Short Range Devices (SRD) - Radio equipment to be used in the 1 GHz to 40 GHz frequency range - Harmonised Standard for access to radio spectrum

The present document specifies technical characteristics and methods of measurements for the following equipment
types:
1) Non specific Short Range Devices, including alarms, telecommand, telemetry, data transmission in general,
etc.
2) Radio Frequency IDentification (RFID) devices.
3) Radiodetermination devices including detection, movement and alert applications.
These radio equipment types are capable of operating in the permitted frequency bands within the 1 GHz to 40 GHz
range as specified in table 1:
1) with either a Radio Frequency (RF) output connection and dedicated antenna or an integral antenna;
2) for all types of modulation;
3) with or without speech.
Table 1 shows a list of the frequency bands as designated by the European Commission Decisions on Short Range
Devices [i.5] and the CEPT/ERC Recommendation 70-03 [i.2] as known at the date of publication of the present
document.

Naprave kratkega dosega (SRD) - Radijska oprema, ki se uporablja v frekvenčnem območju od 1 GHz do 40 GHz - Harmonizirani standard za dostop do radijskega spektra

Ta dokument določa tehnične lastnosti in merilne metode za naslednje vrste opreme:
1) nespecifične naprave kratkega dosega, vključno z alarmi, napravami za daljinsko vodenje, telemetrijo, prenosom podatkov v splošnem itd.;
2) naprave za radiofrekvenčno identifikacijo (RFID);
3) radiofrekvenčne naprave za zaznavanje, gibanje in opozarjanje.
Te vrste radijske opreme lahko delujejo v dovoljenih frekvenčnih pasovih v območju od 1 GHz do 40 GHz, kot je opredeljeno v preglednici 1:
1) z radiofrekvenčno (RF) izhodno povezavo in namensko anteno ali z vgrajeno anteno;
2) za vse vrste modulacije;
3) z govorom ali brez.
V preglednici 1 je prikazan seznam frekvenčnih pasov v skladu z odločbami Evropske komisije o napravah kratkega dosega [i.5] in priporočilom CEPT/ERC 70-03 [i.2], znanimi na datum objave tega dokumenta.

General Information

Status
Published
Public Enquiry End Date
17-Dec-2017
Publication Date
04-Sep-2018
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
06-Aug-2018
Due Date
11-Oct-2018
Completion Date
05-Sep-2018

Buy Standard

Standard
SIST EN 300 440 V2.2.1:2018
English language
79 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ETSI EN 300 440 V2.2.1 (2018-07) - Short Range Devices (SRD); Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Harmonised Standard for access to radio spectrum
English language
79 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 300 440 V2.2.1 (2018-05) - Short Range Devices (SRD); Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Harmonised Standard for access to radio spectrum
English language
78 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 300 440 V2.2.0 (2017-09) - Short Range Devices (SRD); Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Harmonised Standard for access to radio spectrum
English language
77 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.UDGLMVNHJDVSHNWUDShort Range Devices (SRD) - Radio equipment to be used in the 1 GHz to 40 GHz frequency range - Harmonised Standard for access to radio spectrum33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:ETSI EN 300 440 V2.2.1 (2018-07)SIST EN 300 440 V2.2.1:2018en01-oktober-2018SIST EN 300 440 V2.2.1:2018SLOVENSKI

STANDARD
SIST EN 300 440 V2.2.1:2018

ETSI EN 300 440 V2.2.1 (2018-07) Short Range Devices (SRD); Radio equipment to be used in

the 1 GHz to 40 GHz frequency range; Harmonised Standard for access to radio spectrum

HARMONISED EUROPEAN STANDARD SIST EN 300 440 V2.2.1:2018
ETSI ETSI EN 300 440 V2.2.1 (2018-07) 2

Reference REN/ERM-TG28-551 Keywords harmonised standard, radio, SRD, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88

Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2018. All rights reserved.

DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETM are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM® and the GSM logo are trademarks registered and owned by the GSM Association. SIST EN 300 440 V2.2.1:2018

ETSI ETSI EN 300 440 V2.2.1 (2018-07) 3 Contents Intellectual Property Rights ................................................................................................................................ 8 Foreword ............................................................................................................................................................. 8 Modal verbs terminology .................................................................................................................................... 8 Introduction ........................................................................................................................................................ 9 1 Scope ...................................................................................................................................................... 10 2 References .............................................................................................................................................. 11 2.1 Normative references ....................................................................................................................................... 11 2.2 Informative references ...................................................................................................................................... 11 3 Definitions, symbols and abbreviations ................................................................................................. 12 3.1 Definitions ........................................................................................................................................................ 12 3.2 Symbols ............................................................................................................................................................ 14 3.3 Abbreviations ................................................................................................................................................... 14 4 Technical requirements specifications ................................................................................................... 15 4.1 Environmental profile ....................................................................................................................................... 15 4.2 Transmitter requirements ................................................................................................................................. 15 4.2.1 Transmitter measurement requirements ...................................................................................................... 15 4.2.1.1 Applicability.......................................................................................................................................... 15 4.2.1.2 Methods of measurement and limits for transmitter parameters ........................................................... 15 4.2.2 Equivalent isotropically radiated power (e.i.r.p.) ........................................................................................ 16 4.2.2.1 Applicability.......................................................................................................................................... 16 4.2.2.2 Description ............................................................................................................................................ 16 4.2.2.3 Method of measurement ........................................................................................................................ 16 4.2.2.3.0 General requirements ....................................................................................................................... 16 4.2.2.3.1 Non spread spectrum transmitters with a -6 dB bandwidth of up to 20 MHz and spread spectrum transmitters with channel bandwidth of up to 1 MHz ...................................................... 16 4.2.2.3.2 Transmitters other than those defined in clause 4.2.2.3.1 ................................................................ 17 4.2.2.4 Limits .................................................................................................................................................... 18 4.2.2.5 Conformance ......................................................................................................................................... 18 4.2.3 Permitted range of operating frequencies ................................................................................................... 18 4.2.3.1 Applicability.......................................................................................................................................... 18 4.2.3.2 Description ............................................................................................................................................ 19 4.2.3.3 Method of measurement ........................................................................................................................ 19 4.2.3.4 Method of measurement for equipment using FHSS modulation ......................................................... 19 4.2.3.5 Limits .................................................................................................................................................... 20 4.2.4 Unwanted emissions in the spurious domain .............................................................................................. 20 4.2.4.1 Applicability.......................................................................................................................................... 20 4.2.4.2 Description ............................................................................................................................................ 20 4.2.4.3 Method of measurement ........................................................................................................................ 20 4.2.4.3.0 General Requirements ..................................................................................................................... 20 4.2.4.3.1 Conducted spurious emission .......................................................................................................... 21 4.2.4.3.2 Method of measurement - cabinet spurious radiation ...................................................................... 21 4.2.4.3.3 Method of measurement - radiated spurious emission .................................................................... 22 4.2.4.3.4 Additional requirements for equipment employing FHSS modulation ........................................... 23 4.2.4.4 Limits .................................................................................................................................................... 23 4.2.4.5 Conformance ......................................................................................................................................... 23 4.2.5 Duty cycle ................................................................................................................................................... 23 4.2.5.1 Applicability.......................................................................................................................................... 23 4.2.5.2 Description ............................................................................................................................................ 23 4.2.5.3 Method of measurement ........................................................................................................................ 24 4.2.5.4 Limits .................................................................................................................................................... 24 4.2.5.5 Conformance ......................................................................................................................................... 25 4.2.6 Additional requirements for FHSS equipment ............................................................................................ 25 4.2.6.1 Applicability.......................................................................................................................................... 25 4.2.6.2 Description ............................................................................................................................................ 25 SIST EN 300 440 V2.2.1:2018

