SIST EN IEC 60794-1-130:2026
(Main)Optical fibre cables - Part 1-130: Generic specification - Basic optical cable test procedures - Mechanical tests methods - Coefficient of dynamic friction between cables, Methods E30 (IEC 60794-1-130:2025)
Optical fibre cables - Part 1-130: Generic specification - Basic optical cable test procedures - Mechanical tests methods - Coefficient of dynamic friction between cables, Methods E30 (IEC 60794-1-130:2025)
IEC 60794-1-130:2025 describes test procedures to evaluate the coefficient of dynamic friction of the sheathing material of a cable when pulled over or between other cables. Methods E30A and E30B evaluate the coefficient of friction between cables for when either a cable is pulled over the top of other cables (drum test) or when pulling a cable between other cables of the same shape (flat plate test). This document applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors. Throughout the document, wording "optical cable" can also include optical fibre units and microduct fibre units.
This first edition cancels and replaces Method E24 of the first edition of IEC 60794‑1‑21 published in 2015, Amendment 1:2020. This edition constitutes a technical revision.
Lichtwellenleiterkabel - Teil 1-130: Fachgrundspezifikation - Grundlegende Prüfverfahren für Lichtwellenleiterkabel - Mechanische Prüfverfahren - Gleitreibungskoeffizient zwischen Kabeln, Verfahren E30 (IEC 60794-1-130:2025)
Câbles à fibres optiques - Partie 1-130: Spécification générique - Procédures fondamentales d’essais des câbles optiques - Méthodes d’essais mécaniques - Coefficient de frottement dynamique entre les câbles, Méthodes E30 (IEC 60794-1-130:2025)
IEC 60794-1-130:2025 décrit les procédures d'essais en vue d'évaluer le coefficient de frottement dynamique du matériau de la gaine du câble lorsqu'il est tiré sur ou entre d'autres câbles. Les Méthodes E30A et E30B évaluent le coefficient de frottement entre les câbles lorsqu'un câble est tiré par-dessus d'autres câbles (essai au touret) ou lors de la traction d'un câble entre d'autres câbles de même forme (essai à la plaque plane).
Le présent document s’applique aux câbles à fibres optiques destinés à être utilisés dans les équipements de télécommunication et les dispositifs qui utilisent des techniques analogues, ainsi qu'aux câbles constitués de fibres optiques d'une part et de conducteurs électriques d'autre part.
Dans le présent document, l'expression "câble optique" peut également englober les assemblages de fibres optiques, les assemblages de fibres en microconduits.
Cette première édition annule et remplace la Méthode E24 de la première édition de l'IEC 60794‑1‑21 publiée en 2015, Amendement 1:2020. Cette édition constitue une révision technique.
Optični kabli - 1-130. del: Splošna specifikacija - Osnovni preskusni postopki za optične kable - Mehanske preskusne metode - Koeficient dinamičnega trenja med kabli, metode E30 (IEC 60794-1-130:2025)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2026
Nadomešča:
SIST EN 60794-1-21:2015
SIST EN 60794-1-21:2015/A1:2020
Optični kabli - 1-130. del: Splošna specifikacija - Osnovni preskusni postopki za
optične kable - Mehanske preskusne metode - Koeficient dinamičnega trenja med
kabli, metode E30 (IEC 60794-1-130:2025)
Optical fibre cables - Part 1-130: Generic specification - Basic optical cable test
procedures - Mechanical tests methods - Coefficient of dynamic friction between cables,
Methods E30 (IEC 60794-1-130:2025)
Lichtwellenleiterkabel - Teil 1-130: Fachgrundspezifikation - Grundlegende Prüfverfahren
für Lichtwellenleiterkabel - Mechanische Prüfverfahren - Gleitreibungskoeffizient
zwischen Kabeln, Verfahren E30 (IEC 60794-1-130:2025)
Câbles à fibres optiques - Partie 1-130: Spécification générique - Procédures
fondamentales d’essais des câbles optiques - Méthodes d’essais mécaniques -
Coefficient de frottement dynamique entre les câbles, Méthodes E30 (IEC 60794-1-
130:2025)
