SIST EN 1218-3:2002
(Main)Safety of woodworking machines - Tenoning machines - Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers
Safety of woodworking machines - Tenoning machines - Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers
This European Standard sets out the requirements and/or the measures to remove the hazards and limit the risks on hand fed tenoning machines with sliding table for cutting structural timbers, hereinafter referred to as "machines".
This European Standard does not apply to :
3 machines where the tenon is produced by means of milling tools;
3 machines designed for a tool spindle speed exceeding 6000 min-1;
3 machines where the cuts are made on both ends of the workpiece during one cycle;
3 combined machines used for tenoning (see EN 940 : 1997);
3 the tenoning attachment on a vertical spindle moulding machine (see EN 848-1 : 1998).
This European Standard covers the hazards relevant to this machine as listed in clause 4.
For Computer Numerically Controlled (CNC) machines this European Standard does not cover hazards related to Electro-Magnetic Compatibility (EMC).
This European Standard is primarily directed to machines which are manufactured after the date of issue of this European Standard.
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen - Teil 3: Abbundmaschinen mit von Hand bewegtem Schiebetisch
Diese Europäische Norm beschreibt die Anforderungen und/oder Maßnahmen für die Beseitigung von Gefähr-dun-gen und zur Begrenzung der Risiken an Abbundmaschinen mit Handvorschub des Schiebetisches - im Folgenden als ?Maschinen" bezeichnet, die zum Schneiden von Massivholz bestimmt sind.
Diese Europäische Norm gilt nicht für:
3 Maschinen, bei denen Schlitz/Zapfen mit Fräswerkzeugen hergestellt wird;
3 Maschinen, bei denen die konstruktiv vorgesehene Drehzahl irgend einer Werkzeugspindel 6000 min-1 übersteigt;
3 Maschinen, bei denen die Schnitte in einem Durchlauf an beiden Enden des Werkstücks durchgeführt werden;
3 kombinierte Maschinen, die zum Zapfenschneiden/Schlitzen verwendet werden (siehe EN 940:1997);
3 die Zapfenschneideinrichtung für Tischfräsmaschinen (siehe EN 848-1:1998).
Diese Europäische Norm behandelt die von der Maschine ausgehenden Gefährdungen, wie sie in Abschnitt 4 aufgelistet sind.
Diese Europäische Norm behandelt bei CNC-Maschinen nicht die Gefährdungen im Zusammenhang mit der elek-tromagnetischen Verträglichkeit (EMV).
Diese Europäische Norm gilt in erster Linie für Maschinen, die nach dem Ausgabedatum dieser Europäischen Norm hergestellt werden.
Sécurité des machines a bois - Tenonneuses - Partie 3: Machines a avance manuelle et a table roulante pour la coupe des éléments de charpente de toit en bois
La présente Norme européenne spécifie les prescriptions et/ou les mesures qui doivent etre prises pour éliminer les phénomenes dangereux et limiter les risques sur les machines a avance manuelle et a table roulante pour la coupe des éléments de charpente de toit en bois, ci-apres désignées par le terme "machines".
La présente Norme européenne ne s'applique pas :
3 aux machines sur lesquelles le tenon est réalisé a l'aide d'outils a fraiser ;
3 aux machines conçues pour une vitesse d'une broche porte-outil supérieure a 6 000 min-1 ;
3 aux machines sur lesquelles les coupes sont effectuées aux deux extrémités de la piece durant un seul cycle ;
3 aux machines combinées utilisées pour le tenonnage (voir l'EN 940:1997) ;
3 aux accessoires de tenonnage installés sur une toupie verticale (voir l'EN 848-1:1998).
La présente norme couvre les phénomenes dangereux applicables a ces machines dont une liste est donnée a l'article 4.
Pour les machines a commande numérique (CN), la présente norme européenne ne traite pas les phénomenes dangereux liés a la comptabilité électromagnétique (CEM).
La présente Norme européenne est applicable avant tout aux machines fabriquées apres la date de publication de la présente Norme européenne.