ETSI ETSI EN 300 440 V2.2.1 (2018-07) 4 4.2.6.3 Method of measurement ........................................................................................................................ 25 4.2.6.4 Limits .................................................................................................................................................... 25 4.2.6.5 Conformance ......................................................................................................................................... 25 4.3 Receiver requirements ...................................................................................................................................... 25 4.3.1 Receiver category ....................................................................................................................................... 25 4.3.2 General performance criteria ...................................................................................................................... 26 4.3.3 Adjacent channel selectivity ....................................................................................................................... 26 4.3.3.1 Applicability.......................................................................................................................................... 26 4.3.3.2 Description ............................................................................................................................................ 26 4.3.3.3 Method of measurement ........................................................................................................................ 26 4.3.3.4 Limits .................................................................................................................................................... 27 4.3.3.5 Conformance ......................................................................................................................................... 27 4.3.4 Blocking or desensitization ......................................................................................................................... 27 4.3.4.1 Applicability.......................................................................................................................................... 27 4.3.4.2 Description ............................................................................................................................................ 27 4.3.4.3 Methods of measurement ...................................................................................................................... 27 4.3.4.4 Limits .................................................................................................................................................... 28 4.3.4.5 Conformance ......................................................................................................................................... 29 4.3.5 Spurious radiations ..................................................................................................................................... 29 4.3.5.1 Applicability.......................................................................................................................................... 29 4.3.5.2 Description ............................................................................................................................................ 29 4.3.5.3 Method of measurement for spurious radiation..................................................................................... 29 4.3.5.3.0 General Requirements ..................................................................................................................... 29 4.3.5.3.1 Method of measurement conducted spurious components .............................................................. 29 4.3.5.3.2 Method of measurement cabinet radiation....................................................................................... 30 4.3.5.3.3 Method of measurement radiated spurious components .................................................................. 30 4.3.5.4 Limits .................................................................................................................................................... 31 4.3.5.5 Conformance ......................................................................................................................................... 31 4.4 Spectrum access techniques ............................................................................................................................. 31 4.4.1 Applicability ............................................................................................................................................... 31 4.4.2 Listen Before Talk (LBT) ........................................................................................................................... 31 4.4.2.0 General .................................................................................................................................................. 31 4.4.2.1 LBT timing parameters ......................................................................................................................... 32 4.4.2.1.1 Minimum transmitter off-time ......................................................................................................... 32 4.4.2.1.2 LBT minimum listening time .......................................................................................................... 32 4.4.2.1.3 Acknowledge transmissions ............................................................................................................ 33 4.4.2.1.4 Maximum transmitter on-time ......................................................................................................... 33 4.4.2.1.5 Declaration of LBT parameters ....................................................................................................... 33 4.4.2.1.6 Manual and event driven devices .................................................................................................... 33 4.4.2.2 Receiver LBT threshold and transmitter max on-time .......................................................................... 33 4.4.2.2.0 Applicability .................................................................................................................................... 33 4.4.2.2.1 Descriptions ..................................................................................................................................... 34 4.4.2.2.2 Method of measurements................................................................................................................. 34 4.4.2.2.3 Limits .............................................................................................................................................. 34 4.4.2.2.4 Conformance ................................................................................................................................... 35 4.4.3 Detect And Avoid techniques (DAA) ......................................................................................................... 35 4.4.3.1 General requirements ............................................................................................................................ 35 4.4.4 Adaptive Frequency Agility (AFA) ............................................................................................................ 35 4.4.4.1 General requirements ............................................................................................................................ 35 4.5 2,45 GHz RFID systems ................................................................................................................................... 36 4.6 GBSAR systems ............................................................................................................................................... 36 4.6.1 Effective radiated power ............................................................................................................................. 36 4.6.2 Permitted range of operating frequencies ................................................................................................... 36 4.6.3 DAA threshold ............................................................................................................................................ 36 4.6.3.0 General requirements ............................................................................................................................ 36 4.6.3.1 DAA timing parameters ........................................................................................................................ 36 4.6.3.1.1 Minimum listen time ....................................................................................................................... 36 4.6.3.1.2 Minimum listen time after detection................................................................................................ 36 4.6.3.1.3 Maximum transmitter on-time ......................................................................................................... 36 4.6.3.1.4 Minimum transmitter off-time ......................................................................................................... 36 4.6.4 Antenna pattern ........................................................................................................................................... 36 SIST EN 300 440 V2.2.1:2018

