Plain bearings - Thin-walled half bearings with or without flange - Part 2: Measurement of wall thickness and flange thickness

This part of ISO 3548 specifies, in accordance with ISO 12301, the checking of the wall-thickness of thinwalled half bearings with or without flange and describes the required checking methods and measuring equipment. It applies to a maximum bearing diameter of 150 mm. If this part of ISO 3548 is applied to a greater diameter, an agreement can be formulated between the supplier and the user.

Gleitlager - Dünnwandige Lagerschalen mit oder ohne Bund - Teil 2: Messung der Wanddicke

Paliers lisses - Demi-coussinets minces à ou sans collerette - Partie 2: Mesurage de l'épaisseur de paroi et de l'épaisseur de collerette

Drsni ležaji - Tankosteni polovični ležaji s prirobnico ali brez nje - 2. del: Merjenje debelin stene in prirobnice

Ta del ISO 3548 v skladu z ISO 12301 določa preverjanje debeline stene tankostenih polovičnih ležajev s prirobnico ali brez nje in opisuje zahtevane metode za preverjanje ter merilno opremo. Velja za največji premer ležaja 150 mm. Če se ta del ISO 3548 uporabi pri večjem premeru, se o tem lahko dogovorita dobavitelj in uporabnik.

General Information

Status
Withdrawn
Public Enquiry End Date
24-Jul-2009
Publication Date
23-Dec-2009
Withdrawal Date
01-Sep-2021
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
02-Sep-2021
Due Date
25-Sep-2021
Completion Date
02-Sep-2021

Relations

Buy Standard

Standard
ISO 3548-2:2010
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 3548-2:2009 - Plain bearings -- Thin-walled half bearings with or without flange
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 3548-2:2010
01-februar-2010
'UVQLOHåDML7DQNRVWHQLSRORYLþQLOHåDMLVSULUREQLFRDOLEUH]QMHGHO0HUMHQMH
GHEHOLQVWHQHLQSULUREQLFH
Plain bearings - Thin-walled half bearings with or without flange - Part 2: Measurement of
wall thickness and flange thickness
Gleitlager - Dünnwandige Lagerschalen mit oder ohne Bund - Teil 2: Messung der
Wanddicke
Paliers lisses - Demi-coussinets minces à ou sans collerette - Partie 2: Mesurage de
l'épaisseur de paroi et de l'épaisseur de collerette
Ta slovenski standard je istoveten z: ISO 3548-2:2009
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 3548-2:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 3548-2:2010

---------------------- Page: 2 ----------------------

SIST ISO 3548-2:2010

INTERNATIONAL ISO
STANDARD 3548-2
First edition
2009-08-15

Plain bearings — Thin-walled
half bearings with or without flange —
Part 2:
Measurement of wall thickness
and flange thickness
Paliers lisses — Demi-coussinets minces à collerette ou sans
collerette —
Partie 2: Mesurage de l'épaisseur de paroi et de l'épaisseur
de collerette




Reference number
ISO 3548-2:2009(E)
©
ISO 2009

---------------------- Page: 3 ----------------------

SIST ISO 3548-2:2010
ISO 3548-2:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 3548-2:2010
ISO 3548-2:2009(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Symbols and units.2
5 Purpose of checking .2
6 Checking methods .3
6.1 Measuring principle.3
6.2 Line measurement around the circumference .3
6.3 Line measurement in the axial direction.4
6.4 Point measurement .5
6.5 Grading of bearings .6
6.6 Eccentric bore.6
7 Requirements for measuring equipment and specimen for the contact method.6
7.1 Radius for measuring the outside surface .6
7.2 Radius for measuring the inside surface.6
7.3 Measuring pin load.7
7.4 Set-up.7
7.5 Periodic checking.7
7.6 Failures on the inside and/or outside surface.7
8 Checking of measuring equipment .7
Bibliography.8

© ISO 2009 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 3548-2:2010
ISO 3548-2:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3548-2 was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 5, Quality
analysis and assurance.
Together with ISO 3547-7, this part of ISO 3548 replaces ISO 12306, which has been cancelled.
ISO 3548 consists of the following parts, under the general title Plain bearings — Thin-walled half bearings
with or without flange:
⎯ Part 2: Measurement of wall thickness and flange thickness
1)
Tolerances, design features and methods of test is to form the subject of a part 1 of ISO 3548 and the
measurement of peripheral length is to form the subject of a part 3.



