SIST EN IEC 60794-2-10:2023
(Main)Optical fibre cables - Part 2-10: Indoor optical fibre cables - Family specification for simplex and duplex cables (IEC 60794-2-10:2023)
Optical fibre cables - Part 2-10: Indoor optical fibre cables - Family specification for simplex and duplex cables (IEC 60794-2-10:2023)
This part of IEC 60794 is a family specification that covers simplex and duplex optical fibre
cables for indoor use. The requirements of IEC 60794-2 are applicable to cables covered by
this document.
For cables intended for installation in industrial applications specified in ISO/IEC 11801-1,
MICE specifications can be additionally required (see Clause B.2).
Lichtwellenleiterkabel - Teil 2-10: LWL-Innenkabel - Familienspezifikation für Simplex- und Duplexkabel (IEC 60794-2-10:2023)
Câbles à fibres optiques - Partie 2-10: Câbles intérieurs à fibres optiques - Spécification de famille pour les câbles simplex et duplex (IEC 60794-2-10:2023)
IEC 60794-2-10:2023 est disponible sous forme de IEC 60794-2-10:2023 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.
L'IEC 60794-2-10: 2023 couvre les câbles à fibres optiques simplex et duplex pour usage intérieur. Les exigences de l’IEC 60794-2 sont applicables aux câbles couverts par le présent document. Pour les câbles destinés à être installés dans des applications industrielles spécifiées dans l’ISO/IEC 11801-1, les spécifications MICE peuvent être exigées en plus (voir Article B.2). Cette troisième édition annule et remplace la deuxième édition parue en 2011. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- mise à jour des références normatives;
- mise à jour de toutes les désignations de catégories et de sous-catégories de fibres A1 et B1 pertinentes.
Optični kabli - 2-10. del: Notranji optični kabli - Skupinska specifikacija za simpleksne in dupleksne kable (IEC 60794-2-10:2023)
Ta del standarda IEC 60794 je rodovna specifikacija, ki zajema optične simpleksne in dupleksne kable za uporabo v notranjih prostorih. Za kable, ki jih zajema ta dokument, se uporabljajo zahteve standarda IEC 60794-2.
Za kable v industrijskem okolju, določene v standardu ISO/IEC 11801-1, se lahko dodatno zahtevajo specifikacije MICE (glej točko B.2).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 60794-2-10:2023
01-junij-2023
Optični kabli - 2-10. del: Notranji optični kabli - Skupinska specifikacija za
simpleksne in dupleksne kable (IEC 60794-2-10:2023)
Optical fibre cables - Part 2-10: Indoor optical fibre cables - Family specification for
simplex and duplex cables (IEC 60794-2-10:2023)
Lichtwellenleiterkabel - Teil 2-10: LWL-Innenkabel - Familienspezifikation für Simplex-
und Duplexkabel (IEC 60794-2-10:2023)
Câbles à fibres optiques - Partie 2-10: Câbles intérieurs à fibres optiques - Spécification
de famille pour les câbles simplex et duplex (IEC 60794-2-10:2023)
Ta slovenski standard je istoveten z: EN IEC 60794-2-10:2023
ICS:
33.180.10 (Optična) vlakna in kabli Fibres and cables
SIST EN IEC 60794-2-10:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 60794-2-10:2023
---------------------- Page: 2 ----------------------
SIST EN IEC 60794-2-10:2023
EUROPEAN STANDARD EN IEC 60794-2-10
NORME EUROPÉENNE
EUROPÄISCHE NORM April 2023
ICS 33.180.10 Supersedes EN 60794-2-10:2011
English Version
Optical fibre cables - Part 2-10: Indoor optical fibre cables -
Family specification for simplex and duplex cables
(IEC 60794-2-10:2023)
Câbles à fibres optiques - Partie 2-10: Câbles intérieurs à Lichtwellenleiterkabel - Teil 2-10: LWL-Innenkabel -
fibres optiques - Spécification de famille pour les câbles Familienspezifikation für Simplex- und Duplexkabel
simplex et duplex (IEC 60794-2-10:2023)
(IEC 60794-2-10:2023)
This European Standard was approved by CENELEC on 2023-04-14. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60794-2-10:2023 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60794-2-10:2023
EN IEC 60794-2-10:2023 (E)
European foreword
The text of document 86A/2277/FDIS, future edition 3 of IEC 60794-2-10, prepared by SC 86A "Fibres
and cables" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 60794-2-10:2023.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2024-01-14
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2026-04-14
document have to be withdrawn
This document supersedes EN 60794-2-10:2011 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
1
This document is read in conjunction with EN IEC 60794-1-1:— , EN IEC 60794-1-2:2021, EN 60794-
1-21:2015 and EN 60794-1-21:2015/A1:2020, EN IEC 60794-1-22:2018, EN IEC 60794-1-23:2019
and EN 60794-2:2017.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60794-2-10:2023 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60654-4 NOTE Approved as EN 60654-4
IEC 60721-1 NOTE Approved as EN 60721-1
IEC 60721-3-3 NOTE Approved as EN IEC 60721-3-3
IEC 60811-202 NOTE Approved as EN 60811-202
IEC 60811-501 NOTE Approved as EN 60811-501
IEC 61000-6-2 NOTE Approved as EN IEC 61000-6-2
IEC 61918 NOTE Approved as EN IEC 61918
1
To be published. Stage at time of publication: FprEN IEC 60794-1-1:2023.