ETSI ETSI EN 300 440 V2.2.1 (2018-07) 5 5 Testing for compliance with technical requirements .............................................................................. 36 5.1 Environmental conditions for testing ............................................................................................................... 36 5.2 Presentation of equipment for testing purposes ................................................................................................ 37 5.2.0 General ........................................................................................................................................................ 37 5.2.1 Choice of model for testing ........................................................................................................................ 37 5.2.2 Testing of equipment with alternative power levels ................................................................................... 37 5.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) .................................................................................................................................................. 37 5.2.3.1 Equipment with an internal permanent or temporary antenna connector or using a dedicated test fixture .................................................................................................................................................... 37 5.2.3.2 Equipment with a temporary antenna connector ................................................................................... 38 5.2.4 Testing of devices using duty cycle ............................................................................................................ 38 5.3 Mechanical and electrical design ...................................................................................................................... 38 5.3.1 General ........................................................................................................................................................ 38 5.3.2 Void ............................................................................................................................................................ 38 5.3.3 Transmitter shut-off facility ........................................................................................................................ 38 5.3.4 Receiver mute or squelch ............................................................................................................................ 38 5.4 Auxiliary test equipment .................................................................................................................................. 38 5.5 Test power source ............................................................................................................................................. 39 5.5.0 General ........................................................................................................................................................ 39 5.5.1 External test power source .......................................................................................................................... 39 5.5.2 Internal test power source ........................................................................................................................... 39 5.6 Normal test conditions ...................................................................................................................................... 39 5.6.1 Normal temperature and humidity .............................................................................................................. 39 5.6.2 Normal test power source ........................................................................................................................... 39 5.6.2.1 Mains voltage ........................................................................................................................................ 39 5.6.2.2 Battery power sources ........................................................................................................................... 40 5.6.2.3 Other power sources .............................................................................................................................. 40 5.7 Extreme test conditions .................................................................................................................................... 40 5.7.1 Extreme temperatures ................................................................................................................................. 40 5.7.1.1 Procedure for tests at extreme temperatures .......................................................................................... 40 5.7.1.1.0 General ............................................................................................................................................ 40 5.7.1.1.1 Procedure for equipment designed for continuous operation .......................................................... 40 5.7.1.1.2 Procedure for equipment designed for intermittent operation ......................................................... 40 5.7.1.2 Extreme temperature ranges .................................................................................................................. 41 5.7.2 Extreme test source voltages ....................................................................................................................... 41 5.7.2.1 Mains voltage ........................................................................................................................................ 41 5.7.2.2 Battery power sources ........................................................................................................................... 41 5.7.2.3 Power sources using other types of batteries ......................................................................................... 41 5.7.2.4 Other power sources .............................................................................................................................. 41 5.8 General conditions ............................................................................................................................................ 42 5.8.1 Normal test signals and test modulation ..................................................................................................... 42 5.8.1.0 General .................................................................................................................................................. 42 5.8.1.1 Normal test signals for data ................................................................................................................... 42 5.8.2 Artificial antenna ........................................................................................................................................ 42 5.8.3 Test fixture .................................................................................................................................................. 43 5.8.3.0 General .................................................................................................................................................. 43 5.8.3.1 Validation of the test-fixture in the temperature chamber ..................................................................... 44 5.8.3.2 Mode of use ........................................................................................................................................... 45 5.8.4 Test sites and general arrangements for radiated measurements ................................................................ 46 5.8.5 Measuring receiver ..................................................................................................................................... 46 5.9 Interpretation of the measurement results ........................................................................................................ 46 5.9.0 General ........................................................................................................................................................ 46 5.9.1 Measurement uncertainty is greater than maximum acceptable uncertainty ............................................... 47 Annex A (informative):

Relationship between the present document and the essential requirements of Directive 2014/53/EU ......................................................... 48 Annex B (normative):

EU wide harmonised national radio interfaces from 1 GHz to 40 GHz ... 50 Annex C (informative):

National Radio Interfaces not EU wide harmonised .................................. 51 SIST EN 300 440 V2.2.1:2018

ETSI ETSI EN 300 440 V2.2.1 (2018-07) 6 Annex D (informative):

Selection of technical parameters ................................................................. 53 D.1 Int

...

ETSI EN 300 440 V2.2.1 (2018-07)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Radio equipment to be used in
the 1 GHz to 40 GHz frequency range;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 ETSI EN 300 440 V2.2.1 (2018-07)
Reference
REN/ERM-TG28-551
Keywords
harmonised standard, radio, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

TM TM

3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 440 V2.2.1 (2018-07)
Contents

Intellectual Property Rights ................................................................................................................................ 8

Foreword ............................................................................................................................................................. 8

Modal verbs terminology .................................................................................................................................... 8

Introduction ........................................................................................................................................................ 9

1 Scope ...................................................................................................................................................... 10

2 References .............................................................................................................................................. 11

2.1 Normative references ....................................................................................................................................... 11

2.2 Informative references ...................................................................................................................................... 11

3 Definitions, symbols and abbreviations ................................................................................................. 12

3.1 Definitions ........................................................................................................................................................ 12

3.2 Symbols ............................................................................................................................................................ 14

3.3 Abbreviations ................................................................................................................................................... 14

4 Technical requirements specifications ................................................................................................... 15

4.1 Environmental profile ....................................................................................................................................... 15

4.2 Transmitter requirements ................................................................................................................................. 15

4.2.1 Transmitter measurement requirements ...................................................................................................... 15

4.2.1.1 Applicability.......................................................................................................................................... 15

4.2.1.2 Methods of measurement and limits for transmitter parameters ........................................................... 15

4.2.2 Equivalent isotropically radiated power (e.i.r.p.) ........................................................................................ 16

4.2.2.1 Applicability.......................................................................................................................................... 16

4.2.2.2 Description ............................................................................................................................................ 16

4.2.2.3 Method of measurement ........................................................................................................................ 16

4.2.2.3.0 General requirements ....................................................................................................................... 16

4.2.2.3.1 Non spread spectrum transmitters with a -6 dB bandwidth of up to 20 MHz and spread

spectrum transmitters with channel bandwidth of up to 1 MHz ...................................................... 16

4.2.2.3.2 Transmitters other than those defined in clause 4.2.2.3.1 ................................................................ 17

4.2.2.4 Limits .................................................................................................................................................... 18

4.2.2.5 Conformance ......................................................................................................................................... 18

4.2.3 Permitted range of operating frequencies ................................................................................................... 18

4.2.3.1 Applicability.......................................................................................................................................... 18

4.2.3.2 Description ............................................................................................................................................ 19

4.2.3.3 Method of measurement ........................................................................................................................ 19

4.2.3.4 Method of measurement for equipment using FHSS modulation ......................................................... 19

4.2.3.5 Limits .................................................................................................................................................... 20

4.2.4 Unwanted emissions in the spurious domain .............................................................................................. 20

4.2.4.1 Applicability.......................................................................................................................................... 20

4.2.4.2 Description ............................................................................................................................................ 20

4.2.4.3 Method of measurement ........................................................................................................................ 20

4.2.4.3.0 General Requirements ..................................................................................................................... 20

4.2.4.3.1 Conducted spurious emission .......................................................................................................... 21

4.2.4.3.2 Method of measurement - cabinet spurious radiation ...................................................................... 21

4.2.4.3.3 Method of measurement - radiated spurious emission .................................................................... 22

4.2.4.3.4 Additional requirements for equipment employing FHSS modulation ........................................... 23

4.2.4.4 Limits .................................................................................................................................................... 23

4.2.4.5 Conformance ......................................................................................................................................... 23

4.2.5 Duty cycle ................................................................................................................................................... 23

4.2.5.1 Applicability.......................................................................................................................................... 23

4.2.5.2 Description ............................................................................................................................................ 23

4.2.5.3 Method of measurement ........................................................................................................................ 24

4.2.5.4 Limits .................................................................................................................................................... 24

