This document deals with all significant hazards, hazardous situation and events as listed in Clause 4 relevant
to stationary and displaceable
- surface planning machines,
- thickness planing machines,
- combined surface/thickness planing machines
with an integrated feed in thicknessing mode, (with or without demountable power feed unit in planing mode)
and with manual loading and unloading of the work-piece.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This clause of SIST EN 62841-2-14 is applicable, except as follows: Addition: This part of IEC 62841 applies to planers.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Defines a new subclause on field-strength measurements in the frequency range 1 GHz to 18 GHz.

  • Standard
    19 pages
    English and French language
    sale 15% off

This document specifies the safety requirements and measures for
— surface planing machines, also called jointers,
— thickness planing machines, also called planers or single surface planers,
— combined surface/thickness planing machines
with fixed cutter block position, with an integrated feed in thickness planing mode, with or without demountable power feed device in planing mode, with manual loading and/or unloading of the workpiece and capable of continuous production use, hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
It deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
It is also applicable to surface planing machines and combined surface/thickness planing machines fitted with an optional mortising device, whose hazards have been dealt with.
This document does not apply to:
a) machines with more than one cutter block;
b) machines with a mortising unit driven by a separate motor;
c) machines where the cutter block is adjustable for depth of cut setting in thickness planing mode;
d) machines where the conversion from planing to thickness planing mode or vice versa is achieved by mounting or demounting parts/units;
e) machines where surface planing and thickness planing can be performed on the same section of the cutter block at the same time;
f) machines intended for use in potentially explosive atmosphere;
g) machines manufactured prior to the date of its publication as an international standard.

  • Draft
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies all significant hazards, hazardous situations and events as listed in Clause 4, relevant to stationary and displaceable one side thickness planing machines fitted with an integrated feed and with cutterblock fixed in position and manual loading and unloading of the work-piece, hereinafter referred to as "machines", designed to cut solid wood, chipboard, fibreboard and plywood when they are used as
intended and under the conditions foreseen by the manufacturer.
This document does not apply to machines set up on a bench or a table similar to a bench, which is intended to carry out work in a stationary position, capable of being lifted by one person by hand; hand held planers or any adaptation permitting their use in a different mode, i.e. bench mounting; thickness planing machines where the cutterblock is adjustable for depth of cut setting.
This document is not applicable to one side thickness planning machines fitted with an integrated feed and with cutterblock fixed in position which are manufactured before the date of its publication as EN.

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies all significant hazards, hazardous situation and events as listed in Clause 4 relevant to stationary and displaceable surface planing and thicknessing machines with an integrated feed in thicknessing mode, (with or without demountable power feed unit in planning mode) and with manual loading and unloading of the work-piece, hereinafter referred to as "machines". The cutterblock is fixed in position and for thicknessing an integrated feed is provided. The machines are designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer. This document does not deal with any hazards which result from the attachment of an optional mortising unit. These hazards are covered by prEN 940:2007. This document does not apply to machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand; surface planing and thicknessing machines where the cutterblock is adjustable for depth of cut setting in thicknessing mode; machines where the conversion from planing to thicknessing mode or vice versa is achieved by mounting or demounting parts/units; machines where surfacing and thicknessing can be performed at the same time. This document is not applicable to surface planing and thicknessing machines which are manufactured before the date of its publication as EN.

  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies all significant hazards, hazardous situation and events as listed in Clause 4 relevant to stationary and displaceable hand fed surface planing machines fitted or not with demountable power feed unit hereinafter referred to as "machines" designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer.
This document does not apply to machines set up on a bench or a table similar to a bench, which is intended to carry out work in a stationary position, capable of being lifted by one person by hand; hand held planers or any adaptation permitting their use in a different mode, i.e. bench mounting.
This document is not applicable to hand fed surface planing machines which are manufactured before the date of its publication as EN.