2
---------------------- Page: 4 ----------------------
SIST EN IEC 60794-2-10:2023
EN IEC 60794-2-10:2023 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60304 - Standard colours for insulation for low- HD 402 S2 -
frequency cables and wires
IEC 60793-1-20 - Optical fibres - Part 1-20: Measurement EN 60793-1-20 -
methods and test procedures - Fibre
geometry
IEC 60793-1-21 - Optical fibres - Part 1-21: Measurement EN 60793-1-21 -
methods and test procedures - Coating
geometry
IEC 60793-1-40 - Optical fibres - Part 1-40: Attenuation EN IEC 60793-1-40 -
measurement methods
IEC 60793-1-44 - Optical fibres - Part 1-44: Measurement EN 60793-1-44 -
methods and test procedures - Cut-off
wavelength
IEC 60793-2 - Optical fibres - Part 2: Product EN IEC 60793-2 -
specifications - General
IEC 60793-2-10 - Optical fibres - Part 2-10: Product EN IEC 60793-2-10 -
specifications - Sectional specification for
category A1 multimode fibres
IEC 60793-2-50 - Optical fibres - Part 2-50: Product EN IEC 60793-2-50 -
specifications - Sectional specification for
class B single-mode fibres
1
IEC 60794-1-1 2022 Optical fibre cables - Part 1-1: Generic EN 60794-1-1 —
specification - General
IEC 60794-1-2 - Optical fibre cables - Part 1-2: Generic EN IEC 60794-1-2 -
specification - Basic optical cable test
procedures - General guidance
IEC 60794-1-21 - Optical fibre cables - Part 1-21: Generic EN 60794-1-21 -
specification - Basic optical cable test
procedures - Mechanical tests methods
IEC 60794-1-22 - Optical fibre cables - Part 1-22: Generic EN IEC 60794-1-22 -
specification - Basic optical cable test
procedures - Environmental test methods
3
---------------------- Page: 5 ----------------------
SIST EN IEC 60794-2-10:2023
EN IEC 60794-2-10:2023 (E)
IEC 60794-1-23 - Optical fibre cables - Part 1-23: Generic EN IEC 60794-1-23 -
specification - Basic optical cable test
procedures - Cable element test methods
IEC 60794-2 2017 Optical fibre cables - Part 2: Indoor cables EN 60794-2 2017
- Sectional specification
IEC 60811-201 - Electric and optical fibre cables - Test EN 60811-201 -
methods for non-metallic materials - Part
201: General tests - Measurement of
insulation thickness
IEC 60811-203 - Electric and optical fibre cables - Test EN 60811-203 -
methods for non-metallic materials - Part
203: General tests - Measurement of
overall dimensions
4
---------------------- Page: 6 ----------------------
SIST EN IEC 60794-2-10:2023
IEC 60794-2-10
®
Edition 3.0 2023-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Optical fibre cables –
Part 2-10: Indoor optical fibre cables – Family specification for simplex and
duplex cables
Câbles à fibres optiques –
Partie 2-10: Câbles intérieurs à fibres optiques – Spécification de famille pour
les câbles simplex et duplex
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.10 ISBN 978-2-8322-6534-5
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 60794-2-10:2023
– 2 – IEC 60794-2-10:2023 © IEC 2023
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Construction . 7
4.1 General . 7
4.2 Optical fibres and primary coating . 7
4.3 Buffer . 7
4.4 Ruggedised fibre . 8
4.5 Slotted core . 8
4.6 Tube . 8
4.7 Stranded loose tube . 8
4.8 Ribbon structure . 8
4.9 Strength and anti-buckling members . 8
4.10 Ripcord . 8
4.11 Sheath . 8