4.2.5.5 Conformance ......................................................................................................................................... 25

4.2.6 Additional requirements for FHSS equipment ............................................................................................ 25

4.2.6.1 Applicability.......................................................................................................................................... 25

4.2.6.2 Description ............................................................................................................................................ 25

ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 440 V2.2.1 (2018-07)

4.2.6.3 Method of measurement ........................................................................................................................ 25

4.2.6.4 Limits .................................................................................................................................................... 25

4.2.6.5 Conformance ......................................................................................................................................... 25

4.3 Receiver requirements ...................................................................................................................................... 25

4.3.1 Receiver category ....................................................................................................................................... 25

4.3.2 General performance criteria ...................................................................................................................... 26

4.3.3 Adjacent channel selectivity ....................................................................................................................... 26

4.3.3.1 Applicability.......................................................................................................................................... 26

4.3.3.2 Description ............................................................................................................................................ 26

4.3.3.3 Method of measurement ........................................................................................................................ 26

4.3.3.4 Limits .................................................................................................................................................... 27

4.3.3.5 Conformance ......................................................................................................................................... 27

4.3.4 Blocking or desensitization ......................................................................................................................... 27

4.3.4.1 Applicability.......................................................................................................................................... 27

4.3.4.2 Description ............................................................................................................................................ 27

4.3.4.3 Methods of measurement ...................................................................................................................... 27

4.3.4.4 Limits .................................................................................................................................................... 28

4.3.4.5 Conformance ......................................................................................................................................... 29

4.3.5 Spurious radiations ..................................................................................................................................... 29

4.3.5.1 Applicability.......................................................................................................................................... 29

4.3.5.2 Description ............................................................................................................................................ 29

4.3.5.3 Method of measurement for spurious radiation..................................................................................... 29

4.3.5.3.0 General Requirements ..................................................................................................................... 29

4.3.5.3.1 Method of measurement conducted spurious components .............................................................. 29

4.3.5.3.2 Method of measurement cabinet radiation....................................................................................... 30

4.3.5.3.3 Method of measurement radiated spurious components .................................................................. 30

4.3.5.4 Limits .................................................................................................................................................... 31

4.3.5.5 Conformance ......................................................................................................................................... 31

4.4 Spectrum access techniques ............................................................................................................................. 31

4.4.1 Applicability ............................................................................................................................................... 31

4.4.2 Listen Before Talk (LBT) ........................................................................................................................... 31

4.4.2.0 General .................................................................................................................................................. 31

4.4.2.1 LBT timing parameters ......................................................................................................................... 32

4.4.2.1.1 Minimum transmitter off-time ......................................................................................................... 32

4.4.2.1.2 LBT minimum listening time .......................................................................................................... 32

4.4.2.1.3 Acknowledge transmissions ............................................................................................................ 33

4.4.2.1.4 Maximum transmitter on-time ......................................................................................................... 33

4.4.2.1.5 Declaration of LBT parameters ....................................................................................................... 33

4.4.2.1.6 Manual and event driven devices .................................................................................................... 33

4.4.2.2 Receiver LBT threshold and transmitter max on-time .......................................................................... 33

4.4.2.2.0 Applicability .................................................................................................................................... 33

4.4.2.2.1 Descriptions ..................................................................................................................................... 34

4.4.2.2.2 Method of measurements................................................................................................................. 34

4.4.2.2.3 Limits .............................................................................................................................................. 34

4.4.2.2.4 Conformance ................................................................................................................................... 35

4.4.3 Detect And Avoid techniques (DAA) ......................................................................................................... 35

4.4.3.1 General requirements ............................................................................................................................ 35

4.4.4 Adaptive Frequency Agility (AFA) ............................................................................................................ 35

4.4.4.1 General requirements ............................................................................................................................ 35

4.5 2,45 GHz RFID systems ................................................................................................................................... 36

4.6 GBSAR systems ............................................................................................................................................... 36

4.6.1 Effective radiated power ............................................................................................................................. 36

4.6.2 Permitted range of operating frequencies ................................................................................................... 36

4.6.3 DAA threshold ............................................................................................................................................ 36

4.6.3.0 General requirements ............................................................................................................................ 36

4.6.3.1 DAA timing parameters ........................................................................................................................ 36

4.6.3.1.1 Minimum listen time ....................................................................................................................... 36

4.6.3.1.2 Minimum listen time after detection................................................................................................ 36

4.6.3.1.3 Maximum transmitter on-time ......................................................................................................... 36

4.6.3.1.4 Minimum transmitter off-time ......................................................................................................... 36

4.6.4 Antenna pattern ........................................................................................................................................... 36

ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 440 V2.2.1 (2018-07)

5 Testing for compliance with technical requirements .............................................................................. 36

5.1 Environmental conditions for testing ............................................................................................................... 36

5.2 Presentation of equipment for testing purposes ................................................................................................ 37

5.2.0 General ........................................................................................................................................................ 37

5.2.1 Choice of model for testing ........................................................................................................................ 37

5.2.2 Testing of equipment with alternative power levels ................................................................................... 37

5.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna

equipment) .................................................................................................................................................. 37

5.2.3.1 Equipment with an internal permanent or temporary antenna connector or using a dedicated test

fixture .................................................................................................................................................... 37

5.2.3.2 Equipment with a temporary antenna connector ................................................................................... 38

5.2.4 Testing of devices using duty cycle ............................................................................................................ 38

5.3 Mechanical and electrical design ...................................................................................................................... 38

5.3.1 General ........................................................................................................................................................ 38

5.3.2 Void ............................................................................................................................................................ 38

5.3.3 Transmitter shut-off facility ........................................................................................................................ 38

5.3.4 Receiver mute or squelch ............................................................................................................................ 38

5.4 Auxiliary test equipment .................................................................................................................................. 38

5.5 Test power source ............................................................................................................................................. 39

5.5.0 General ........................................................................................................................................................ 39

5.5.1 External test power source .......................................................................................................................... 39

5.5.2 Internal test power source ........................................................................................................................... 39

5.6 Normal test conditions ...................................................................................................................................... 39

5.6.1 Normal temperature and humidity .............................................................................................................. 39

5.6.2 Normal test power source ........................................................................................................................... 39

5.6.2.1 Mains voltage ........................................................................................................................................ 39

5.6.2.2 Battery power sources ........................................................................................................................... 40

5.6.2.3 Other power sources .............................................................................................................................. 40

5.7 Extreme test conditions .................................................................................................................................... 40

5.7.1 Extreme temperatures ................................................................................................................................. 40

5.7.1.1 Procedure for tests at extreme temperatures .......................................................................................... 40

5.7.1.1.0 General ............................................................................................................................................ 40

