje penetracije (s stožcem) pri 25 °C

General Information

• Status: Published
• Publication Date: 31-May-2004
• ICS: 91.100.50 - Binders. Sealing materials
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CES - Roads
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jun-2004
• Due Date: 01-Jun-2004
• Completion Date: 01-Jun-2004
• Directive: 89/106/EEC - Construction products
• Mandate: M/124 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on road construction products
• Ref Project: EN 13880-2:2003 - Hot applied joint sealants - Part 2: Test method for the determination of cone penetration at 25°C

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Toplo nanosljive tesnilne mase za stike – 2. del: Preskusna metoda za ugotavljanje penetracije (s stožcem) pri 25 °CHeiß verarbeitbare Fugenmassen - Teil 2: Prüfverfahren zur Bestimmung der Konus-Penetration bei 25°CProduits de scellement de joints appliqués a chaud - Partie 2: Méthode d'essai pour la détermination de la pénétration au cône a 25°CHot applied joint sealants - Part 2: Test method for the determination of cone penetration at 25°C93.080.20Materiali za gradnjo cestRoad construction materials91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 13880-2:2003SIST EN 13880-2:2004en01-junij-2004SIST EN 13880-2:2004SLOVENSKI
STANDARD



SIST EN 13880-2:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13880-2August 2003ICS 93.080.20English versionHot applied joint sealants - Part 2: Test method for thedetermination of cone penetration at 25°CProduits de scellement de joints appliqués à chaud - Partie2: Méthode d'essai pour la détermination de la pénétrationau cône à 25°CHeiß verarbeitbare Fugenmassen - Teil 2: Prüfverfahrenzur Bestimmung der Konus-Penetration bei 25°CThis European Standard was approved by CEN on 2 May 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13880-2:2003 ESIST EN 13880-2:2004



EN 13880-2:2003 (E)2ContentspageForeword.31Scope.42Normative references.43Terms and definitions.44Principle.45Apparatus.45.1Penetrometer.45.2Penetration cone.45.3Water bath.55.4Transfer dish.65.5Metal containers.66Preparation and conditioning of test specimens.67Test conditions.68Procedure.69Expression of results.710Precision.711Test report.7Annex A (informative)
Determination of the penetration after fuel immersion.8A.1Principle.8A.2Apparatus.8A.3Preparation and conditioning of test specimens.8A.4Procedure.8SIST EN 13880-2:2004



EN 13880-2:2003 (E)3ForewordThis document EN 13880-2:2003 has been prepared by Technical Committee CEN/TC 227 “Road materials”, thesecretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by February 2004, and conflicting national standards shall be withdrawn at the latestby March 2005.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.This European Standard is one of a series of standards as listed below:EN 13880-1, Hot applied joint sealants — Part 1: Test method for the determination of density at 25 °C.EN 13880-2, Hot applied joint sealants — Part 2: Test method for the determination of cone penetration at 25 °C.EN 13880-3, Hot applied joint sealants — Part 3: Test method for the determination of penetration and recovery(resilience).EN 13880-4, Hot applied joint selants — Part 4: Test method for the determination of heat resistance — Change inpenetration value.EN 13880-5, Hot applied joint sealants — Part 5: Test method for the determination of flow resistance.prEN 13880-6, Hot applied joint sealants — Part 6: Test method for the preparation of samples for testing.EN 13880-7, Hot applied joint sealants — Part 7: Function testing of joint sealants.EN 13880-8, Hot applied joint sealants — Part 8: Test method for the determination of the change in weight of fuelresistance joint sealants after fuel immersion.EN 13880-9, Hot applied joint sealants — Part 9: Test method for the determination of compatibility with asphaltpavements.EN 13880-10, Hot applied joint sealants — Part 10: Test method for the determination of adhesion and cohesionfollowing continuous extension and compression.EN 13880-11, Hot applied joint sealants — Part 11: Test method for the preparation of asphalt test blocks used inthe function test and for the determination of compatibility with asphalt pavements.EN 13880-12, Hot applied joint sealants — Part 12: Test method for the manufacture of concrete test blocks forbond testing (recipe methods).EN 13880-13, Hot applied joint sealants — Part 13: Test method for the determination of the discontinuousextension (adherence test).Annexe A is informative.SIST EN 13880-2:2004



EN 13880-2:2003
...