4.12 Sheath marking . 9
4.13 Identification . 9
4.14 Examples of typical cable designs . 9
5 Dimensions – Optical fibres and primary coating . 9
6 Tests . 9
6.1 General . 9
6.2 Dimensions . 9
6.3 Mechanical requirements . 9
6.3.1 General . 9
6.3.2 Tensile performance . 10
6.3.3 Crush . 10
6.3.4 Impact . 10
6.3.5 Bend . 10
6.3.6 Repeated bending . 11
6.3.7 Bending under tension . 11
6.3.8 Bending at low temperature . 11
6.3.9 Flexing . 11
6.3.10 Torsion . 11
6.3.11 Kink . 11
6.4 Environmental requirements – Temperature cycling . 11
6.5 Transmission requirements . 12
6.5.1 General . 12
6.5.2 Single-mode optical fibres . 12
6.5.3 Single-mode dispersion unshifted (B-652.B) optical fibre . 12
6.5.4 Single-mode dispersion unshifted (B-652.D) optical fibre . 13
6.5.5 Single-mode (B-657.A) optical fibre . 13
6.5.6 Single-mode (B-657.B) optical fibre . 13
6.5.7 Multimode optical fibres . 14
6.5.8 Multimode (A1-OM1 to A1-OM5) optical fibres . 14
6.6 Fire performance . 14
---------------------- Page: 8 ----------------------
SIST EN IEC 60794-2-10:2023
IEC 60794-2-10:2023 © IEC 2023 – 3 –
Annex A (informative) Examples of typical of cable designs . 15
Annex B (informative) Family specification of indoor cables – Simplex and duplex
cables . 18
B.1 Blank detail specification . 18
B.1.1 Cable description . 18
B.1.2 Cable elements . 19
B.1.3 Cable construction . 19
B.1.4 Installation and operating conditions . 20
B.1.5 Mechanical, environmental and fire performance tests . 20
B.2 Additional requirements for cables subject to the MICE environmental
classification (ISO/IEC 11801-1 and related standards) . 21
Bibliography . 22
Figure A.1 – Simplex loose non-buffered fibre cable . 15
Figure A.2 – Simplex ruggedised fibre cable . 15
Figure A.3 – Duplex loose non-buffered fibre cable . 15
Figure A.4 – Duplex ruggedised fibre cable . 16
Figure A.5 – Duplex ruggedised fibre zip cord . 16
Figure A.6 – Duplex flat cable . 16
Figure A.7 – Duplex round cable . 17
Figure A.8 – Simplex and duplex rectangular cables . 17
Table 1 – Dimensions of buffered fibres . 8
Table 2 – Method: IEC 60794-1-22, F1 . 12
Table 3 – Common single-mode optical fibre requirements . 12
Table 4 – Cabled fibre attenuation requirements for B-652.B optical fibre . 13
Table 5 – Cabled fibre attenuation requirements for B-652.D optical fibre . 13
Table 6 – Cabled fibre attenuation requirements for B-657.A optical fibre . 13
Table 7 – Cabled fibre attenuation requirements for B-657.B optical fibre . 13
Table 8 – Common multimode optical fibre requirements . 14
Table 9 – Cabled fibre attenuation requirements for A1-OM1 to A1-OM5 optical fibres . 14
Table B.1 – Cable description . 18
Table B.2 – Cable elements . 19
Table B.3 – Cable construction . 19
Table B.4 – Installation and operating conditions . 20
Table B.5 – Tests applicable . 20
---------------------- Page: 9 ----------------------
SIST EN IEC 60794-2-10:2023
– 4 – IEC 60794-2-10:2023 © IEC 2023
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL FIBRE CABLES –
Part 2-10: Indoor optical fibre cables –
Family specification for simplex and duplex cables
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 60794-2-10 has been prepared by subcommittee 86A: Fibres and cables, of IEC technical
committee 86: Fibre optics. It is an International Standard.
