SIST EN 13599:2014
(Main)Copper and copper alloys - Copper plate, sheet and strip for electrical purposes
Copper and copper alloys - Copper plate, sheet and strip for electrical purposes
This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper plate, sheet and strip for electrical purposes with thicknesses from 0,05 mm up to and including 25 mm and widths from 10 mm up to and including 1 250 mm. The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.
Kupfer und Kupferlegierungen - Platten, Bleche und Bänder aus Kupfer für die Anwendung in der Elektrotechnik
Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften, einschließlich elektrischer Eigenschaften, Grenzabmaße und Formtoleranzen von Platten, Blechen und Bändern aus Kupfer mit Dicken von 0,05 mm bis 25 mm und Breiten von 10 mm bis 1 250 mm für die Elektrotechnik fest.
Der Ablauf der Probenentnahme und die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen dieser Europäischen Norm sind ebenfalls festgelegt.
Cuivre et alliages de cuivre - Plaques, tôles et bandes en cuivre pour usages électriques
La présente Norme européenne spécifie la composition, les caractéristiques, y compris les caractéristiques électriques et les tolérances de dimensions et de formes des plaques, tôles et bandes en cuivre pour usages électriques avec des épaisseurs comprises entre 0,05 mm et 25 mm inclus et des largeurs comprises entre 10 mm et 1 250 mm inclus.
Les procédures d'échantillonnage et les méthodes d'essai pour la vérification de la conformité aux exigences de la présente Norme européenne sont également spécifiées.
Baker in bakrove zlitine - Bakrove plošče, pločevina in trakovi za uporabo v elektrotehniki
Ta evropski standard določa sestavo, zahteve glede značilnosti, vključno z električnimi lastnostmi, in odstopanja glede dimenzij ter oblik za bakrene plošče in trakove za električno uporabo z debelino od 0,05 mm do vključno 25 mm ter širino od 10 mm do vključno 1250 mm. Določeni so tudi postopki vzorčenja in preskusne metode za preverjanje skladnosti s tem evropskim standardom.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.HOHNWURWHKQLNLKupfer und Kupferlegierungen - Platten, Bleche und Bänder aus Kupfer für die Anwendung in der ElektrotechnikCuivre et alliages de cuivre - Plaques, tôles et bandes en cuivre pour usages électriquesCopper and copper alloys - Copper plate, sheet and strip for electrical purposes77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 13599:2014SIST EN 13599:2014en,fr,de01-junij-2014SIST EN 13599:2014SLOVENSKI
STANDARDSIST EN 13599:20041DGRPHãþD
SIST EN 13599:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13599
January 2014 ICS 77.150.30 Supersedes EN 13599:2002English Version
Copper and copper alloys - Copper plate, sheet and strip for electrical purposes
Cuivre et alliages de cuivre - Plaques, tôles et bandes en cuivre pour usages électriques
Kupfer und Kupferlegierungen - Platten, Bleche und Bänder aus Kupfer für die Anwendung in der Elektrotechnik This European Standard was approved by CEN on 3 November 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13599:2014 ESIST EN 13599:2014
EN 13599:2014 (E) 2 Contents Page Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .4 4 Designations .5 4.1 Material .5 4.2 Material condition .5 4.3 Product .5 5 Ordering information .6 6 Requirements .8 6.1 Composition .8 6.2 Mechanical properties .8 6.3 Bending characteristics .8 6.4 Electrical properties .8 6.5 Freedom from hydrogen embrittlement .8 6.6 Dimensions and tolerances .9 6.7 Edgewise curvature c .9 6.8 Surface condition.9 7 Sampling .9 7.1 General .9 7.2 Analysis .9 7.3 Mechanical and electrical tests . 10 8 Test methods . 10 8.1 Analysis . 10 8.2 Tensile test . 10 8.3 Hardness test . 10 8.4 Bend test . 10 8.5 Electrical resistivity test . 11 8.6 Hydrogen embrittlement test . 11 8.7 Retests . 12 8.8 Rounding of results . 12 9 Declaration of conformity and inspection documentation . 12 9.1 Declaration of conformity . 12 9.2 Inspection documentation . 12 10 Marking, packaging, labelling . 12 Annex A (informative)
Characteristics of coppers for electrical purposes . 19 A.1 General grouping of copper types . 19 A.2 General characteristics . 19 A.3 Particular characteristics . 19 Bibliography . 21
SIST EN 13599:2014