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies all significant hazards, hazardous situations and events as listed in Clause 4, relevant to stationary and displaceable one side thickness planing machines fitted with an integrated feed and with cutterblock fixed in position and manual loading and unloading of the work-piece, hereinafter referred to as "machines", designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Machines which are designed to work wood based materials may also be used for working hardened plastic materials with similar physical characteristics as wood. This document does not apply to: a) machines set up on a bench or a table similar to a bench, which is intended to carry out work in a stationary position, capable of being lifted by one person by hand; b) hand held planers or any adaptation permitting their use in a different mode, i.e. bench mounting; c) thickness planing machines where the cutterblock is adjustable for depth of cut setting. This document is not applicable to one side thickness planning machines fitted with an integrated feed and with cutterblock fixed in position which are manufactured before the date of its publication as EN.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document !specifies all significant hazards, hazardous situation and events as listed in Clause 4 relevant to stationary and displaceable surface planing and thicknessing machines with an integrated feed in thicknessing mode, (with or without demountable power feed unit in planning mode) and with manual loading and unloading of the work-piece, hereinafter referred to as "machines". The cutterblock is fixed in position and for thicknessing an integrated feed is provided. The machines are designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Machines which are designed to work wood based materials may also be used for thicknessing hardened plastic materials with similar physical characteristics as wood. This document does not deal with any hazards which result from the attachment of an optional mortising unit. These hazards are covered by EN 940:2009+A1:2012. This document does not apply to: a) machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand; b) surface planing and thicknessing machines where the cutterblock is adjustable for depth of cut setting in thicknessing mode; c) machines where the conversion from planing to thicknessing mode or vice versa is achieved by mounting or demounting parts/units; d) machines where surfacing and thicknessing can be performed at the same time. This document is not applicable to surface planing and thicknessing machines which are manufactured before the date of its publication as EN.

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document !specifies all significant" hazards, hazardous situation and events as listed in Clause 4 relevant to stationary and displaceable hand fed surface planing machines fitted or not with demountable power feed unit hereinafter referred to as "machines" designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer #including reasonably foreseeable misuse$. #Machines which are designed to work wood based materials may also be used for working hardened plastic materials with similar physical characteristics as wood.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document !specifies all significant hazards, hazardous situation and events as listed in Clause 4 relevant to stationary and displaceable hand fed surface planing machines fitted or not with demountable power feed unit hereinafter referred to as machines designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document deals with all the significant hazards, hazardous situations and events as listed in Clause 4, relevant to stationary and displaceable one side thickness planing machines fitted with an integrated feed and with cutterblock fixed in position and manual loading and unloading of the work-piece, hereinafter referred to as "machines", designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer.
This document does not apply to:
a)   machines set up on a bench or a table similar to a bench, which is intended to carry out work in a stationary position, capable of being lifted by one person by hand;
NOTE 1   Transportable motor-operated electric tools are dealt with in EN 61029-1:2000 together with
prEN 61029-2-3:2004.
b)   hand held planers or any adaptation permitting their use in a different mode, i.e. bench mounting;
NOTE 2   Hand-held motor-operated electric tools are dealt with in EN 60745-1:2003 together with
EN 60745-2-14:2003.
c)   thickness planing machines where the cutterblock is adjustable for depth of cut setting.
This document is not applicable to one side thickness planning machines fitted with an integrated feed and with cutterblock fixed in position which are manufactured before the date of its publication as EN.
NOTE 3    Machines covered by this European Standard are listed under A.3 of Annex IV of the Machinery Directive.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document deals with all the significant hazards, hazardous situation and events as listed in Clause 4 relevant to stationary and displaceable surface planing and thicknessing machines with an integrated feed in thicknessing mode, (with or without demountable power feed unit in planning mode) and with manual loading and unloading of the work-piece, hereinafter referred to as "machines". The cutterblock is fixed in position and for thicknessing an integrated feed is provided. The machines are designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer.
This document does not deal with any hazards which result from the attachment of an optional mortising unit. These hazards are covered by prEN 940:2007.
This document does not apply to:
a)   machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand;
NOTE 1   Transportable motor-operated electric tools are covered by the requirements of EN 61029-1:2000 together with prEN 61029-2-3:2004.
b)   surface planing and thicknessing machines where the cutterblock is adjustable for depth of cut setting in thicknessing mode;
c)   machines where the conversion from planing to thicknessing mode or vice versa is achieved by mounting or demounting parts/units;
d)   machines where surfacing and thicknessing can be performed at the same time.
This document is not applicable to surface planing and thicknessing machines which are manufactured before the date of its publication as EN.
NOTE 2   Machines covered by this document are listed under A.5 of Annex IV of the Machinery Directive.

