SIST EN ISO 4066:2002
(Main)Construction drawings - Bar scheduling (ISO 4066:1994)
Construction drawings - Bar scheduling (ISO 4066:1994)
2009-10-23 SJ: Inter-standard links were missing. Revised version was published (WI CSF01087), but this version was not withdrawn. Decision not to undertake corrective action (GM/MHT).
Zeichnungen für das Bauwesen - Stabliste (ISO 4066:1994)
Diese Internationale Norm legt ein System für die Auflistung von Bewehrungsstäben fest und umfaßt: - die Bemaßungsmethode; - ein Sclüsselsystem für Stabformen; - eine Anzahl von Vorzugs-Stabformen; - die Stabliste. Diese Internationale Norm gilt für alle Arten von Bewehrungsstäben aus Stahl. Sie gilt nicht für Stahlbau und Spannbeton.
Dessins de bâtiment et génie civil - Cahiers de ferraillage (ISO 4066:1994)
Gradbeniške risbe - Seznam armaturnih palic (ISO 4066:1994)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 4066:2002
01-februar-2002
Gradbeniške risbe - Seznam armaturnih palic (ISO 4066:1994)
Construction drawings - Bar scheduling (ISO 4066:1994)
Zeichnungen für das Bauwesen - Stabliste (ISO 4066:1994)
Dessins de bâtiment et génie civil - Cahiers de ferraillage (ISO 4066:1994)
Ta slovenski standard je istoveten z: EN ISO 4066:1999
ICS:
01.100.30 *UDGEHQLQDþUWL Construction drawings
SIST EN ISO 4066:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 2 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 3 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 4 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 5 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 6 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 7 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 8 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 9 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 10 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 11 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 12 ----------------------
SIST EN ISO 4066:2002
---------------------- Page: 13 ----------------------
SIST EN ISO 4066:2002
ISO
INTERNATIONAL
4066
STANDARD
Second edition
1994-09-01
Construction drawings - Bar scheduling
Dessins de batiment et g6nie civil - Cahiers de ferrailage
Reference number
ISO 40663 994(E)
---------------------- Page: 14 ----------------------
SIST EN ISO 4066:2002
ISO 4066: 1994(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national Standards bodies (ISO member bodies). The work
of preparing International Standards is normally carried out through ISO
technical committees. Esch member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(1 EC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 4066 was prepared by Technical Committee
ISO~C 10, Technical drawings, product definition and reiated documen-
tation, Subcommittee SC 8, Construction documentatjon.
This second edition cancels and replaces the first edition
which has been technically revised.
(ISO 4066:1977),
0 ISO 1994
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronie or mechanical, including photocopying and
microfilm, without Permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-l 211 Geneve 20 l Switzerland
Printed in Switzerland
---------------------- Page: 15 ----------------------
SIST EN ISO 4066:2002
Introduction
The purpose of this International Standard is to ensure uniformity of prac-
tice in the scheduling of steel bars for the reinforcement of concrete. To
establish a clear and unambiguous System for scheduling, it is necessary
to specify the method of indicating dimensions to be used and the Order
in which the information is given on the bar schedule.
As the use of preferred shapes is considered to be very advantageous
both for simplifying design and manufacture and for the use of Computers,
the opportunity has been taken to include a list of preferred shapes and
a coding System; the layout of the bar schedule is based on the use of
preferred shapes.
. . .
Ill
---------------------- Page: 16 ----------------------
SIST EN ISO 4066:2002
This page intentionally left blank
---------------------- Page: 17 ----------------------
SIST EN ISO 4066:2002
ISO 4066: 1994(E)
INTERNATIONAL STANDARD 0 ISO
- Bar scheduling
Construction drawings
tolerantes; this dimension need not be shown on
1 Scope
schedules.
This International Standard establishes a System for
The total length (cutting length) shall be calculated on
the scheduling of reinforcing bars, and comprises
the basis of the appropriate bending dimensions with
corrections for bends.
- the method of indicating dimensions;
- a coding System for bar shapes;
- a list of preferred shapes;
- the bar schedule.
This International Standard applies to all types of steel
bar for the reinforcement of concrete. lt does no apply
to steel fabric and prestressing steel reinforcement.
a
2 Indication of bending dimensions
Figure 1 - Bending dimensions - Shape
The bending dimensions shall be indicated as shown
code 26
in figures 1 to 5.
Dimensions shall be outside dimensions, except for
radii, and the Standard radius of bend shall be the
smallest radius permitted by national Standards regu-
\
lations for the size of bar scheduled.
\
If a national Standard specifies different Standard radii
XI
for different situations, the radius to be used shall be
Ll
entered in the column e/R.
\ \
\
\
Except for shape Codes 12, 13, 33, 67 and 77, all
I
(e)
bends will be assumed to have Standard radii. No di- I /
mension shall be Zero.
Figur
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.