This third edition cancels and replaces the second edition published in 2011. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) updating of normative references;
b) updating of all relevant A1 and B1 fibre category and sub-category designations.
This International Standard is to be used in conjunction with IEC 60794‑1‑1:2022,
IEC 60794‑1‑2:2021, IEC 60794‑1‑21:2015 and IEC 60794‑1‑21:2015/AMD1:2020,
IEC 60794‑1‑22:2017, IEC 60794‑1‑23:2019 and IEC 60794‑2:2017.
---------------------- Page: 10 ----------------------
SIST EN IEC 60794-2-10:2023
IEC 60794-2-10:2023 © IEC 2023 – 5 –
The text of this International Standard is based on the following documents:
Draft Report on voting
86A/2277/FDIS 86A/2311/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts of IEC 60794 series, published under the general title Optical fibre cables, can
be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The "colour inside" logo on the cover page of this document indicates that it
contains colours which are considered to be useful for the correct understanding of its
contents. Users should therefore print this document using a colour printer.
---------------------- Page: 11 ----------------------
SIST EN IEC 60794-2-10:2023
– 6 – IEC 60794-2-10:2023 © IEC 2023
OPTICAL FIBRE CABLES –
Part 2-10: Indoor optical fibre cables –
Family specification for simplex and duplex cables
1 Scope
This part of IEC 60794 is a family specification that covers simplex and duplex optical fibre
cables for indoor use. The requirements of IEC 60794-2 are applicable to cables covered by
this document.
For cables intended for installation in industrial applications specified in ISO/IEC 11801-1,
MICE specifications can be additionally required (see Clause B.2).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60304, Standard colours for insulation for low-frequency cables and wires
IEC 60793-1-20, Optical fibres – Part 1-20: Measurement methods and test procedures – Fibre
geometry
IEC 60793-1-21, Optical fibres – Part 1-21: Measurement methods and test procedures –
Coating geometry
IEC 60793-1-40, Optical fibres – Part 1-40: Attenuation measurement methods
IEC 60793-1-44, Optical fibres – Part 1-44: Measurement methods and test procedures – Cut-
off wavelength
IEC 60793-2, Optical fibres – Part 2: Product specifications – General
IEC 60793-2-10, Optical fibres – Part 2-10: Product specifications – Sectional specification for
category A1 multimode fibres
IEC 60793-2-50, Optical fibres – Part 2-50: Product specifications – Sectional specification for
class B single-mode fibres
IEC 60794-1-1:2022, Optical fibre cables – Part 1-1: Generic specification – General
IEC 60794-1-2, Optical fibre cables – Part 1-2: Generic specification – Basic optical cable test
procedures – General guidance
IEC 60794-1-21, Optical fibre cables – Part 1-21: Generic specification – Basic optical cable
test procedures – Mechanical tests methods
IEC 60794-1-22, Optical fibre cables – Part 1-22: Generic specification – Basic optical cable
test procedures – Environmental test methods
---------------------- Page: 12 ----------------------
SIST EN IEC 60794-2-10:2023
IEC 60794-2-10:2023 © IEC 2023 – 7 –
IEC 60794-1-23, Optical fibre cables – Part 1-23: Generic specification – Basic optical cable
test procedures – Cable element test methods
IEC 60794-2:2017, Optical fibre cables – Part 2: Indoor cables – Sectional specification
IEC 60811-201, Electric and optical fibre cables – Test methods for non-metallic materials –
Part 201: General tests – Measurement of insulation thickness
IEC 60811-203, Electric and optical fibre cables – Test methods for non-metallic materials –
Part 203: General tests – Measurement of overall dimensions
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following
addresses:
• IEC Electropedia: available at https://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
4 Construction
4.1 General
In addition to the constructional requirements in IEC 60794-2, the following apply to simplex
and duplex indoor cables.
The cable shall be designed and manufactured for an expected operating lifetime of at least 15
years. In this context, the attenuation of the installed cable at the operational wavelength(s)
shall not exceed the values agreed between the customer and the supplier. The materials in
the cable shall not present a health or environmental hazard within its intended use.
There shall be no fibre splice in a delivery length unless otherwise agreed between the customer
and the supplier.
It shall be possible to identify each individual fibre throughout the length of the cable.
4.2 Optical fibres and primary coating
Multimode or single-mode optical fibres shall be used which meet the requirements of
IEC 60793-2.