EN 13599:2014 (E) 3 Foreword This document (EN 13599:2014) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2014, and conflicting national standards shall be withdrawn at the latest by July 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13599:2002. Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 2 “Rolled flat products” to revise the following standard: EN 13599:2002, Copper and copper alloys — Copper plate, sheet and strip for electrical purposes The products specified in this European Standard are those which are especially suitable for electrical purposes, i.e. with specified electrical properties. Copper plate, sheet and strip for general purposes are specified in EN 1652. This is one of a series of European Standards for copper products for electrical purposes. Other copper products are specified as follows: EN 13600, Copper and copper alloys — Seamless copper tubes for electrical purposes EN 13601, Copper and copper alloys — Copper rod, bar and wire for general electrical purposes EN 13602, Copper and copper alloys — Drawn, round copper wire for the manufacture of electrical conductors EN 13604, Copper and copper alloys — Products of high conductivity copper for electronic tubes, semiconductor devices and vacuum applications EN 13605, Copper and copper alloys — Copper profiles and profiled wire for electrical purposes In comparison with EN 13599:2002, the following significant changes were made: a) Table 2, Cu-FRHC, other elements – content has been modified and a new footnote “d” has been added; b) the normative references have been updated. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 13599:2014
EN 13599:2014 (E) 4 1 Scope This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper plate, sheet and strip for electrical purposes with thicknesses from 0,05 mm up to and including 25 mm and widths from 10 mm up to and including 1 250 mm. The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1655, Copper and copper alloys - Declarations of conformity EN 1976, Copper and copper alloys - Cast unwrought copper products EN 10204, Metallic products - Types of inspection documents EN ISO 2626, Copper - Hydrogen embrittlement test (ISO 2626) EN ISO 6507-1, Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1) EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1) EN ISO 7438, Metallic materials - Bend test (ISO 7438) ISO 1811-2, Copper and copper alloys — Selection and preparation of samples for chemical analysis — Part 2: Sampling of wrought products and castings 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 plate flat rolled product of rectangular cross-section with uniform thickness greater than 10 mm 3.2 sheet flat rolled product of rectangular cross-section with uniform thickness from 0,2 mm up to and including 10 mm, supplied in straight lengths, usually with sheared or sawn edges Note 1 to entry: The thickness does not exceed one tenth of the width. 3.3 strip flat rolled product of rectangular cross-section with uniform thickness from 0,05 mm up to and including 5,0 mm manufactured in coil and supplied in as sheared coils, traverse wound coils or cut to length, usually with slit edges Note 1 to entry: The thickness does not exceed one tenth of the width. SIST EN 13599:2014
EN 13599:2014 (E) 5 4 Designations 4.1 Material 4.1.1 General The material is designated either by symbol or by number (see Table 1). 4.1.2 Symbol The material symbol designation is based on the designation system given in ISO 1190-1. NOTE Although material symbol designations used in this standard might be the same as those in other standards using the designation system in ISO 1190-1, the detailed composition requirements are not necessarily the same. 4.1.3 Number The material number designation is in accordance with the system given in EN 1412. 4.2 Material condition For the purposes of this standard, the following designations, which are in accordance with the system given in EN 1173, apply for the material condition: M Material condition for the product as manufactured without specified mechanical properties; H… Material condition designated by the minimum value of hardness requirement for the product with
mandatory hardness requirements; R… Material condition designated by the minimum value of tensile strength requirement for the product
with mandatory tensile strength and elongation requirements. NOTE Some R. material conditions in this European Standard apply to products which also have mandatory 0,2 % proof strength requirements. Exact conversion between material conditions designated H. and R. is not possible. Material condition is designated by only one of the above designations. 4.3 Product The product designation provides a standardised pattern of designation from which a rapid and unequivocal description of a product can be conveyed in communication. It provides mutual comprehension at the international level with regard to products which meet the requirements of the relevant European Standard. The product designation is no substitute for the full content of the standard. The product designation for products to this European Standard shall consist of: — denomination (Plate, Sheet or Strip); — number of this European Standard (EN 13599); — material designation, either symbol or number (see Table 1); — material condition designation (see Table 2); SIST EN 13599:2014
