SIST EN 14353:2008/kprA1:2009

Metal beads and feature profiles for use with gypsum plasterboards - Definitions, requirements and test methods

This European Standard specifies the characteristics and performance of metal beads, metal beads combined with paper tape and metal feature profiles designed for use in systems made with gypsum plaster boards, gypsum boards with fibrous reinforcement and products from secondary processing complying with the EN's shown in Figure 2, intended to be used in building construction works.
Metal beads and feature profiles, depending upon their material and type, can be featured without decoration, decorated or finished with jointing compounds to receive decoration.
It covers the following performance characteristics : reaction to fire and flexural strengths (bending behaviour) to be measured according the corresponding European test methods.
It provides for the evaluation of conformity of the product to this EN.
This European Standard covers also additional technical characteristics that are of importance for the use and acceptance of the product by the construction industry and the reference tests for these characteristics.

Hilfs- und Zusatzprofile aus Metall zur Verwendung mit Gipsplatten - Begriffe, Anforderungen und Prüfverfahren

Cornières et profilés métalliques pour plaques de plâtres - Définitions, spécifications et méthodes

Pomožni in dodatni kovinski profili za mavčne plošče - Definicije, zahteve in preskusne metode

General Information

• Status: Not Published
• Public Enquiry End Date: 09-Nov-2009
• ICS: 91.100.10 - Cement. Gypsum. Lime. Mortar
• Technical Committee: CAA - Mineral binders and masonry
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 05-May-2011
• Due Date: 10-May-2011
• Completion Date: 05-May-2011
• Directive: Harmonized Standard305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive:

  ---

  Not Harmonized89/106/EEC - Construction products
• Mandate: M/106 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on gypsum products
• Ref Project: EN 14353:2007/FprA1 - Metal beads and feature profiles for use with gypsum plasterboards - Definitions, requirements and test methods

Relations

• Consolidated By: SIST EN 14353:2008+A1:2010 - Metal beads and feature profiles for use with gypsum plasterboards - Definitions, requirements and test methods
• Effective Date: 01-Jul-2010
• Amends: SIST EN 14353:2008 - Metal beads and feature profiles for use with gypsum plasterboards - Definitions, requirements and test methods
• Effective Date: 01-Oct-2009

Overview

SIST EN 14353:2008/kprA1:2009 is a European standard published by CEN that specifies the characteristics, requirements, and test methods for metal beads and feature profiles intended for use with gypsum plasterboards. These products, which can include metal beads combined with paper tape, are essential components in modern building construction, providing edge protection, reinforcement, and feature profiling for various types of gypsum-based wall and ceiling systems.

This standard outlines performance criteria, including reaction to fire and flexural strength, and provides guidance on conformity evaluation. SIST EN 14353:2008/kprA1:2009 addresses additional technical characteristics important for the construction industry, supporting safe, high-quality, and durable installations in line with contemporary building practices in Europe.

Key Topics

• Product Types Covered
  • Metal beads for edges and corners
  • Feature profiles for design and structural requirements
  • Metal beads combined with paper tape
• Gypsum Systems Compatibility
  • Suitable for gypsum plasterboards, boards with fibrous reinforcement, and compliant secondary-processed products
• Performance Characteristics
  • Reaction to fire: Ensures materials contribute to fire safety performance in buildings
  • Flexural strength: Assesses the bending behavior of profiles for robust protection and longevity
• Material and Coating Standards
  • References to steel and aluminum standards (e.g., EN 10346, EN 10152, EN 755)
  • Protective coating requirements for corrosion resistance and durability
• Test Methods & Evaluation
  • Describes applicable European test methods for critical properties
  • Guidance on measuring thickness, dimensions, and coating compliance

Applications

SIST EN 14353:2008/kprA1:2009 is highly relevant across the construction industry, notably in:

• Interior drywall systems: Metal beads and feature profiles protect exposed edges, corners, and joint areas, reducing damage and facilitating smooth finishing.
• Partition walls and ceilings: Provides structural reinforcement, especially where boards may be subject to impact or movement.
• Decorative finishing: Supports the creation of aesthetic features and sharp edges with consistent quality.
• Fire safety compliance: By specifying reaction to fire and conformity processes, the standard helps ensure that building components contribute to overall fire safety objectives.
• Moisture and corrosion resistance: Prescribes materials and protective coatings suitable for environments prone to moisture, safeguarding longevity.
• Conformity and Quality Assurance: Provides manufacturers, designers, and contractors with a basis for product assessment, CE marking, and regulatory compliance.