4.3 Buffer
If a buffer is required, it shall consist of one or more layers of inert material. The buffer shall be
easily removable. For tight buffers, the buffer and fibre primary coating shall be removable in
one operation over a minimum length of 15 mm, depending on customer requirements. For
semi-tight buffers, the buffer shall be easily removable over a minimum length of 300 mm. For
loose buffers, the buffer shall be easily removable over a length of not less than 1,0 m.
Buffer dimensions are shown in Table 1.
---------------------- Page: 13 ----------------------
SIST EN IEC 60794-2-10:2023
– 8 – IEC 60794-2-10:2023 © IEC 2023
Table 1 – Dimensions of buffered fibres
Buffer type Nominal diameter Tolerances
mm mm
Semi-tight or loose buffer 0,3 to 1,3
± 0,05
Tight buffer 0,3 to 1,0
± 0,05
4.4 Rugg
...
SLOVENSKI STANDARD
oSIST prEN IEC 60794-2-10:2022
01-april-2022
Optični kabli - 2-10. del: Notranji optični kabli - Skupinska specifikacija za
simpleksne in dupleksne kable
Optical fibre cables - Part 2-10: Indoor optical fibre cables - Family specification for
simplex and duplex cables
Lichtwellenleiterkabel - Teil 2-10: LWL-Innenkabel - Familienspezifikation für Simplex-
und Duplexkabel
Câbles à fibres optiques - Partie 2-10: Câbles intérieurs à fibres optiques - Spécification
de famille pour les câbles simplex et duplex
Ta slovenski standard je istoveten z: prEN IEC 60794-2-10:2022
ICS:
33.180.10 (Optična) vlakna in kabli Fibres and cables
oSIST prEN IEC 60794-2-10:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN IEC 60794-2-10:2022
---------------------- Page: 2 ----------------------
oSIST prEN IEC 60794-2-10:2022
86A/2159/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 60794-2-10 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2022-01-21 2022-04-15
SUPERSEDES DOCUMENTS:
86A/2116/CD, 86A/2134A/CC
IEC SC 86A : FIBRES AND CABLES
SECRETARIAT: SECRETARY:
France Mr Laurent Gasca
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
SC 86B
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
TITLE:
Optical fibre cables - Part 2-10: Indoor optical fibre cables - Family specification for simplex
and duplex cables
PROPOSED STABILITY DATE: 2025
NOTE FROM TC/SC OFFICERS:
Copyright © 2021 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
---------------------- Page: 3 ----------------------
oSIST prEN IEC 60794-2-10:2022
IEC CDV 60794-2-10/Ed3 IEC:2022 – 2 – 86A/2159/CDV
1 CONTENTS
2 FOREWORD . 4
3 1 Scope . 6
4 2 Normative references . 6
5 3 Construction . 7
6 General . 7
7 Optical fibres and primary coating . 7
8 Buffer . 7
9 Ruggedised fibre . 8
10 Slotted core . 8
11 Tube. 8
12 Stranded loose tube . 8
13 Ribbon structure . 8
14 Strength and anti-buckling members . 8
15 Ripcord . 8
16 Sheath . 8
17 Sheath marking . 8
18 Identification. 8
19 Examples of cable constructions . 8
20 4 Dimensions – Optical fibres and primary coating . 9
21 5 Tests . 9
22 General . 9
23 Dimensions . 9
24 Mechanical requirements . 9
25 Tensile performance . 9
26 Crush . 10
27 Impact . 10
28 Bend. 10
29 Repeated bending . 10
30 Bending under tension . 10
31 Bending at low temperature . 10
32 Flexing . 10
33 Torsion . 10
34 Kink . 11
35 Environmental requirements . 11
36 Temperature cycling . 11
37 Transmission requirements . 11
38 Single-mode optical fibres . 11
39 Single-mode dispersion unshifted (B1.1) optical fibre . 12
40 Single-mode dispersion unshifted (B1.3) optical fibre . 12
41 Single-mode (B6_a) optical fibre . 12
42 Single-mode (B6_b) optical fibre . 12
43 Multimode optical fibres . 13
44 Multimode (A1a and A1b) optical fibres . 13
45 Fire performance . 13
46 Annex A (informative) Examples of some types of cable construction . 14
---------------------- Page: 4 ----------------------
oSIST prEN IEC 60794-2-10:2022
IEC CDV 60794-2-10/Ed3 IEC:2022 – 3 – 86A/2159/CDV
47 Annex B (informative) Family specification of indoor cables – simplex and duplex
48 cables . 17
49 Bibliography . 20
50
51 Figure A.1 – Simplex loose non-buffered fibre cable . 14
52 Figure A.2 – Simplex ruggedised fibre cable . 14
53 Figure A.3 – Duplex loose non-buffered fibre cable . 14
54 Figure A.4 – Duplex ruggedised fibre cable . 15
55 Figure A.5 – Duplex ruggedised fibre zip cord . 15
56 Figure A.6 – Duplex flat cable . 15
57 Figure A.7 – Duplex round cable . 16
58 Figure A.8 – Simplex and duplex rectangular cables . 16
59
60 Table 1 – Dimensions of buffered fibres . 7
61 Table 2 – Temperature cycling conditions . 11
62 Table 3 – Common single-mode optical fibre requirements . 11