5.7.1.1.1 Procedure for equipment designed for continuous operation .......................................................... 40

5.7.1.1.2 Procedure for equipment designed for intermittent operation ......................................................... 40

5.7.1.2 Extreme temperature ranges .................................................................................................................. 41

5.7.2 Extreme test source voltages ....................................................................................................................... 41

5.7.2.1 Mains voltage ........................................................................................................................................ 41

5.7.2.2 Battery power sources ........................................................................................................................... 41

5.7.2.3 Power sources using other types of batteries ......................................................................................... 41

5.7.2.4 Other power sources .............................................................................................................................. 41

5.8 General conditions ............................................................................................................................................ 42

5.8.1 Normal test signals and test modulation ..................................................................................................... 42

5.8.1.0 General .................................................................................................................................................. 42

5.8.1.1 Normal test signals for data ................................................................................................................... 42

5.8.2 Artificial antenna ........................................................................................................................................ 42

5.8.3 Test fixture .................................................................................................................................................. 43

5.8.3.0 General .................................................................................................................................................. 43

5.8.3.1 Validation of the test-fixture in the temperature chamber ..................................................................... 44

5.8.3.2 Mode of use ........................................................................................................................................... 45

5.8.4 Test sites and general arrangements for radiated measurements ................................................................ 46

5.8.5 Measuring receiver ..................................................................................................................................... 46

5.9 Interpretation of the measurement results ........................................................................................................ 46

5.9.0 General ........................................................................................................................................................ 46

5.9.1 Measurement uncertainty is greater than maximum acceptable uncertainty ............................................... 47

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 48

Annex B (normative): EU wide harmonised national radio interfaces from 1 GHz to 40 GHz ... 50

Annex C (informative): National Radio Interfaces not EU wide harmonised .................................. 51

ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 440 V2.2.1 (2018-07)

Annex D (informative): Selection of technical parameters ................................................................. 53

D.1 Introduction ............................................................................................................................................ 53

D.2 Receiver parameters ...................................................
...

Final draft ETSI EN 300 440 V2.2.1 (2018-05)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Radio equipment to be used in
the 1 GHz to 40 GHz frequency range;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 440 V2.2.1 (2018-05)
Reference
REN/ERM-TG28-551
Keywords
harmonised standard, radio, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

TM TM

3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 440 V2.2.1 (2018-05)
Contents

Intellectual Property Rights ................................................................................................................................ 8

Foreword ............................................................................................................................................................. 8

Modal verbs terminology .................................................................................................................................... 8

Introduction ........................................................................................................................................................ 9

1 Scope ...................................................................................................................................................... 10

2 References .............................................................................................................................................. 11

2.1 Normative references ....................................................................................................................................... 11

2.2 Informative references ...................................................................................................................................... 11

3 Definitions, symbols and abbreviations ................................................................................................. 12

3.1 Definitions ........................................................................................................................................................ 12

3.2 Symbols ............................................................................................................................................................ 14

3.3 Abbreviations ................................................................................................................................................... 14

4 Technical requirements specifications ................................................................................................... 15

4.1 Environmental profile ....................................................................................................................................... 15

4.2 Transmitter requirements ................................................................................................................................. 15

4.2.1 Transmitter measurement requirements ...................................................................................................... 15

4.2.1.1 Applicability.......................................................................................................................................... 15

4.2.1.2 Methods of measurement and limits for transmitter parameters ........................................................... 15

4.2.2 Equivalent isotropically radiated power (e.i.r.p.) ........................................................................................ 15

4.2.2.1 Applicability.......................................................................................................................................... 15

4.2.2.2 Description ............................................................................................................................................ 16

4.2.2.3 Method of measurement ........................................................................................................................ 16

4.2.2.3.0 General requirements ....................................................................................................................... 16

4.2.2.3.1 Non spread spectrum transmitters with a -6 dB bandwidth of up to 20 MHz and spread

spectrum transmitters with channel bandwidth of up to 1 MHz ...................................................... 16

4.2.2.3.2 Transmitters other than those defined in clause 4.2.2.3.1 ................................................................ 17

4.2.2.4 Limits .................................................................................................................................................... 18

4.2.2.5 Conformance ......................................................................................................................................... 18

4.2.3 Permitted range of operating frequencies ................................................................................................... 18

4.2.3.1 Applicability.......................................................................................................................................... 18

4.2.3.2 Description ............................................................................................................................................ 18

4.2.3.3 Method of measurement ........................................................................................................................ 19

4.2.3.4 Method of measurement for equipment using FHSS modulation ......................................................... 19

4.2.3.5 Limits .................................................................................................................................................... 20

4.2.4 Unwanted emissions in the spurious domain .............................................................................................. 20

4.2.4.1 Applicability.......................................................................................................................................... 20

4.2.4.2 Description ............................................................................................................................................ 20

4.2.4.3 Method of measurement ........................................................................................................................ 20

4.2.4.3.0 General Requirements ..................................................................................................................... 20

4.2.4.3.1 Conducted spurious emission .......................................................................................................... 21

4.2.4.3.2 Method of measurement - cabinet spurious radiation ...................................................................... 21

4.2.4.3.3 Method of measurement - radiated spurious emission .................................................................... 22

4.2.4.3.4 Additional requirements for equipment employing FHSS modulation ........................................... 23

4.2.4.4 Limits .................................................................................................................................................... 23

4.2.4.5 Conformance ......................................................................................................................................... 23

4.2.5 Duty cycle ................................................................................................................................................... 23

4.2.5.1 Applicability.......................................................................................................................................... 23

4.2.5.2 Description ............................................................................................................................................ 23

4.2.5.3 Method of measurement ........................................................................................................................ 24

4.2.5.4 Limits .................................................................................................................................................... 24

4.2.5.5 Conformance ......................................................................................................................................... 24

4.2.6 Additional requirements for FHSS equipment ............................................................................................ 25

4.2.6.1 Applicability.......................................................................................................................................... 25

4.2.6.2 Description ............................................................................................................................................ 25

ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 440 V2.2.1 (2018-05)

4.2.6.3 Method of measurement ........................................................................................................................ 25

4.2.6.4 Limits .................................................................................................................................................... 25

4.2.6.5 Conformance ......................................................................................................................................... 25

4.3 Receiver requirements ...................................................................................................................................... 25

4.3.1 Receiver category ....................................................................................................................................... 25

4.3.2 General performance criteria ...................................................................................................................... 26

4.3.3 Adjacent channel selectivity ....................................................................................................................... 26

4.3.3.1 Applicability.......................................................................................................................................... 26

4.3.3.2 Description ............................................................................................................................................ 26

4.3.3.3 Method of measurement ........................................................................................................................ 26