Varnost lesnoobdelovalnih strojev - Stroji za izdelovanje čepov in utorov - 3. del: Stroji za razrez lesa z ročno podajalno mizo
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1218-3:2002
01-november-2002
9DUQRVWOHVQRREGHORYDOQLKVWURMHY6WURML]DL]GHORYDQMHþHSRYLQXWRURYGHO
6WURML]DUD]UH]OHVD]URþQRSRGDMDOQRPL]R
Safety of woodworking machines - Tenoning machines - Part 3: Hand fed tenoning
machines with sliding table for cutting structural timbers
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen -
Teil 3: Abbundmaschinen mit von Hand bewegtem Schiebetisch
Sécurité des machines a bois - Tenonneuses - Partie 3: Machines a avance manuelle et
a table roulante pour la coupe des éléments de charpente de toit en bois
Ta slovenski standard je istoveten z: EN 1218-3:2001
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1218-3:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 1218-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2001
ICS 79.120.10
English version
Safety of woodworking machines - Tenoning machines - Part 3:
Hand fed tenoning machines with sliding table for cutting
structural timbers
Sécurité des machines à bois - Tenonneuses - Partie 3: Sicherheit von Holzbearbeitungsmaschinen -
Machines à avance manuelle et à table roulante pour la Zapfenschneid- und Schlitzmaschinen - Teil 3:
coupe des éléments de charpente de toit en bois Abbundmaschinen mit von Hand bewegtem Schiebetisch
This European Standard was approved by CEN on 30 September 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1218-3:2001 E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 1218-3:2001 (E)
Contents
Foreword.3
0 Introduction .4
1 Scope .4
2 Normative references .4
3 Terms and definitions.6
3.1 Terms .6
3.2 Definitions.6
4 List of hazards.9
5 Safety requirements and/or measures .11
5.1 Controls .11
5.2 Protection against mechanical hazards .14
5.3 Protection against non-mechanical hazards .23
6 Information for use .26
6.1 Warning devices.26
6.2 Marking .26
6.3 Instruction handbook .26
Annex A (normative) Transportable machine stability test .28
A.1 Tilting Test.28
A.2 Displacement test .28
Annex B (normative) Saw spindle dimensional tolerances .30
Annex C (normative) Riving knife lateral stability test.31
Annex D (normative) Operating conditions for noise emission measurement .32
D.1 General.32
D.2 Noise measurements.32
Annex E (informative) Safe working practice .37
E.1 General.37
E.2 Sawblades.37
E.3 Workpiece.38
E.4 Sliding table.38
E.5 Noise .38
E.6 Dust .38
Annex ZA (informative) Relationship of this document with EC Directives.39
Bibliography .40
2
---------------------- Page: 3 ----------------------
EN 1218-3:2001 (E)
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 142 "Woodworking machines -
Safety", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by April 2002, and conflicting national standards shall be withdrawn at the latest by
April 2002.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative annex ZA, which is an integral part of this document.
Organisations contributing to the preparation of this European Standard include European Committee of
Woodworking Machinery Manufacturers Association "EUMABOIS".
The annexes A, B, C and D are normative and annexes E and ZA are informative.
This standard includes a Bibliography.
The European Standards produced by CEN/TC 142 are particular to woodworking machines and complement the
relevant A and B Standards on the subject of general safety (see introduction of EN 292-1 : 1991 for a description
of A, B and C standards).
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,
Switzerland and the United Kingdom.
3
---------------------- Page: 4 ----------------------
EN 1218-3:2001 (E)
0 Introduction
This European Standard has been prepared to be a harmonised standard to provide one means of conforming to
the essential safety requirements of the Machinery Directive, and associated EFTA regulations. This European
Standard is a type "C“ standard as defined in EN 292-1 : 1991.
The extent to which hazards are covered is indicated in the scope of this European Standard.
The requirements of this European Standard concern designers, manufacturers, suppliers and importers of hand
fed tenoning machines with sliding table for cutting structural timbers.
This European Standard also includes information to be provided by the manufacturer to the user.
Common requirements for tooling are given in EN 847-1 : 1997.
1 Scope
This European Standard sets out the requirements and/or the measures to remove the hazards and limit the risks
on hand fed tenoning machines with sliding table for cutting structural timbers, hereinafter referred to as
"machines".
This European Standard does not apply to :
machines where the tenon is produced by means of milling tools;
-1
machines designed for a tool spindle speed exceeding 6000 min ;
machines where the cuts are made on both ends of the workpiece during one cycle;
combined machines used for tenoning (see EN 940 : 1997);
the tenoning attachment on a vertical spindle moulding machine (see EN 848-1 : 1998).
This European Standard covers the hazards relevant to this machine as listed in clause 4.
For Computer Numerically Controlled (CNC) machines this European Standard does not cover hazards related to
Electro-Magnetic Compatibility (EMC).
This European Standard is primarily directed to machines which are manufactured after the date of issue of this
European Standard.