63 Table 4 – Cabled fibre attenuation requirements for B1.1 optical fibre . 12
64 Table 5 – Cabled fibre attenuation requirements for B1.3 optical fibre . 12
65 Table 6 – Cabled fibre attenuation requirements for B6_a optical fibre . 12
66 Table 7 – Cabled fibre attenuation requirements for B6_b optical fibre . 13
67 Table 8 – Common multimode optical fibre requirements . 13
68 Table 9 – Cabled fibre attenuation requirements for A1a and A1b optical fibres . 13
69 Table B.1 – Cable description . 17
70 Table B.2 – Cable element . 18
71 Table B.3 – Cable construction . 18
72 Table B.4 – Installation and operating conditions . 19
73 Table B.5 – Tests applicable . 19
74
75
---------------------- Page: 5 ----------------------
oSIST prEN IEC 60794-2-10:2022
IEC CDV 60794-2-10/Ed3 IEC:2022 – 4 – 86A/2159/CDV
76 INTERNATIONAL ELECTROTECHNICAL COMMISSION
77 ___________
78
79 OPTICAL FIBRE CABLES –
80
81 Part 2-10: Indoor optical fibre cables –
82 Family specification for simplex and duplex cables
83
84
85 FOREWORD
86 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
87 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
88 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
89 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
90 Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
91 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
92 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
93 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
94 Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
95 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
96 consensus of opinion on the relevant subjects since each technical committee has representation from all
97 interested IEC National Committees.
98 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
99 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
100 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
101 misinterpretation by any end user.
102 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
103 transparently to the maximum extent possible in their national and regional publications. Any divergence between
104 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
105 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
106 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
107 services carried out by independent certification bodies.
108 6) All users should ensure that they have the latest edition of this publication.
109 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
110 members of its technical committees and IEC National Committees for any personal injury, property damage or
111 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
112 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
113 Publications.
114 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
115 indispensable for the correct application of this publication.
116 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
117 rights. IEC shall not be held responsible for identifying any or all such patent rights.
118 International Standard IEC 60794-2-10 has been prepared by sub-committee 86A: Fibres and
119 cables, of IEC technical committee 86: Fibre optics.
120 This third edition cancels and replaces the second edition published in 2011. It constitutes a
121 technical revision.
122 The main changes with respect to the previous edition are as follows:
123 – Updating of normative references
124 – Updating of all relevant A1 and B1 fibre category and sub-category designations
125 This standard is to be used in conjunction with IEC 60794-1-1, IEC 60794-1-2, IEC 60794-1-
126 21, IEC 60794-1-22, IEC 60794-1-23 and IEC 60794-2.
127
---------------------- Page: 6 ----------------------
oSIST prEN IEC 60794-2-10:2022
IEC CDV 60794-2-10/Ed3 IEC:2022 – 5 – 86A/2159/CDV
128 The text of this standard is based on the following documents:
FDIS Report on voting
86A/xxxx/FDIS 86A/xxxx/RVD
129
130 Full information on the voting for the approval of this standard can be found in the report on
131 voting indicated in the above table.
132 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
133 A list of all parts of IEC 60794 series, published under the general title Optical fibre cables, can
134 be found on the IEC website.
135 The committee has decided that the contents of this publication will remain unchanged until the
136 stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to
137 the specific publication. At this date, the publication will be
138 • reconfirmed,
139 • withdrawn,
140 • replaced by a revised edition, or
141 • amended.