4.3.3.4 Limits .................................................................................................................................................... 27

4.3.3.5 Conformance ......................................................................................................................................... 27

4.3.4 Blocking or desensitization ......................................................................................................................... 27

4.3.4.1 Applicability.......................................................................................................................................... 27

4.3.4.2 Description ............................................................................................................................................ 27

4.3.4.3 Methods of measurement ...................................................................................................................... 27

4.3.4.4 Limits .................................................................................................................................................... 28

4.3.4.5 Conformance ......................................................................................................................................... 28

4.3.5 Spurious radiations ..................................................................................................................................... 28

4.3.5.1 Applicability.......................................................................................................................................... 28

4.3.5.2 Description ............................................................................................................................................ 28

4.3.5.3 Method of measurement for spurious radiation..................................................................................... 29

4.3.5.3.0 General Requirements ..................................................................................................................... 29

4.3.5.3.1 Method of measurement conducted spurious components .............................................................. 29

4.3.5.3.2 Method of measurement cabinet radiation....................................................................................... 29

4.3.5.3.3 Method of measurement radiated spurious components .................................................................. 30

4.3.5.4 Limits .................................................................................................................................................... 30

4.3.5.5 Conformance ......................................................................................................................................... 30

4.4 Spectrum access techniques ............................................................................................................................. 30

4.4.1 Applicability ............................................................................................................................................... 30

4.4.2 Listen Before Talk (LBT) ........................................................................................................................... 31

4.4.2.0 General .................................................................................................................................................. 31

4.4.2.1 LBT timing parameters ......................................................................................................................... 31

4.4.2.1.1 Minimum transmitter off-time ......................................................................................................... 31

4.4.2.1.2 LBT minimum listening time .......................................................................................................... 31

4.4.2.1.3 Acknowledge transmissions ............................................................................................................ 32

4.4.2.1.4 Maximum transmitter on-time ......................................................................................................... 32

4.4.2.1.5 Declaration of LBT parameters ....................................................................................................... 33

4.4.2.1.6 Manual and event driven devices .................................................................................................... 33

4.4.2.2 Receiver LBT threshold and transmitter max on-time .......................................................................... 33

4.4.2.2.0 Applicability .................................................................................................................................... 33

4.4.2.2.1 Descriptions ..................................................................................................................................... 33

4.4.2.2.2 Method of measurements................................................................................................................. 33

4.4.2.2.3 Limits .............................................................................................................................................. 34

4.4.2.2.4 Conformance ................................................................................................................................... 34

4.4.3 Detect And Avoid techniques (DAA) ......................................................................................................... 34

4.4.3.1 General requirements ............................................................................................................................ 34

4.4.4 Adaptive Frequency Agility (AFA) ............................................................................................................ 35

4.4.4.1 General requirements ............................................................................................................................ 35

4.5 2,45 GHz RFID systems ................................................................................................................................... 35

4.6 GBSAR systems ............................................................................................................................................... 35

4.6.1 Effective radiated power ............................................................................................................................. 35

4.6.2 Permitted range of operating frequencies ................................................................................................... 35

4.6.3 DAA threshold ............................................................................................................................................ 35

4.6.3.0 General requirements ............................................................................................................................ 35

4.6.3.1 DAA timing parameters ........................................................................................................................ 35

4.6.3.1.1 Minimum listen time ....................................................................................................................... 35

4.6.3.1.2 Minimum listen time after detection................................................................................................ 35

4.6.3.1.3 Maximum transmitter on-time ......................................................................................................... 35

4.6.3.1.4 Minimum transmitter off-time ......................................................................................................... 36

4.6.4 Antenna pattern ........................................................................................................................................... 36

ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 440 V2.2.1 (2018-05)

5 Testing for compliance with technical requirements .............................................................................. 36

5.1 Environmental conditions for testing ............................................................................................................... 36

5.2 Presentation of equipment for testing purposes ................................................................................................ 36

5.2.0 General ........................................................................................................................................................ 36

5.2.1 Choice of model for testing ........................................................................................................................ 36

5.2.2 Testing of equipment with alternative power levels ................................................................................... 36

5.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna

equipment) .................................................................................................................................................. 37

5.2.3.1 Equipment with an internal permanent or temporary antenna connector or using a dedicated test

fixture .................................................................................................................................................... 37

5.2.3.2 Equipment with a temporary antenna connector ................................................................................... 37

5.2.4 Testing of devices using duty cycle ............................................................................................................ 37

5.3 Mechanical and electrical design ...................................................................................................................... 37

5.3.1 General ........................................................................................................................................................ 37

5.3.2 Void ............................................................................................................................................................ 37

5.3.3 Transmitter shut-off facility ........................................................................................................................ 37

5.3.4 Receiver mute or squelch ............................................................................................................................ 37

5.4 Auxiliary test equipment .................................................................................................................................. 38

5.5 Test power source ............................................................................................................................................. 38

5.5.0 General ........................................................................................................................................................ 38

5.5.1 External test power source .......................................................................................................................... 38

5.5.2 Internal test power source ........................................................................................................................... 38

5.6 Normal test conditions ...................................................................................................................................... 38

5.6.1 Normal temperature and humidity .............................................................................................................. 38

5.6.2 Normal test power source ........................................................................................................................... 39

5.6.2.1 Mains voltage ........................................................................................................................................ 39

5.6.2.2 Battery power sources ........................................................................................................................... 39

5.6.2.3 Other power sources .............................................................................................................................. 39

5.7 Extreme test conditions .................................................................................................................................... 39

5.7.1 Extreme temperatures ................................................................................................................................. 39

5.7.1.1 Procedure for tests at extreme temperatures .......................................................................................... 39

5.7.1.1.0 General ............................................................................................................................................ 39

5.7.1.1.1 Procedure for equipment designed for continuous operation .......................................................... 39

5.7.1.1.2 Procedure for equipment designed for intermittent operation ......................................................... 40

5.7.1.2 Extreme temperature ranges .................................................................................................................. 40

5.7.2 Extreme test source voltages ....................................................................................................................... 40

5.7.2.1 Mains voltage ........................................................................................................................................ 40

5.7.2.2 Battery power sources ........................................................................................................................... 40

5.7.2.3 Power sources using other types of batteries ......................................................................................... 40

5.7.2.4 Other power sources .............................................................................................................................. 41

5.8 General conditions ............................................................................................................................................ 41

5.8.1 Normal test signals and test modulation ..................................................................................................... 41

5.8.1.0 General .................................................................................................................................................. 41

5.8.1.1 Normal test signals for data ................................................................................................................... 41

5.8.2 Artificial antenna ........................................................................................................................................ 42

5.8.3 Test fixture .................................................................................................................................................. 42

5.8.3.0 General .................................................................................................................................................. 42

5.8.3.1 Validation of the test-fixture in the temperature chamber ..................................................................... 43

5.8.3.2 Mode of use ........................................................................................................................................... 45

5.8.4 Test sites and general arrangements for radiated measurements ................................................................ 45

5.8.5 Measuring receiver ..................................................................................................................................... 45

5.9 Interpretation of the measurement results ........................................................................................................ 45

5.9.0 General ........................................................................................................................................................ 45

5.9.1 Measurement uncertainty is greater than maximum acceptable uncertainty ............................................... 46

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 47

Annex B (normative): EU wide harmonised national radio interfaces from 1 GHz to 40 GHz ... 49

Annex C (informative): National Radio Interfaces not EU wide harmonised .................................. 50

ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 300 440 V2.2.1 (2018-05)

Annex D (informative): Selection of technical parameters ................................................................. 52

D.1 Introduction ............................................................................................................................................ 52

D.2 Receiver
...