1) It is intended to replace ISO 3548:1999 with ISO 3548-1.
iv © ISO 2009 – All rights reserved

---------------------- Page: 6 ----------------------

SIST ISO 3548-2:2010
INTERNATIONAL STANDARD ISO 3548-2:2009(E)

Plain bearings — Thin-walled half bearings with or without
flange —
Part 2:
Measurement of wall thickness and flange thickness
1 Scope
This part of ISO 3548 specifies, in accordance with ISO 12301, the checking of the wall-thickness of thin-
walled half bearings with or without flange and describes the required checking methods and measuring
equipment. It applies to a maximum bearing diameter of 150 mm. If this part of ISO 3548 is applied to a
greater diameter, an agreement can be formulated between the supplier and the user.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document
...

INTERNATIONAL ISO
STANDARD 3548-2
First edition
2009-08-15

Plain bearings — Thin-walled
half bearings with or without flange —
Part 2:
Measurement of wall thickness
and flange thickness
Paliers lisses — Demi-coussinets minces à collerette ou sans
collerette —
Partie 2: Mesurage de l'épaisseur de paroi et de l'épaisseur
de collerette




Reference number
ISO 3548-2:2009(E)
©
ISO 2009

---------------------- Page: 1 ----------------------
ISO 3548-2:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3548-2:2009(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Symbols and units.2
5 Purpose of checking .2
6 Checking methods .3
6.1 Measuring principle.3
6.2 Line measurement around the circumference .3
6.3 Line measurement in the axial direction.4
6.4 Point measurement .5
6.5 Grading of bearings .6
6.6 Eccentric bore.6
7 Requirements for measuring equipment and specimen for the contact method.6
7.1 Radius for measuring the outside surface .6
7.2 Radius for measuring the inside surface.6
7.3 Measuring pin load.7
7.4 Set-up.7
7.5 Periodic checking.7
7.6 Failures on the inside and/or outside surface.7
8 Checking of measuring equipment .7
Bibliography.8

© ISO 2009 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3548-2:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3548-2 was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 5, Quality
analysis and assurance.
Together with ISO 3547-7, this part of ISO 3548 replaces ISO 12306, which has been cancelled.
ISO 3548 consists of the following parts, under the general title Plain bearings — Thin-walled half bearings
with or without flange:
⎯ Part 2: Measurement of wall thickness and flange thickness
1)
Tolerances, design features and methods of test is to form the subject of a part 1 of ISO 3548 and the
measurement of peripheral length is to form the subject of a part 3.



1) It is intended to replace ISO 3548:1999 with ISO 3548-1.
iv © ISO 2009 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 3548-2:2009(E)

Plain bearings — Thin-walled half bearings with or without
flange —
Part 2:
Measurement of wall thickness and flange thickness
1 Scope
This part of ISO 3548 specifies, in accordance with ISO 12301, the checking of the wall-thickness of thin-
walled half bearings with or without flange and describes the required checking methods and measuring
equipment. It applies to a maximum bearing diameter of 150 mm. If this part of ISO 3548 is applied to a
greater diameter, an agreement can be formulated between the supplier and the user.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3548, Plain bearings — Thin-walled half bearings with or without flange — Tolerances, design features
and methods of test
ISO 12301, Plain bearings — Quality control techniques and inspection of geometrical and material quality
characteristics
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
wall thickness
s
3
radial distance between the opposing measuring points at the inside and the outside
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.