SIST EN ISO 6185-3:2018
(Main)Inflatable boats - Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater (ISO 6185-3:2014)
Inflatable boats - Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater (ISO 6185-3:2014)
This part of ISO 6185 specifies the minimum safety characteristics required for the design, materials
to use, manufacture and testing of inflatable boats and rigid inflatable boats with a hull length LH in
accordance with ISO 8666 less than 8 m with a motor power rating of 15 kW and greater.
This part of ISO 6185 is applicable to the following types of boats intended for use within the operating
temperatures of – 20 °C to + 60 °C:
— Type VII: Powered Boats fitted with a buoyancy tube attached to the port and starboard sides,
suitable for navigation in conditions of Design Categories C and D and capable of installing motor
power rating of 15 kW and greater.
— Type VIII: Powered Boats fitted with a buoyancy tube attached to the port and starboard sides,
suitable for navigation in conditions of Design Category B capable of installing motor power rating
of 75kW and greater.
NOTE 1 General arrangements of typical boats of Types VII and VIII are given in Annexes A and B, respectively.
This part of ISO 6185 excludes single-chambered boats and boats made from unsupported materials,
and is not applicable to aquatic toys and inflatable liferafts.
NOTE 2 For craft, concerned by the Recreational Craft Directive (RCD) of the European Union, fitted with
inboard engines with nonstandard integral exhausts, noise emission requirements need to be considered.
Aufblasbare Boote - Teil 3: Boote mit einer Rumpflänge unter 8 m mit einer Motorleistung von mindestens 15 kW (ISO 6185-3:2014)
Bateaux pneumatiques - Partie 3: Bateaux d'une longueur de coque inférieure à 8 m et d'une puissance moteur assignée supérieure ou égale à 15 kW (ISO 6185-3:2014)
L'ISO 6185-3:2014 spécifie les caractéristiques minimales de sécurité requises concernant la conception, les matériaux à utiliser, la fabrication et les essais des bateaux pneumatiques et semi-rigides d'une longueur de coque, mesurée conformément à l'ISO 8666, inférieure à 8 m et dont la puissance moteur assignée est supérieure ou égale à 15 kW.
L'ISO 6185-3:2014 s'applique aux types de bateaux suivants destinés à être utilisés dans une plage de températures d'utilisation comprise entre -20 °C et +60 °C:
Type VII: Bateaux à moteur (d'une puissance ≥15 kW) équipés de chambres de flottabilité reliées aux cotés bâbord et tribord, appropriés à une navigation en catégories de conception C et D et sur lesquels on peut installer des moteurs d'une puissance assignée supérieure ou égale à 15 kW.
Type VIII: Bateaux à moteur (d'une puissance ≥75 kW) équipés de chambres de flottabilité reliées aux cotés bâbord et tribord, appropriés à une navigation en catégories de conception B et sur lesquels on peut installer des moteurs d'une puissance assignée supérieure ou égale à 75 kW.
L'ISO 6185-3:2014 exclut les bateaux à flotteur monochambre, et les bateaux en matériaux non renforcés, et ne s'applique ni aux jouets aquatiques ni aux radeaux de survie gonflables.
Napihljivi čolni - 3. del: Čolni s trupom, krajšim od 8 m, in motorjem z močjo, večjo ali enako 15 kW (ISO 6185-3:2014)
Ta del standarda ISO 6185 določa minimalne varnostne lastnosti, zahtevane za načrtovanje, materiale za uporabo, izdelavo in preskušanje napihljivih čolnov ter napihljivih čolnov, ki imajo v spodnjem delu trupa togo enoto, z dolžino trupa (LH) manj kot 8 m (v skladu s standardom ISO 8666) in motorjem z močjo najmanj 15 kW.
Ta del standarda ISO 6185 se uporablja za naslednje tipe čolnov, namenjenih za uporabo pri delovnih temperaturah od –20 °C do 60 °C:
– tip VII: čolni na motorni pogon s plovno cevjo, pritrjeno na desno in levo stran, ki so primerni za krmarjenje v razmerah konstrukcijskih kategorij C in D z možnostjo namestitve motorja z močjo, večjo ali enako 15 kW;
– tip VIII: čolni na motorni pogon s plovno cevjo, pritrjeno na desno in levo stran, ki so primerni za krmarjenje v razmerah konstrukcijske kategorije B z možnostjo namestitve motorja z močjo, večjo ali enako 75kW.
OPOMBA 1: Splošne razvrstitve običajnih čolnov tipa VII in VIII so podane v ustreznih dodatkih A in B.
Ta del standarda ISO 6185 ne zajema enokabinskih čolnov in čolnov, izdelanih iz nepodprtih materialov ter se ne uporablja za vodne igrače in napihljive rešilne splave.