2 Normative references
This European Standard incorporates by dated or undated reference provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 292-1 : 1991 Safety of machinery - Basic concepts, general principles for design - Part 1 :
Basic terminology and methodology.
EN 292-2 : 1991 Safety of machinery - Basic concepts, general principles for design - Part 2 :
EN 292-2/A1 : 1995 Technical principles and specifications.
EN 418 : 1992 Safety of machines - Emergency stop equipment - Functional aspects –
Principles for design.
EN 847-1 : 1997 Tools for woodworking - Safety requirements – Part 1 : Milling tools and circular
sawblades.
4
---------------------- Page: 5 ----------------------
EN 1218-3:2001 (E)
EN 954-1 : 1996 Safety of machinery - Safety related parts of control systems - Part 1 : General
principles for design.
EN 982 : 1996 Safety requirements for fluid power systems and components – Hydraulics.
EN 983 : 1996 Safety requirements for fluid power systems and components – Pneumatics.
EN 1088 : 1995 Safety of machinery - Interlocking devices associated with guards – Principles
for design and selection.
EN 60204-1 : 1992 Safety of machinery - Electrical equipment of machines - Part 1 : General
requirements (IEC 204-1 : 1992, modified).
EN 60529 : 1991 Degree of protection provided by enclosures (IP code) (IEC 60529 : 1989).
EN 60825-1 : 1994 Safety of laser products - Part 1 : Equipment classification, requirements and
users guide (IEC 60825-1 : 1993).
EN 60947-4-1 : 1992 Low voltage switchgear and control gear - Part 4 : Contactors and motor starters
- Section 1 : Electromechanical contactors and motor starters
(IEC 60947-4-1 : 1990).
EN 60947-5-1 : 1997 Low voltage switchgear and control gear - Part 5 : Control circuit devices and
switching elements – Section 1 : Electromechanical control circuit devices
(IEC 60947-5-1 : 1997).
EN ISO 3743-1 : 1995 Acoustics – Determination of sound power levels of noise sources - Engineering
methods for small, moveable sources in reverberant fields - Part 1 : Comparison
method for hard wall test rooms (ISO 3743-1 : 1994).
EN ISO 3743-2 : 1996 Acoustics - Determination of sound power levels of noise sources - Engineering
methods for small, moveable sources in reverberant fields - Part 2 : Method for
special reverberation test rooms (ISO 3743-2 : 1994).
EN ISO 3744 : 1995 Acoustics - Determination of sound power levels of noise sources using sound
pressure engineering methods in an essentially free field over a reflecting plane
(ISO 3744 : 1994).
EN ISO 3746 : 1995 Acoustics – Determination of sound power levels of noise sources using sound
pressure – Survey method employing an enveloping measurement surface over
a reflecting plane (ISO 3746 : 1995).
EN ISO 4871 : 1996 Acoustics – Determination and verification of noise emission values of
machinery and equipment (ISO 4871 : 1996).
EN ISO 9614-1 : 1995 Acoustics - Determination of sound power levels of noise sources using sound
intensity - Part 1 : Measurement at discrete points (ISO 9614-1 : 1993).
EN ISO 11202 : 1995 Acoustics - Noise emitted by machinery and equipment – Measurement method
of emission sound pressure levels at the workstation and at other specified
positions survey method in situ (ISO 11202 : 1995).
EN ISO 11204 : 1995 Acoustics - Noise emitted by machinery and equipment - Measurement of
emission sound pressure levels at the workstation and at other specified
positions - Method requiring environmental corrections (ISO 11204 : 1995).
EN ISO 11688-1 : 1998 Acoustics - Recommended practice for the design of low noise machinery and
equipment - Part 1 : Planning (ISO/TR 11688-1 : 1995).
ISO 286-2 : 1988 ISO system of limits and fits - Part 2 : Tables of standard tolerance grades and
limit deviations for holes and shafts.
5
---------------------- Page: 6 ----------------------
EN 1218-3:2001 (E)
ISO 3745 : 1977 Acoustics - Determination of sound power levels of noise sources - Precision
methods for anechoic and semi-anechoic rooms.
HD 21.1 S3 : 1997 Polyvinyl chloride insulated cables of rated voltages up to and including
450/750v - Part 1 : General requirements.
HD 22.1 S3 : 1997 Rubber insulated cables of rated voltages up to and including 450/750v - Part 1
: General requirements.
HD 22.4 S3 : 1995 Rubber insulated cables of rated voltages up to and including 450/750 V - Part 4
+ A1 : 1999 : Cords and flexible cables (IEC 60245-4 : 1994, modified).