Related Standards

Professionals working with metal beads and plasterboard profiles should consult these related standards:

• EN 10139 – Cold rolled uncoated mild steel narrow strip for cold forming
• EN 10152 – Electrolytically zinc coated cold rolled steel flat products
• EN 10346 – Continuously hot-dip coated steel flat products
• EN ISO 9227 – Corrosion tests in artificial atmospheres (Salt spray tests)
• EN 755 – Aluminum and aluminum alloys (extruded rods, bars, etc.)
• EN 15283-1 and EN 15283-2 – Gypsum boards with fibrous reinforcement

By following SIST EN 14353:2008/kprA1:2009 and related references, the construction industry can maintain high standards for durability, safety, and aesthetic quality in gypsum board installations, meeting both regulatory obligations and client expectations.

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2009
3RPRåQLLQGRGDWQLNRYLQVNLSURILOL]DPDYþQHSORãþH'HILQLFLMH]DKWHYHLQ
SUHVNXVQHPHWRGH
Metal beads and feature profiles for use with gypsum plasterboards - Definitions,
requirements and test methods
Hilfs- und Zusatzprofile aus Metall zur Verwendung mit Gipsplatten - Begriffe,
Anforderungen und Prüfverfahren
Cornières et profilés métalliques pour plaques de plâtres - Définitions, spécifications et
méthodes
Ta slovenski standard je istoveten z: EN 14353:2007/FprA1
ICS:
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 14353:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2009
ICS 91.100.10
English Version
Metal beads and feature profiles for use with gypsum
plasterboards - Definitions, requirements and test methods
Cornières et profilés métalliques pour plaques de plâtres - Hilfs- und Zusatzprofile aus Metall zur Verwendung mit
Définitions, spécifications et méthodes Gipsplatten - Begriffe, Anforderungen und Prüfverfahren
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 241.
This draft amendment A1, if approved, will modify the European Standard EN 14353:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14353:2007/FprA1:2009: E
worldwide for CEN national Members.

Foreword
This document (EN 14353:2007/FprA1:2009) has been prepared by Technical Committee CEN/TC 241
“Gypsum and gypsum based products”, the secretariat of which is held by AFNOR.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
1 Modifications to Clause 2
Add the following references:
"EN 10139, Cold rolled uncoated mild steel narrow strip for cold forming - Technical delivery conditions",
"EN 10152, Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery
conditions",
"EN ISO 9227, Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2006)",
"EN 10346, Continuously hot-dip coated steel flat products – Technical delivery conditions".
Delete the following references:
"EN 10326, Continuously hot-dip coated strip and sheet of structural steels — Technical delivery conditions
EN 10327, Continuously hot-dip coated strip and sheet of low carbon steels for cold forming — Technical
delivery conditions".
Replace the references to prEN 15283-1 and prEN 15283-2 with EN 15283-1 and EN 15283-2 in Clause 2
and throughout the document.
Replace the reference to EN ISO 1924-2 with the following:
"EN ISO 1924-2, Paper and board — Determination of tensile properties — Part 2: Constant rate of elongation
method (20 mm/min) (ISO 1924-2:2008)".
2 Addition of 3.1, General terms
Insert the following new sub-clause 3.1 after the standard paragraph:
"3.1 General terms".
3 Modification to 3.1 – 3.14
Replace numbering of clauses 3.1 – 3.14 with 3.1.1 – 3.1.14.
4 Addition of 3.2, Symbols and abbreviations
Insert the following new sub-clause 3.2 after 3.1.14:
"3.2 Symbols and abbreviations
For the purpose of simplification in product marking and performance information characteristics may be
identified through the symbols and abbreviations given in Table 1.
...