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document deals with the significant hazards, hazardous situation and events as listed in Clause 4 relevant to stationary and displaceable hand fed surface planing machines fitted or not with demountable power feed unit hereinafter referred to as "machines" designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer.
This document does not apply to:
a)   machines set up on a bench or a table similar to a bench, which is intended to carry out work in a stationary position, capable of being lifted by one person by hand;
NOTE 1   Transportable motor-operated electric tools are dealt with by EN 61029-1:2000 together with
prEN 61029-2-3:2004.
b)   hand held planers or any adaptation permitting their use in a different mode, i.e. bench mounting.
NOTE 2   Hand-held motor-operated electric tools are dealt with by EN 60745-1:2003 together with EN 60745-2-14:2003.
This document is not applicable to hand fed surface planing machines which are manufactured before the date of its publication as EN.
NOTE 3   Machines covered by this document are listed under A.2 of Annex IV of the Machinery Directive.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document deals with the significant hazards, hazardous situation and events as listed in Clause 4, relevant to stationary and displaceable one side thickness planing machines fitted with an integrated feed and with cutterblock fixed in position and manual loading and unloading of the workpiece, hereinafter referred to as "machines", designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer.
This document does not apply to:
a)   machines set up on a bench or a table similar to a bench, which is intended to carry out work in a stationary position, capable of being lifted by one person by hand;
NOTE 1   Transportable motor-operated electric tools are dealt with in EN 61029-1:2000 together with
prEN 61029-2-3:2004.
b)   hand held planers or any adaptation permitting their use in a different mode, i.e. bench mounting;
NOTE 2   Hand-held motor-operated electric tools are dealt with in EN 60745-1:2003 together with
EN 60745-2-14:2003.
c)   thickness planing machines where the cutterblock is adjustable for depth of cut setting.
This document is not applicable to one side thickness planning machines fitted with an integrated feed and with cutterblock fixed in position which are manufactured before the date of its publication as EN.
NOTE 3    Machines covered by this European Standard are listed under A.3 of Annex IV of the Machinery Directive.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document deals with the significant hazards, hazardous situation and events as listed in Clause 4 relevant to stationary and displaceable surface planing and thicknessing machines with an integrated feed in thicknessing mode, (with or without demountable power feed unit in planning mode) and with manual loading and unloading of the workpiece, hereinafter referred to as "machines". The cutterblock is fixed in position and for thicknessing an integrated feed is provided. The machines are designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer.
This document does not deal with any hazards which result from the attachment of an optional mortising unit. These hazards are covered by prEN 940:2006.
This document does not apply to:
a)   machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand;
NOTE 1   Transportable motor-operated electric tools are covered by the requirements of EN 61029-1:2000 together with prEN 61029-2-3:2004.
b)   surface planing and thicknessing machines where the cutterblock is adjustable for depth of cut setting in thicknessing mode;
c)   machines where the conversion from planing to thicknessing mode or vice versa is achieved by mounting or demounting parts/units.
This document is not applicable to surface planing and thicknessing machines which are manufactured before the date of its publication as EN.
NOTE 2   Machines covered by this document are listed under A.5 of Annex IV of the Machinery Directive.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document deals with the significant hazards, hazardous situation and events as listed in Clause 4 relevant to stationary and displaceable surface planing and thicknessing machines with an integrated feed in thicknessing mode, (with or without demountable power feed unit in planning mode) and with manual loading and unloading of the work-piece, hereinafter referred to as "machines". The cutterblock is fixed in position and for thicknessing an integrated feed is provided. The machines are designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European standard specifies the requirements and/or measures to remove the hazards and limit the risk on one side thickness planing machines fitted with an integrated feed hereinafter referred to as "machines", designed to cut solid wood, chipboard, fibreboard, plywood and also these materials where they are covered with plastic laminate or edgings.  