3 Terms and definitions
For the purposes of this European Standard the following terms and definitions apply.
3.1 Terms
The main parts of the machine and their terminology are illustrated in Figure 1.
Key 1 Main sawblade
2 Horizontal sawblades
3 Vertical sawblades
4 Controls
5 Sliding table guide
6 Sliding table
7 Workpiece clamping bridge
NOTE This figure is intended only to illustrate terms. For clarity not all necessary guards are shown
Figure 1 — Terminology
3.2 Definitions
3.2.1
hand fed tenoning machine with sliding table for cutting structural timbers
machine designed for the production of cuts, for jointing structural timbers, on one end of a workpiece during one
cycle. The cuts are made by means of sawblade(s) mounted on one or more spindles (see Figure 1)
3.2.2
cuts for jointing structural timber
machined projections including tenons on the end of a workpiece to facilitate the joining of workpieces (see Figure
2)
6
---------------------- Page: 7 ----------------------
EN 1218-3:2001 (E)
Figure 2 — Examples of saw cuts for joining structural timber
3.2.3
hand feed
manual holding and/or manual guiding of the workpiece (or of a machine element incorporating a tool). Hand feed
includes the use of a hand operated carriage on which the workpiece is placed manually or clamped (and the use
of a demountable power feed unit)
NOTE The words in brackets are not applicable to this machine.
3.2.4
ejection
unexpected movement of the workpiece, parts of it or part of the machine from the machine during processing
3.2.5
run-up time
time elapsed from the actuation of the start control device until the spindle reaches the intended speed
3.2.6
run-down time
time elapsed from the actuation of the stop control device up to spindle standstill
3.2.7
transportable machine
machine, which is located on the floor, stationary during use and equipped with a device, normally wheels, which
allow it to be moved between locations
3.2.8
cutting against the feed
when the relative direction of the tool to the workpiece is as illustrated in Figure 3
7
---------------------- Page: 8 ----------------------
EN 1218-3:2001 (E)
Key 1 Fixed sawblade
2 Sawblade
3Workpiece
4 Fixed workpiece
5 Feed direction
Figure 3 — Rotational direction of the tool relative to the workpiece feed during cutting against the feed
3.2.9
climb cutting
when the relative direction of the tool to the workpiece is as illustrated in Figure 4
Key 1 Fixed sawblade
2 Sawblade
3Workpiece
4 Fixed workpiece
5 Feed direction
Figure 4 — Rotational direction of the tool relative to the workpiece feed during climb cutting
3.2.10
machine actuator
power mechanism used to effect motion of the machine
3.2.11
confirmation
statements, sales literature, leaflets or other, where a manufacturer (supplier) declares either the characteristics of
e.g. a material or product or the compliance of the material or product to a relevant standard
8
---------------------- Page: 9 ----------------------
EN 1218-3:2001 (E)
4 List of hazards
This European Standard deals with hazards listed and relevant to the machines as defined in the scope :
for significant hazards by defining safety requirements and/or measures or by reference to relevant type B
standards;
for hazards which are not significant e.g. general, minor or secondary hazards by reference to relevant type
A or B standards, especially EN 292-1 : 1991 and EN 292-2 : 1991/A1 : 1995.
These hazards are listed in Table 1 in accordance with annex A of EN 292-2 : 1991/A1 : 1995.
9
---------------------- Page: 10 ----------------------
EN 1218-3:2001 (E)
Table 1 — List of hazards
Number Hazard Relevant subclause of this
European Standard
1 Mechanical hazards (caused for example by :
- shape
- relative location
- mass and stability (potential energy of elements)
- mass and velocity (kinetic energy of elements)
- inadequacy of the mechanical strength.
Accumulation of Potential energy by :
- elastic elements (springs), or
- liquids or gases under pressure, or
- vacuum.
