SIST EN 12697-20:2004
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or Marshall specimens
Bituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or Marshall specimens
The indentation test serves to determine the depth of indentation, and thus to test the behaviour of mastic asphalt, rolled and other such asphalts, when force is applied to them via a cylindrical indentor pin with a circular flat-ended base. Mastic asphalt as described in prEN ((WI 00227009)-6) for road construction, in prEN ((CEN/TC 303WICCCC)-2) for floor screeds and in prEN (WI 31407) for waterproofing in building and engineering constructions can be tested following the test method prescribed hereafter. The maximum nominal size of the aggregates in the mix is up to and including 16 mm.
Asphalt - Prüfverfahren für Heißasphalt - Teil 20: Eindringversuch an Würfeln oder Marshall-Probekörpern
Der Eindringversuch dient zur Bestimmung der Eindringtiefe und damit zur Prüfung des Verhaltens von Gußasphalt, Walzasphalt und ähnlichen Asphalten bei Beanspruchung mit einem zylindrischen Stempel mit kreisförmiger ebener Grund- fläche. Gußasphalt nach prEN (WI 00227009)-6 für den Straßenbau, nach prEN ((CEN/TC 303WICCCC)-2) für Estriche und nach prEN (WI 31407) für Abdichtungen im Hoch- und Tiefbau können mit dem im folgenden beschriebenen Verfahren geprüft werden. Die maximale Nenngröße der Gesteinskörnungen in dem Gemisch beträgt maximal 16 mm.
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 20: Essai d'indentation sur cubes ou éprouvettes Marshall
La présente Norme européenne décrit une méthode de mesure de l'indentation d'un asphalte coulé et d'un enrobé compacté, lorsqu'il est soumis a une force par l'intermédiaire d'un poinçon cylindrique avec un embout plat circulaire. Cette Norme européenne s'applique a des granulats dont la dimension nominale maximale est inférieure ou égale a 16 mm.
Bitumenske zmesi – Preskusne metode za vroče asfaltne zmesi – 20. del: Preskus z vtiskanjem na kocko ali preskušanec po Marshallu
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Asphalt - Prüfverfahren für Heißasphalt - Teil 20: Eindringversuch an Würfeln oder Marshall-ProbekörpernMélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 20: Essai d'indentation sur cubes ou éprouvettes MarshallBituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or Marshall specimens93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 12697-20:2003SIST EN 12697-20:2004en01-junij-2004SIST EN 12697-20:2004SLOVENSKI
STANDARD
SIST EN 12697-20:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12697-20December 2003ICS 93.080.20English versionBituminous mixtures - Test methods for hot mix asphalt - Part20: Indentation using cube or Marshall specimensMélanges bitumineux - Méthodes d'essai pour mélangehydrocarboné à chaud - Partie 20: Essai d'indentation surcubes ou sur éprouvettes MarshallAsphalt - Prüfverfahren für Heißasphalt - Teil 20:Eindringversuch an Würfeln oder Marshall-ProbekörpernThis European Standard was approved by CEN on 3 November 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12697-20:2003 ESIST EN 12697-20:2004
EN 12697-20:2003 (E)2ContentspageForeword.31Scope.52Normative references.53Apparatus.53.1Moulding of test cubes of mastic asphalt.53.2Indentation test apparatus.64Specimens.125Procedure.125.1Checking.125.2Test conditions.125.3Mixture specimens for the test cube moulding.125.4Moulding of test cubes.125.5Preparation and conditioning of the specimens.135.6Application of the force.136Result.147Precision.148Test report.14SIST EN 12697-20:2004
EN 12697-20:2003 (E)3ForewordThis document (EN 12697-20:2003) has been prepared by Technical Committee CEN/TC 227 “Roadmaterials”, the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by June 2004, and conflicting national standards shall be withdrawn atthe latest by August 2005.This European Standard is one of a series of standards as listed below:EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content.EN 12697-2, Bituminous mixtures — Test methods for hot mix asphalt — Part 2: Determination of particle sizedistribution.EN 12697-3, Bituminous mixtures — Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotaryevaporator.EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bitumen recovery:Fractionating column.EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of themaximum density.EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk densityof bituminous specimens.EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk densityof bituminous specimens by gamma rays.EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of voidcharacteristics of bituminous specimens.EN 12697-9, Bituminous mixtures — Test methods for hot mix asphalt — Part 9: Determination of thereference density.EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactibility.EN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of theaffinity between aggregate and bitumen.EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the watersensitivity of bituminous
specimensEN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperaturemeasurement.EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content.EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of thesegregation sensitivity.prEN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studdedtyres.SIST EN 12697-20:2004
EN 12697-20:2003 (E)4prEN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Partial loss of porousasphalt specimen.prEN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage fromporous asphalt.prEN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability ofspecimen.EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube orMarshall specimen.prEN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using platespecimens.prEN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking.EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of theindirect tensile strength of bituminous specimens.prEN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue.prEN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25: Cyclic compression test.prEN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness.EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling.EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples fordetermining binder content, water content and grading.EN 12697-29, Bituminous mixtures — Test methods for hot mix asphalt — Part 29: Determination of thedimensions of bituminous specimen.prEN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation,impact compactor.prEN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparationgyratory compactor.prEN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compactionof bituminous mixtures by vibratory compactor.EN 12697-33, Bituminous mixtures — Test methods for hot mix asphalt — Part 33: Specimen prepared byroller compactor.prEN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test.prEN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing.EN 12697-36, Bituminous mixtures — Test methods for hot mix asphalt — Part 36: Determination of thethickness of a bituminous pavement.EN 12697-37, Bituminous mixtures — Test methods for hot mix asphalt — Part 37: Hot sand test for theadhesivity of binder on precoated chippings for HRA.prEN 12697-38, Bituminous mixtures — Test methods for hot mix asphalt — Part 38: Test equipment andcalibration.SIST EN 12697-20:2004
EN 12697-20:2003 (E)5prEN 12697-39, Bituminous mixtures — Test methods for hot mix asphalt — Part 39: Binder content byignition.prEN 12697-41, Bituminous mixtures — Test methods for hot mix asphalt — Part 41: Resistance to de-icingfluids.prEN 12697-42, Bituminous mixtures — Test methods for hot mix asphalt — Part 42: Amount of foreignmatters in reclaimed asphalt.prEN 12697-43, Bituminous mixtures — Test methods for hot mix asphalt — Part 43: Resistance to fuel.prEN 12697-45, Bituminous mixtures — Test methods for hot mix asphalt — Part 45: Binder drainage –Schellenberg methodNo existing European Standard is superseded.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom.1 ScopeThis European Standard describes a test method for determining the depth of indentation of mastic asphaltand rolled asphalt, when force is applied to them via a cylindrical indentor pin with a circular flat-ended base.This European Standard applies to aggregates of maximum nominal size less or equal to 16 mm.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications.These normative references are cited at the appropriate places in the text, and the publications are listedhereafter. For dated references, subsequent amendments to or revisions of any of these publications apply tothis European Standard only when incorporated in it by amendment or revision. For undated references thelatest edition of the publication referred to applies (including amendments).EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling.prEN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation,impact compactor.EN 12970, Mastic asphalt for waterproofing — Definitions, requirements and test methods.prEN 13108-6, Bituminous mixtures — Material sp
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.