142
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates that it
contains colours which are considered to be useful for the correct understanding of its
contents. Users should therefore print this document using a colour printer.
143
144
145
---------------------- Page: 7 ----------------------
oSIST prEN IEC 60794-2-10:2022
IEC CDV 60794-2-10/Ed3 IEC:2022 – 6 – 86A/2159/CDV
146 OPTICAL FIBRE CABLES –
147
148 Part 2-10: Indoor optical fibre cables –
149 Family specification for simplex and duplex cables
150
151
152
153 1 Scope
154 This part of IEC 60794 is a family specification that covers simplex and duplex optical fibre
155 cables for indoor use except for cables used in terminated assemblies specified by IEC 60794-
156 2-50. The requirements of the Sectional specification IEC 60794-2 are applicable to cables
157 covered by this standard.
158 Cables intended for installation in industrial applications specified in ISO/IEC 11801-1, MICE
159 specifications may be additionally required (see Annex B.2).
160 2 Normative references
161 The following referenced documents are indispensable for the application of this document. For
162 dated references, only the edition cited applies. For undated references, the latest edition of
163 the referenced document (including any amendments) applies.
164 IEC 60304, Standard colours for insulation for low-frequency cables and wires
165 IEC 60793-1-20, Optical fibres – Part 1-20: Measurement methods and test procedures – Fibre
166 geometry
167 IEC 60793-1-21, Optical fibres – Part 1-21: Measurement methods and test procedures –
168 Coating geometry
169 IEC 60793-1-40, Optical fibres – Part 1-40: Measurement methods and test procedures –
170 Attenuation
171 IEC 60793-1-44, Optical fibres – Part 1-44: Measurement methods and test procedures – Cut-
172 off wavelength
173 IEC 60793-2, Optical fibres – Part 2: Product specifications – General
174 IEC 60793-2-10, Optical fibres – Part 2-10: Product specifications – Sectional specification for
175 category A1 multimode fibres
176 IEC 60793-2-50, Optical fibres – Part 2-50: Product specifications – Sectional specification for
177 class B single-mode fibres
178 IEC 60794-1-1, Optical fibre cables – Part 1-1: Generic specification – General
179 IEC 60794-1-2, Optical fibre cables – Part 1-2: Generic specification – Basic optical cable test
180 procedures
181 IEC 60794-1-21, Optical fibre cables – Part 1-21: Generic specification – Basic optical cable
182 test procedures – Mechanical tests methods
---------------------- Page: 8 ----------------------
oSIST prEN IEC 60794-2-10:2022
IEC CDV 60794-2-10/Ed3 IEC:2022 – 7 – 86A/2159/CDV
183 IEC 60794-1-22, Optical fibre cables – Part 1-22: Generic specification – Basic optical cable
184 test procedures – Environmental tests methods
185 IEC 60794-1-23, Optical fibre cables – Part 1-22: Generic specification – Basic optical cable
186 test procedures - Cable element test methods
187 IEC 60794-2, Optical fibre cables – Part 2: Indoor cables – Sectional specification
188 IEC 60811-1-1, Common test methods for insulating and sheathing materials of electric cables
189 – Part 1-1: Methods for general application – Measurement of thickness and overall dimensions
190 – Tests for determining the mechanical properties
191 3 Construction
192 General
193 In addition to the constructional requirements in IEC 60794-2, the following apply to simplex
194 and duplex indoor cables.
195 The cable shall be designed and manufactured for an expected operating lifetime of at least 15
196 years. In this context, the attenuation of the installed cable at the operational wavelength(s)
197 shall not exceed values agreed between the customer and the supplier. The materials in the
198 cable shall not present a health or environmental hazard within its intended use.
199 There shall be no fibre splice in a delivery length unless otherwise agreed by the customer and
200 the supplier.
201 It shall be possible to identify each individual fibre throughout the length of the cable.
202 Optical fibres and primary coating
203 Multimode or single-mode optical fibres shall be used which meet the requirements of
204 IEC 60793-2.
205 Buffer
206 If a buffer is required, it shall consist of one or more layers of inert material. The buffer shall be
207 easily removable. For tight buffers, the buffer and fibre primary coating shall be removable in
208 one operation over a minimum length of 15 mm, depending on customer requirements. For
2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.