Ta slovenski standard je istoveten z: EN IEC 60794-1-130:2025
ICS:
19.060 Mehansko preskušanje Mechanical testing
33.180.10 (Optična) vlakna in kabli Fibres and cables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60794-1-130
NORME EUROPÉENNE
EUROPÄISCHE NORM November 2025
ICS 33.180.10 Supersedes EN 60794-1-21:2015 (partially); EN 60794-1-
21:2015/A1:2020 (partially)
English Version
Optical fibre cables - Part 1-130: Generic specification - Basic
optical cable test procedures - Mechanical tests methods -
Coefficient of friction between cables, Methods E30
(IEC 60794-1-130:2025)
Câbles à fibres optiques - Partie 1-130: Spécification Lichtwellenleiterkabel - Teil 1-130: Fachgrundspezifikation -
générique - Procédures fondamentales d'essais des câbles Grundlegende Prüfverfahren für Lichtwellenleiterkabel -
optiques - Méthodes d'essais mécaniques - Coefficient de Mechanische Prüfverfahren - Gleitreibungskoeffizient
frottement entre les câbles, Méthodes E30 zwischen Kabeln, Verfahren E30
(IEC 60794-1-130:2025) (IEC 60794-1-130:2025)
This European Standard was approved by CENELEC on 2025-11-05. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60794-1-130:2025 E
European foreword
The text of document 86A/2602/FDIS, future edition 1 of IEC 60794-1-130, prepared by SC 86A
"Fibres and cables" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 60794-1-130:2025.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2026-11-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2028-11-30
document have to be withdrawn
This document partially supersedes EN 60794-1-21:2015 and all of its amendments and corrigenda (if
any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60794-1-130:2025 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60794-1-21 NOTE Approved as EN 60794-1-21
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60794-1-2 - Optical fibre cables - Part 1-2: Generic EN IEC 60794-1-2 -
specification - Basic optical cable test
procedures - General guidance
IEC 60794-1-130 ®
Edition 1.0 2025-10
INTERNATIONAL
STANDARD
Optical fibre cables -
Part 1-130: Generic specification - Basic optical cable test procedures -
Mechanical tests methods - Coefficient of friction between cables, Methods E30
ICS 33.180.10 ISBN 978-2-8327-0721-0
IEC 60794-1-130:2025-10(en)
IEC 60794-1-130:2025 © IEC 2025
CONTENTS
FOREWORD . 2
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 General requirements. 4
5 Method E30A: Coefficient of friction between cables (sheave test) . 4
5.1 Object . 4
5.2 Sample . 5
5.3 Apparatus . 5
5.4 Procedure . 6
5.5 Requirement . 7
5.6 Details to be specified . 7
5.7 Details to be reported . 7
6 Method E30B: Coefficient of friction between cables (flat plate test) . 8
6.1 Object . 8
6.2 Sample . 8
6.3 Apparatus . 8
6.4 Procedure . 8
6.5 Details to be specified . 9
6.6 Details to be reported . 9
Bibliography . 10
Figure 1 – Coefficient of friction test apparatus (sheave test) . 6
Figure 2 – Coefficient of friction test apparatus (flat plate test) . 8
IEC 60794-1-130:2025 © IEC 2025
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
Optical fibre cables -
Part 1-130: Generic specification -
Basic optical cable test procedures - Mechanical test methods -
Coefficient of friction between cables, Methods E30
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 60794-1-130 has been prepared by subcommittee 86A: Fibres and cables, of IEC technical
committee 86: Fibre optics. It is an International Standard.
This first edition cancels and replaces Method E24 of the first edition of IEC 60794-1-21
published in 2015, Amendment 1:2020. This edition constitutes a technical revision.
The text of this International Standard is based on the following documents:
Draft Report on voting
86A/2602/FDIS 86A/2618/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
IEC 60794-1-130:2025 © IEC 2025
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts in the IEC 60794 series, publi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.