SIST EN IEC 61784-5-2:2019/A1:2024
(Amendment)Industrial communication networks - Profiles - Part 5-2: Installation of fieldbuses - Installation profiles for CPF 2 (IEC 61784-5-2:2018/AMD1:2024)
Industrial communication networks - Profiles - Part 5-2: Installation of fieldbuses - Installation profiles for CPF 2 (IEC 61784-5-2:2018/AMD1:2024)
Industrielle Kommunikationsnetze - Profile - Teil 5-2: Feldbusinstallation - Installationsprofile für die Kommunikationsprofilfamilie 2 (IEC 61784-5-2:2018/AMD1:2024)
Réseaux de communication industriels - Profils - Partie 5-2 : Installation des bus de terrain - Profils d'installation pour CPF 2 (IEC 61784-5-2:2018/AMD1:2024)
Industrijska komunikacijska omrežja - Profili - 5-2. del: Inštalacija procesnih vodil - Inštalacijski profili za CPF 2 - Dopolnilo A1 (IEC 61784-5-2:2018/AMD1:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Industrijska komunikacijska omrežja - Profili - 5-2. del: Inštalacija procesnih vodil -
Inštalacijski profili za CPF 2 - Dopolnilo A1 (IEC 61784-5-2:2018/AMD1:2024)
Industrial communication networks - Profiles - Part 5-2: Installation of fieldbuses -
Installation profiles for CPF 2 (IEC 61784-5-2:2018/AMD1:2024)
Industrielle Kommunikationsnetze - Profile - Teil 5-2: Feldbusinstallation -
Installationsprofile für die Kommunikationsprofilfamilie 2 (IEC 61784-5-
2:2018/AMD1:2024)
Réseaux de communication industriels - Profils - Partie 5-2 : Installation des bus de
terrain - Profils d'installation pour CPF 2 (IEC 61784-5-2:2018/AMD1:2024)
Ta slovenski standard je istoveten z: EN IEC 61784-5-2:2018/A1:2024
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
35.100.40 Transportni sloj Transport layer
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61784-5-2:2018/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM May 2024
ICS 25.040.40; 35.100.40
English Version
Industrial communication networks - Profiles - Part 5-2:
Installation of fieldbuses - Installation profiles for CPF 2
(IEC 61784-5-2:2018/AMD1:2024)
Réseaux de communication industriels - Profils - Partie 5-2 : Industrielle Kommunikationsnetze - Profile - Teil 5-2:
Installation des bus de terrain - Profils d'installation pour Feldbusinstallation - Installationsprofile für die
CPF 2 Kommunikationsprofilfamilie 2
(IEC 61784-5-2:2018/AMD1:2024) (IEC 61784-5-2:2018/AMD1:2024)
This amendment A1 modifies the European Standard EN IEC 61784-5-2:2018; it was approved by CENELEC on 2024-04-25. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61784-5-2:2018/A1:2024 E
European foreword
The text of document 65C/1283/FDIS, future IEC 61784-5-2/AMD1, prepared by SC 65C "Industrial
networks" of IEC/TC 65 "Industrial-process measurement, control and automation" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61784-5-2:2018/A1:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-01-25
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-04-25
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61784-5-2:2018/AMD1:2024 was approved by CENELEC
as a European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Replace EN IEC 61918 with the following references:
Publication Year Title EN/HD Year
IEC 61918 2018 Industrial communication networks - EN IEC 61918 2018
Installation of communication networks in
industrial premises
- - + A11 2019
- - + A12 2023
- - + AC 2019-03
+ AMD1 2022 + A1 2022
+ AMD2 2024 + A2 2024
The normative references of EN IEC 61918:2018, EN IEC 61918:2018/A11:2019,
EN IEC 61918:2018/A12:2023, EN IEC 61918:2018/AC:2019-03, EN IEC 61918:2018/A1:2022, and
EN IEC 61918:2018/A2:2024 apply.
IEC 61784-5-2 ®
Edition 4.0 2024-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 1
AMENDEMENT 1
Industrial communication networks – Profiles –
Part 5-2: Installation of fieldbuses – Installation profiles for CPF 2
Réseaux de communication industriels – Profils –
Partie 5-2: Installation des bus de terrain – Profils d’installation pour CPF 2
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.040.40, 35.100.40 ISBN 978-2-8322-8401-8
– 2 – IEC 61784-5-2:2018/AMD1:2024
© IEC 2024
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUSTRIAL COMMUNICATION NETWORKS –
PROFILES –
Part 5-2: Installation of fieldbuses –
Installation profiles for CPF 2
AMENDMENT 1
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to IEC 61784-5-2:2018 has been prepared by subcommittee 65C: Industrial
networks, of IEC technical committee 65: Industrial-process measurement, control and
automation.
IEC 61784-5-2:2018/AMD1:2024 – 3 –
© IEC 2024
The text of this Amendment is based on the following documents:
Draft Report on voting
65C/1283/FDIS 65C/1297/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this Amendment is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications/.
A list of all parts of IEC 61784-5 series, under the general title Industrial networks – Profiles –
Installation of fieldbuses, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn, or
• revised.
IMPORTANT – The "colour inside" logo on the cover page of this document indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this document using a colour printer.
___________
INTRODUCTION to Amendment 1
This Amendment 1 includes the following significant technical changes with respect to
IEC 61784-5-2:2018:
a) Updated references of IEC 61918:2018 to include additions of IEC 61918:2018/AMD1:2022
and IEC 61918:2018/AMD2:2024,
b) Added references for consideration of security to Subclause B.4.2.2,
c) Updated optical fiber specifications and references in Subclauses B.4.3.3.2 and B.4.4.1.4,
d) Added definition of electromagnetic compatibility options for conformance to Subclause
B.4.4.1.2.1,
e) Added support of mesh bonding systems to Subclause B.4.4 and Clause B.5,
f) Added acceptance of end-to-end link verification and certification testing to Clause B.6.
– 4 – IEC 61784-5-2:2018/AMD1:2024
© IEC 2024
FOREWORD
Insert, after the first paragraph, the following new paragraph:
This document is to be used in conjunction with IEC 61918:2018, IEC 61918:2018/AMD1:2022
and IEC 61918:2018/AMD2:2024.
Delete, below the list of modifications, the following paragraph:
This standard is to be used in conjunction with IEC 61918:2018.
INTRODUCTION
Replace, at the beginning of the first paragraph, "International Standard" with "document".
Replace, at the beginning of the second paragraph, "IEC 61918:2018 provides" with
"IEC 61918:2018, IEC 61918:2018/AMD1:2022 and IEC 61918:2018/AMD2:2024 provide".
Replace the existing Figure 1 with the following new figure:
Figure 1 – Standards relationships
IEC 61784-5-2:2018/AMD1:2024 – 5 –
© IEC 2024
1 Scope
Replace the existing second paragraph with the following new paragraph:
The installation profiles are specified in the annexes. These annexes are read in conjunction
with IEC 61918:2018, IEC 61918:2018/AMD1:2022 and IEC 61918:2018/AMD2:2024.
2 Normative
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.