of the machine parts or workpieces)
1.1 Crushing hazard 5.2.1, 5.2.7, 5.2.8
1.2 Shearing hazard 5.2.7, 5.2.8
1.3 Cutting or severing hazard 5.2.2, 5.2.3, 5.2.4, 5.2.7,
5.2.8
1.4 Entanglement hazard 5.2.3, 5.2.4, 5.2.6, 5.2.7
1.5 Drawing-in or trapping hazard 5.2.7, 5.2.8
1.6 Impact hazard Not relevant
1.7 Stabbing or puncture hazard Not relevant
1.8 Friction or abrasion hazard Not relevant
1.9 High pressure fluid injection hazard 5.3.7, 5.3.8
1.10 Ejection of parts (of machinery and processed 5.2.2, 5.2.3, 5.2.5, 5.2.6,
materials/workpieces) 5.2.8
1.11 Loss of stability (of machinery and machine parts) 5.2.1
1.12 Slip, trip and fall hazards in relationship with machinery (because of Not relevant
their mechanical nature)
2 Electrical hazards, caused for example by :
2.1 Electrical contact (direct or indirect) 5.3.4, 5.3.16, 5.3.17
2.2 Electrostatic phenomena Not relevant
2.3 Thermal radiation or other phenomena such as ejection of molten Not relevant
particles, and chemical effects from short circuits, overloads, etc.
2.4 External influences on electrical equipment 5.1.1, 5.3.4, 5.3.12
3 Thermal hazards, resulting in :
3.1 Burns and scalds, by a possible contact of persons, by flames or Not relevant
explosions and also by the radiation of heat sources
3.2 Health damaging effects by hot or cold work environment Not relevant
4 Hazards generated by noise, resulting in :
4.1 hearing losses (deafness), other physiological disorders (e.g. loss 5.3.2
of balance, loss of awareness)
4.2 interference with speech communication, acoustic signals, etc. 5.3.2
5 Hazards generated by vibration (resulting in a variety of Not relevant
neurological and vascular disorders)
6 Hazards generated by radiation, especially by :
6.1 electrical arcs Not relevant
6.2 Lasers 5.3.13, 6.3
6.3 Ionising radiation sources Not relevant
6.4 Machines making use of high frequency electro magnetic fields Not relevant
(continued)
10
---------------------- Page: 11 ----------------------
EN 1218-3:2001 (E)
Table 1 — List of hazards (concluded)
Number Hazard Relevant subclause of this
European Standard
7 Hazards generated by materials and substances processed, used
or exhausted by machinery for example :
7.1 Hazards resulting from contact with or inhalation of harmful fluids, 5.3.3
gases, mists, fumes and dusts
7.2 fire and explosion hazard 5.3.1, 5.3.3, Annex E
7.3 Biological and microbiological (viral or bacterial) hazards Not relevant
8 Hazards generated by neglecting ergonomic principles in machine
design (mismatch of machinery with human characteristics and
abilities) caused for example by :
8.1 unhealthy postures or excessive efforts 5.1.2, 6.3
8.2 inadequate consideration of human hand/arm or foot/leg anatomy 5.1.2, 6.3
8.3 neglected use of personal protection equipment 6.3
8.4 inadequate area lighting Annex E
8.5 mental overload or underload, stress, etc. Not relevant
8.6 human error 6.3
9 Hazard combinations Not relevant
10 Hazards caused by failure of energy supply, breaking down of
machinery parts and other functional disorders, for example :
10.1 failure of energy supply (of energy and/or control circuits) 5.1.6, 5.2.5
10.2 unexpected ejection of machine parts or fluids 5.3.16
10.3 failure, malfunction of control system (unexpected start-up, 5.1.1
unexpected overrun).
10.4 errors of fitting 5.2.3, 6.3
10.5 overturn, unexpected loss of machine stability 5.2.1
11 Hazards caused by (temporary) missing and/or incorrectly
positioned safety related measures/means, for example :
11.1 all kinds of guards 5.2.7
11.2 all kinds of safety related (protection) devices 5.1.1, 5.2.7
11.3 starting and stopping devices 5.1.2, 5.1.3, 5.1.4
11.4 safety signs and signals 6.2
11.5 all kinds of information or warning devices 6.2, 6.3
11.6 energy supply disconnecting devices 5.3.16
11.7 emergency devices 5.1.5
11.8 feeding/removal means for workpieces 5.2.5, 5.2.6
11.9 essential equipment and accessories for safe adjusting and/or 5.3.17
maintaining
11.10 equipment evacuating gases, etc. 5.3.3, 6.3
5 Safety requirements and/or measures
For guidance in connection with risk reduction by design, see clause 3 of EN 292-2 : 1991/A1 : 1995 and in
addition :
5.1 Controls
5.1.1 Safety and reliability of control systems
For the purposes of this European Standard a safety related control system is one from and including the initial
manual control or position detector to the point of input to the final actuator or element e.g. motor. The safety
related control systems of this machine (see EN 954-1 : 1996) are those for :
starting (see 5.1.3);
normal stopping (see 5.1.4);
emergency stop (see 5.1.5);
the braking system (see 5.2.4);
11
---------------------- Page: 12 ----------------------
EN 1218-3:2001 (E)
interlocking (see 5.2.7);
interlocking with guard locking (see 5.2.7);
powered clamping (where provided) (see 5.2.8).