Draft ETSI EN 300 440 V2.2.0 (2017-09)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Radio equipment to be used in
the 1 GHz to 40 GHz frequency range;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 440 V2.2.0 (2017-09)
Reference
REN/ERM-TG28-551
Keywords
harmonised standard, radio, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.

GSM® and the GSM logo are trademarks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 440 V2.2.0 (2017-09)
Contents

Intellectual Property Rights ................................................................................................................................ 8

Foreword ............................................................................................................................................................. 8

Modal verbs terminology .................................................................................................................................... 8

Introduction ........................................................................................................................................................ 9

1 Scope ...................................................................................................................................................... 10

2 References .............................................................................................................................................. 11

2.1 Normative references ....................................................................................................................................... 11

2.2 Informative references ...................................................................................................................................... 11

3 Definitions, symbols and abbreviations ................................................................................................. 12

3.1 Definitions ........................................................................................................................................................ 12

3.2 Symbols ............................................................................................................................................................ 14

3.3 Abbreviations ................................................................................................................................................... 14

4 Technical requirements specifications ................................................................................................... 15

4.1 Environmental profile ....................................................................................................................................... 15

4.2 Transmitter requirements ................................................................................................................................. 15

4.2.1 Transmitter measurement requirements ...................................................................................................... 15

4.2.1.1 Applicability.......................................................................................................................................... 15

4.2.1.2 Methods of measurement and limits for transmitter parameters ........................................................... 15

4.2.2 Equivalent isotropically radiated power (e.i.r.p.) ........................................................................................ 15

4.2.2.1 Applicability.......................................................................................................................................... 15

4.2.2.2 Description ............................................................................................................................................ 16

4.2.2.3 Method of measurement ........................................................................................................................ 16

4.2.2.3.0 General requirements ....................................................................................................................... 16

4.2.2.3.1 Non spread spectrum transmitters with a -6 dB bandwidth of up to 20 MHz and spread

spectrum transmitters with channel bandwidth of up to 1 MHz ...................................................... 16

4.2.2.3.2 Transmitters other than those defined in clause 4.2.2.3.1 ................................................................ 17

4.2.2.4 Limits .................................................................................................................................................... 18

4.2.2.5 Conformance ......................................................................................................................................... 18

4.2.3 Permitted range of operating frequencies ................................................................................................... 18

4.2.3.1 Applicability.......................................................................................................................................... 18

4.2.3.2 Description ............................................................................................................................................ 18

4.2.3.3 Method of measurement ........................................................................................................................ 19

4.2.3.4 Method of measurement for equipment using FHSS modulation ......................................................... 19

4.2.3.5 Limits .................................................................................................................................................... 20

4.2.4 Unwanted emissions in the spurious domain .............................................................................................. 20

4.2.4.1 Applicability.......................................................................................................................................... 20

4.2.4.2 Description ............................................................................................................................................ 20

4.2.4.3 Method of measurement ........................................................................................................................ 20

4.2.4.3.0 General Requirements ..................................................................................................................... 20

4.2.4.3.1 Conducted spurious emission .......................................................................................................... 21

4.2.4.3.2 Method of measurement - cabinet spurious radiation ...................................................................... 21

4.2.4.3.3 Method of measurement - radiated spurious emission .................................................................... 22

4.2.4.3.4 Additional requirements for equipment employing FHSS modulation ........................................... 23

4.2.4.4 Limits .................................................................................................................................................... 23

4.2.4.5 Conformance ......................................................................................................................................... 23

4.2.5 Duty cycle ................................................................................................................................................... 23

4.2.5.1 Applicability.......................................................................................................................................... 23

4.2.5.2 Description ............................................................................................................................................ 23

4.2.5.3 Method of measurement ........................................................................................................................ 23

4.2.5.4 Limits .................................................................................................................................................... 24

4.2.5.5 Conformance ......................................................................................................................................... 24

4.2.6 Additional requirements for FHSS equipment ............................................................................................ 25

4.2.6.1 Applicability.......................................................................................................................................... 25

4.2.6.2 Description ............................................................................................................................................ 25

ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 440 V2.2.0 (2017-09)

4.2.6.3 Method of measurement ........................................................................................................................ 25

4.2.6.4 Limits .................................................................................................................................................... 25

4.2.6.5 Conformance ......................................................................................................................................... 25

4.3 Receiver requirements ...................................................................................................................................... 25

4.3.1 Receiver category ....................................................................................................................................... 25

4.3.2 General performance criteria ...................................................................................................................... 26

4.3.3 Adjacent channel selectivity ....................................................................................................................... 26

4.3.3.1 Applicability.......................................................................................................................................... 26

4.3.3.2 Description ............................................................................................................................................ 26

4.3.3.3 Method of measurement ........................................................................................................................ 26

4.3.3.4 Limits .................................................................................................................................................... 27

4.3.3.5 Conformance ......................................................................................................................................... 27

4.3.4 Blocking or desensitization ......................................................................................................................... 27

4.3.4.1 Applicability.......................................................................................................................................... 27

4.3.4.2 Description ............................................................................................................................................ 27

4.3.4.3 Methods of measurement ...................................................................................................................... 27

4.3.4.4 Limits .................................................................................................................................................... 28

4.3.4.5 Conformance ......................................................................................................................................... 28

4.3.5 Spurious radiations ..................................................................................................................................... 28

4.3.5.1 Applicability.......................................................................................................................................... 28

4.3.5.2 Description ............................................................................................................................................ 28

4.3.5.3 Method of measurement for spurious radiation..................................................................................... 29

4.3.5.3.0 General Requirements ..................................................................................................................... 29

4.3.5.3.1 Method of measurement conducted spurious components .............................................................. 29

4.3.5.3.2 Method of measurement cabinet radiation....................................................................................... 29