OPOMBA 2: Za plovila, ki so zajeta v direktivi o rekreacijskih plovilih (RCD) Evropske unije in opremljena z notranjim motorjem z nestandardnim vgrajenim izpušnim sistemom, je treba upoštevati zahteve glede emisij hrupa.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 6185-3:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 6185-3:2014
1DSLKOMLYLþROQLGHO ýROQLVWUXSRPNUDMãLPRGPLQPRWRUMHP]PRþMRYHþMR
DOLHQDNRN: ,62
Inflatable boats - Part 3: Boats with a hull length less than 8 m with a motor rating of 15
kW and greater (ISO 6185-3:2014)
Aufblasbare Boote - Teil 3: Boote mit einer Rumpflänge unter 8 m mit einer Motorleistung
von mindestens 15 kW (ISO 6185-3:2014)
Bateaux pneumatiques - Partie 3: Bateaux d'une longueur de coque inférieure à 8 m et
d'une puissance moteur assignée supérieure ou égale à 15 kW (ISO 6185-3:2014)
Ta slovenski standard je istoveten z: EN ISO 6185-3:2018
ICS:
47.080 ýROQL Small craft
SIST EN ISO 6185-3:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6185-3:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 6185-3:2018
EN ISO 6185-3
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 6185-3:2014
English Version
Inflatable boats - Part 3: Boats with a hull length less than
8 m with a motor rating of 15 kW and greater (ISO 6185-
3:2014)
Bateaux pneumatiques - Partie 3: Bateaux d'une Aufblasbare Boote - Teil 3: Boote mit einer Rumpflänge
longueur de coque inférieure à 8 m et d'une puissance unter 8 m mit einer Motorleistung von mindestens 15
moteur assignée supérieure ou égale à 15 kW (ISO kW (ISO 6185-3:2014)
6185-3:2014)
This European Standard was approved by CEN on 16 April 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6185-3:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 6185-3:2018
EN ISO 6185-3:2018 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 6185-3:2018
EN ISO 6185-3:2018 (E)
European foreword
The text of ISO 6185-3:2014 has been prepared by Technical Committee ISO/TC 188 “Small craft” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 6185-3:2018.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall be
withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6185-3:2014.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2013/53/EU.
For relationship with EU Directive 2013/53/EU, see informative Annex ZA, which is an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Forme
...
SLOVENSKI STANDARD
oSIST prEN ISO 6185-3:2018
01-februar-2018
1DSLKOMLYLþROQLGHO ýROQLVWUXSRPNUDMãLPRGPLQPRWRUMHP]PRþMRYHþMR
DOLHQDNRN: ,62
Inflatable boats - Part 3: Boats with a hull length less than 8 m with a motor rating of 15
kW and greater (ISO 6185-3:2014)
Aufblasbare Boote - Teil 3: Boote mit einer Rumpflänge unter 8 m mit einer Motorleistung
von mindestens 15 kW (ISO 6185-3:2014)
Bateaux pneumatiques - Partie 3: Bateaux d'une longueur de coque inférieure à 8 m et
d'une puissance moteur assignée supérieure ou égale à 15 kW (ISO 6185-3:2014)
Ta slovenski standard je istoveten z: prEN ISO 6185-3
ICS:
47.080 ýROQL Small craft
oSIST prEN ISO 6185-3:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 6185-3:2018
---------------------- Page: 2 ----------------------
oSIST prEN ISO 6185-3:2018
DRAFT
EUROPEAN STANDARD
prEN ISO 6185-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2017
ICS 47.080 Will supersede EN ISO 6185-3:2014
English Version
Inflatable boats - Part 3: Boats with a hull length less than
8 m with a motor rating of 15 kW and greater (ISO 6185-
3:2014)
Bateaux pneumatiques - Partie 3: Bateaux d'une Aufblasbare Boote - Teil 3: Boote mit einer Rumpflänge
longueur de coque inférieure à 8 m et d'une puissance unter 8 m mit einer Motorleistung von mindestens 15
moteur assignée supérieure ou égale à 15 kW (ISO kW (ISO 6185-3:2014)
6185-3:2014)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/SS T01.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 6185-3:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 6185-3:2018
prEN ISO 6185-3:2017 (E)
Contents
Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 6185-3:2018
prEN ISO 6185-3:2017 (E)
European foreword
The text of ISO 6185-3:2014 has been prepared by Technical Committee ISO/TC 188 “Small craft” of the
International Organization for Standardization (ISO) and has been taken over as prEN ISO 6185-3:2017.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN ISO 6185-3:2014.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2013/53/EU.
For relationship with EU Directive 2013/53/EU, see informative Annex ZA, which is an integral part of
this document.
Endorsement notice
The text of ISO 6185-3:2014 has been approved by CEN as prEN ISO 6185-3:2017 without any
modification.
3
---------------------- Page: 5 ----------------------
oSIST prEN ISO 6185-3:2018
prEN ISO 6185-3:2017 (E)
Annex ZA
(informative)
Relationship between this European Standard and the Essential
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.