Electrically driven machines excluded form the scope of this standard are covered by the requirements of EN 61029-1: 1995 or EN 50144-1: 1995 and prEN 61029-2-3: 1996.  This European standard covers all the hazards relevant to this machine. These hazards are listed in clause 4.  This European Standard does not apply to machines set up on a bench or  a table similar to a bench which are intended to carry out work in a stationary position and capable of being lifted by by hand by one person.  This European standard applies to one side thicknessing machines with manual loading and unloading and with cutterblock fixed in position as defined in 3.1.1.  This European standard does not apply to hand held woodworking machines or any adaptation permitting their use in a different mode, i.e. bench mounting. It does not apply to thickness planing machines where the cutterblock is adjustable for depth of cut setting.  This European standard is primarily applicable to machines which are manufactured after the date of issue of this standard.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European standard specifies out the requirements and/or measures to remove the hazards and limit the risk on hand fed surface planing machines hereinafter referred to as "machines" designed to cut solid wood, chipboard, fibreboard, plywood and also these materials where they are covered with plastic laminate or edgings.  Electrically driven machines excluded from the scope of this standard are covered by the requirements of EN 61029-1:1995 or EN 50144-1: 1995 and prEN 61029-2-3: 1996.  This European standard covers all the hazards relevant to this machine. These hazards are listed in clause 4.  This European Standard does not apply to machines set up on a bench or a table similar to a bench which are intended to carry out work in a stationary position and capable of being lifted by one person.  This European standard applies to hand fed surface planing machines which can or can not be designed to be used with a demountable power feed unit.  This European standard applies to woodworking machines fixed in position during working. This includes machines which are fixed whilst working but transportable by the operator from one workstation to another.  This European standard does not apply to hand held woodworking machines or any adaptation permitting their use in a different mode i.e. bench mounting.  This European standard is primarily applicable to machines which are manufactured after the date of issue of this European standard.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European standard specifies the requirements and/or measures to remove the hazards and limit the risk on surface planing and thicknessing machines, hereinafter referred to as machines, designed to cut solid wood, chipboard, fibreboard, plywood and also these materials where they are covered with plastic laminate or edgings.  Electrically driven machines excluded from the scope of this standard are covered by the  requirements of prEN 61029-1: 1996 or EN 50144-1: 1995 and prEN 61029-2-3: 1996.  This European standard covers all the hazards relevant to this machine. These hazards are listed in clause 4.  This Eurpoean Standard does not apply to machines set up on a bench or a table similar to a bench which are intended to carry out work in a stationary position and capable of being lifted by hand by one person.  This European Standard does not apply to hand held woodworking machines or any adaptation permitting their use in a different mode, i.e. bench mounting.  This European Standard applies to surface planing and thickness planing machines with manual loading and unloading and with cutterblock fixed in position fitted or not with demountable power feed unit.  It does not apply to surface planing and thickness planing machines where the cutterblock is adjustable for depth of cut setting.  It does not apply to machines where surfacing and thicknessing can be performed at the same time.  This European Standard is primarily applicable to machines which are manufactured after the date of issue of this standard.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This clause of Part 1 is applicable except as follows:     1.1 Addition: This standard applies to planers with a cutting width up to 150 mm. NOTE - For planers with a cutting width above 150 mm other requirements may apply.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day