4.3.5.3.3 Method of measurement radiated spurious components .................................................................. 30

4.3.5.4 Limits .................................................................................................................................................... 30

4.3.5.5 Conformance ......................................................................................................................................... 30

4.4 Spectrum access techniques ............................................................................................................................. 30

4.4.1 Applicability ............................................................................................................................................... 30

4.4.2 Listen Before Talk (LBT) ........................................................................................................................... 31

4.4.2.0 General .................................................................................................................................................. 31

4.4.2.1 LBT timing parameters ......................................................................................................................... 31

4.4.2.1.1 Minimum transmitter off-time ......................................................................................................... 31

4.4.2.1.2 LBT minimum listening time .......................................................................................................... 32

4.4.2.1.3 Acknowledge transmissions ............................................................................................................ 32

4.4.2.1.4 Maximum transmitter on-time ......................................................................................................... 32

4.4.2.1.5 Declaration of LBT parameters ....................................................................................................... 33

4.4.2.1.6 Equipment with or without LBT using transmitter time-out-timer .................................................. 33

4.4.2.2 Receiver LBT threshold and transmitter max on-time .......................................................................... 33

4.4.2.2.0 Applicability .................................................................................................................................... 33

4.4.2.2.1 Descriptions ..................................................................................................................................... 33

4.4.2.2.2 Method of measurements................................................................................................................. 33

4.4.2.2.3 Limits .............................................................................................................................................. 34

4.4.2.2.4 Conformance ................................................................................................................................... 34

4.4.3 Detect And Avoid techniques (DAA) ......................................................................................................... 34

4.4.3.1 General requirements ............................................................................................................................ 34

4.4.4 Adaptive Frequency Agility (AFA) ............................................................................................................ 35

4.4.4.1 General requirements ............................................................................................................................ 35

4.5 2,45 GHz RFID systems ................................................................................................................................... 35

4.6 GBSAR systems ............................................................................................................................................... 35

4.6.1 Effective radiated power ............................................................................................................................. 35

4.6.2 Permitted range of operating frequencies ................................................................................................... 35

4.6.3 DAA threshold ............................................................................................................................................ 35

4.6.3.0 General requirements ............................................................................................................................ 35

4.6.3.1 DAA timing parameters ........................................................................................................................ 35

4.6.3.1.1 Minimum listen time ....................................................................................................................... 35

4.6.3.1.2 Minimum listen time after detection................................................................................................ 35

4.6.3.1.3 Maximum transmitter on-time ......................................................................................................... 36

4.6.3.1.4 Minimum transmitter off-time ......................................................................................................... 36

4.6.4 Antenna pattern ........................................................................................................................................... 36

ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 440 V2.2.0 (2017-09)

5 Testing for compliance with technical requirements .............................................................................. 36

5.1 Environmental conditions for testing ............................................................................................................... 36

5.2 Presentation of equipment for testing purposes ................................................................................................ 36

5.2.0 General ........................................................................................................................................................ 36

5.2.1 Choice of model for testing ........................................................................................................................ 36

5.2.2 Testing of equipment with alternative power levels ................................................................................... 37

5.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna

equipment) .................................................................................................................................................. 37

5.2.3.1 Equipment with an internal permanent or temporary antenna connector or using a dedicated test

fixture .................................................................................................................................................... 37

5.2.3.2 Equipment with a temporary antenna connector ................................................................................... 37

5.3 Mechanical and electrical design ...................................................................................................................... 37

5.3.1 General ........................................................................................................................................................ 37

5.3.2 Controls ...................................................................................................................................................... 37

5.3.3 Transmitter shut-off facility ........................................................................................................................ 37

5.3.4 Receiver mute or squelch ............................................................................................................................ 37

5.4 Auxiliary test equipment .................................................................................................................................. 38

5.5 Test power source ............................................................................................................................................. 38

5.5.0 General ........................................................................................................................................................ 38

5.5.1 External test power source .......................................................................................................................... 38

5.5.2 Internal test power source ........................................................................................................................... 38

5.6 Normal test conditions ...................................................................................................................................... 38

5.6.1 Normal temperature and humidity .............................................................................................................. 38

5.6.2 Normal test power source ........................................................................................................................... 39

5.6.2.1 Mains voltage ........................................................................................................................................ 39

5.6.2.2 Battery power sources ........................................................................................................................... 39

5.6.2.3 Other power sources .............................................................................................................................. 39

5.7 Extreme test conditions .................................................................................................................................... 39

5.7.1 Extreme temperatures ................................................................................................................................. 39

5.7.1.1 Procedure for tests at extreme temperatures .......................................................................................... 39

5.7.1.1.0 General ............................................................................................................................................ 39

5.7.1.1.1 Procedure for equipment designed for continuous operation .......................................................... 39

5.7.1.1.2 Procedure for equipment designed for intermittent operation ......................................................... 40

5.7.1.2 Extreme temperature ranges .................................................................................................................. 40

5.7.2 Extreme test source voltages ....................................................................................................................... 40

5.7.2.1 Mains voltage ........................................................................................................................................ 40

5.7.2.2 Battery power sources ........................................................................................................................... 40

5.7.2.3 Power sources using other types of batteries ......................................................................................... 40

5.7.2.4 Other power sources .............................................................................................................................. 41

5.8 General conditions ............................................................................................................................................ 41

5.8.1 Normal test signals and test modulation ..................................................................................................... 41

5.8.1.0 General .................................................................................................................................................. 41

5.8.1.1 Normal test signals for data ................................................................................................................... 41

5.8.2 Artificial antenna ........................................................................................................................................ 42

5.8.3 Test fixture .................................................................................................................................................. 42

5.8.3.0 General .................................................................................................................................................. 42

5.8.3.1 Validation of the test-fixture in the temperature chamber ..................................................................... 43

5.8.3.2 Mode of use ........................................................................................................................................... 45

5.8.4 Test sites and general arrangements for radiated measurements ................................................................ 45

5.8.5 Measuring receiver ..................................................................................................................................... 45

5.9 Interpretation of the measurement results ........................................................................................................ 45

5.9.0 General ........................................................................................................................................................ 45

5.9.1 Measurement uncertainty is greater than maximum acceptable uncertainty ............................................... 46

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 47

Annex B (normative): EU wide harmonised national radio interfaces from 1 GHz to 40 GHz ... 49

Annex C (normative): National Radio Interfaces not EU wide harmonised .................................. 50

Annex D (informative): Selection of technical parameters ................................................................. 51

ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 440 V2.2.0 (2017-09)

D.1 Introduction ............................................................................................................................................ 51

D.2 Receiver parameters ............................................................................................................................... 51

Annex E (normative): Radiated measurements .........................
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.