EN 13599:2014 (E) 6 — nominal dimensions; — plate: thickness × width × length [either “as manufactured” (ML) or “fixed” (FL) length]; — sheet: thickness × width × length [either “as manufactured” (ML) or “fixed” (FL) length] (see Example 1); — strip (as sheared coils or as transverse wound coils on spools): thickness × width (see Example 2); — strip (cut to length): thickness × width × length [either “as manufactured” (ML) or “fixed” (FL) length]. The derivation of a product designation is shown in Example 1. EXAMPLE 1 Sheet for electrical purposes conforming to this European Standard, in material designated either Cu-ETP or CW004A, in material condition H040, nominal thickness 6,0 mm, nominal width 600 mm, as manufactured length 2 000 mm, will be designated as follows: Sheet EN 13599 — Cu-ETP — H040 — 6,0 × 600 × 2 000ML or Sheet EN 13599 — CW004A — H040 — 6,0 × 600 × 2 000ML Denomination Number of this European Standard Material designation Material condition designation Nominal dimension in millimetres EXAMPLE 2 Strip for electrical purposes conforming to this European Standard, in material designated either CuAg0,10 or CW013A, in material condition R290, nominal thickness 2,0 mm, nominal width 1 000 mm, will be designated as follows:
Strip EN 13599 — CuAg0,10 — R290 — 2,0 × 1 000
or
Strip EN 13599 — CW013A — R290 — 2,0 × 1 000 5 Ordering information In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser and the supplier, the purchaser shall state on his enquiry and order the following information: a) quantity of product required: 1) plate: number of pieces or mass; 2) sheet: number of pieces or mass; 3) strip (as sheared coils or as transverse wound coils on spools): mass; 4) strip (cut to length): mass or number of pieces; SIST EN 13599:2014
EN 13599:2014 (E) 7 b) denomination (Plate, Sheet or Strip); c) number of this European Standard (EN 13599); d) material designation (see 4.1 and Table 1); e) material condition designation (see 4.2 and Table 2); f) nominal dimensions: 1) plate, sheet, strip (cut to length): thickness [for thicknesses from 0,05 mm up to and including 3,2 mm and with widths from 10 mm up to and including 200 mm, thickness tolerance either “normal” (N) or “special” (S)] × width × length (either “as manufactured” or “fixed” length); 2) strip (as sheared coils or as transverse wound coils on spools): thickness [for thicknesses from 0,05 mm up to and including 3,2 mm and with widths from 10 mm up to and including 200 mm, thickness tolerance either “normal” (N) or “special” (S)] × width; g) size of sheared coils (strip) requirements: nominal inside diameter in millimetres and maximum outside diameter in millimetres and either maximum mass in kilograms or approximate specific coil mass (mass per width) in kilograms per millimetre; h) size of traverse wound coils (strip): type or dimensions. It is recommended that the product designation, as described in 4.3, is used for items b) to f). In addition, the purchaser shall also state on the enquiry and order any of the following, if required: i) maximum edgewise curvature values for strip over 3,2 mm up to and including 5,0 mm thickness and width over 30 mm (see Table 9); j) whether special surface conditions are required (see 6.8); k) whether a declaration of conformity is required (see 9.1); l) whether an inspection document is required, and if so, which type (see 9.2); m) whether there are any special requirements for marking, packaging or labelling (see Clause 10). EXAMPLE 1 Ordering details for 100 sheets for electrical purposes conforming to EN 13599, in material designated either Cu-ETP or CW004A, in material condition H040, nominal thickness 6,0 mm, nominal width 600 mm, as manufactured length 2 000 mm: 100 pieces Sheet EN 13599 — Cu-ETP — H040 — 6,0 × 600 × 2 000ML or 100 pieces Sheet EN 13599 — CW004A — H040 — 6,0 × 600 × 2 000ML SIST EN 13599:2014
EN 13599:2014 (E) 8 EXAMPLE 2 Ordering details for 5 000 kg strip for electrical purposes conforming to EN 13599, in material designated either CuAg0,10 or CW013A, in material condition R290, nominal thickness 0,4 mm, normal thickness tolerance, nominal width 60 mm, nominal inside diameter of coil 400 mm, maximum outside diameter of coil 960 mm and approximate specific coil mass (mass per width) 4,5 kg/mm: 5 000 kg Strip EN 13599 — CuAg0,10 — R290 — 0,4N × 60 — nominal inside diameter of coil 400 mm — maximum outside diameter of coil 960 mm — approximate specific coil mass 4,5 kg/mm or 5 000 kg Strip EN 13599 — CW013A — R290 — 0,4N × 60 — nominal inside diameter of coil 400 mm — maximum outside diameter of coil 960 mm — approximate specific coil mass 4,5 kg/mm 6 Requirements 6.1 Composition The composition shall conform to the requirements for the appropriate material given in Table 1. Percentage content of the element shown as “remainder” (Rem.) is usually calculated by difference from 100 %. NOTE For characteristics of coppers for electrical purposes, see Annex A. 6.2 Mechanical properties The mechanical prop
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.