Unless otherwise stated in this European Standard these control systems shall, as a minimum, be designed and
constructed in accordance with category 1 as defined in EN 954-1 : 1996.
For the purposes of this European Standard "well tried components and principles" means :
a) electrical components if they comply with relevant standards including the following as :
1) EN 60947-5-1 : 1997 (section 3) for control switches with positive opening operation used as
mechanical actuated position detectors for interlocking guards and for relays used in auxiliary circuits;
2) EN 60947-4-1 : 1992 for electromechanical contactors and motor-starters used in main circuits;
3) HD 22.1 S3 : 1997 for rubber-insulated cables;
4) HD 21.1 S3 : 1997 for polyvinyl chloride cable if this cable is additionally protected against mechanical
damage by positioning (e.g. inside frames).
b) electrical principles if they comply with the first four measures listed in 9.4.2.1 of EN 60204-1: 1992. The
circuits shall be either “hardwired”, or if electronic components are used in safety related control systems
“well tried” is fulfilled if they are in accordance with 9.4.2.2 (i.e. redundancy with cross-monitoring) or
9.4.2.3 (i.e. diversity) of EN 60204-1: 1992;
c) mechanical components if, for example they operate in the positive mode in accordance with the
description given in 3.5 of EN 292-2 : 1991/A1 : 1995;
d) mechanically actuated position detectors for guards if they are actuated in the positive mode and their
arrangement/fastening and the cam design/mounting comply with 5.2 and 5.3 of EN 1088 : 1995;
e) interlocking devices with guard locking if they satisfy the requirements of 5.2.7.1;
f) pneumatic and hydraulic components and systems if they comply with EN 983 : 1996 and EN 982 : 1996
respectively.
Time delay devices used in hardwired safety related control circuits may be of category B in accordance with the
requirements of EN 954-1 : 1996 if the time delay device is designed for at least one million actuations.
Verification : By checking the relevant drawings and/or circuit diagrams and inspection on the machine. For
electrical components by requiring confirmation from the manufacturer of the component which declares conformity
with the relevant standards.
5.1.2 Position of controls
The main control devices of the machine for starting the saw spindles and normal stopping shall be located at the
loading position at a height between 600 mm and 1 700 mm from the floor level.
For the position of emergency stop controls see 5.1.5.
The controls for each sawblade drive motor shall include an indication, e.g. by a light signal or a two position switch
when power is supplied to that motor.
Verification : By checking the relevant drawings and/or circuit diagrams, inspection, measurement and relevant
functional testing on the machine.
5.1.3 Starting
See 9.2.5.2 of EN 60204-1: 1992 and in addition :
For the purposes of this European Standard "all safeguards are in place and functional" is achieved by the
interlocking arrangements described in 5.2.7 and "operational" means rotation of any sawblade spindle.
12
---------------------- Page: 13 ----------------------
EN 1218-3:2001 (E)
It shall be possible to start each sawblade drive motor separately.
Verification : By checking the relevant drawings and/or circuit diagrams, inspection and relevant functional testing
on the machine.
5.1.4 Normal stopping
A stop control shall be fitted which, when actuated, stops all machine actuators and cuts power to them once
stopping is complete.
The category of the stop function (category 0 or 1) shall be in accordance with the requirements of 9.2.2 of EN
60204-1: 1992, where the "safety and/or functional“ requirements of the machine are fulfilled by maintaining power
to the electrical brake (if provided) and/or powered clamping (if provided) until stopping is complete.
These requirements shall be satisfied at the level of the control circuits. If a time delay device is used, the time
delay shall be at least the maximum run-down time. Either the time delay shall be fixed or the time delay
adjustment device shall be sealed.
If the emergency stop provided by virtue of 5.1.5 also achieves at least the above requirements, then the
emergency stop can be regarded as fulfilling the requirements of the normal stop control.
Verification : By checking the relevant drawings and/or circuit diagrams, inspection and relevant functional testing
on the machine.
5.1.5 Emergency stop
See EN 418 : 1992 and in addition :
Machines shall be fitted with an emergency stop control(s) which shall conform to the requirements of 9.2.5.4 and
10.7 of EN 60204-1: 1992. However 10.7.5 of EN 60204-1: 1992 does not apply.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.