oSIST prEN 18120-9:2024
(Main)Packaging - Design for recycling of plastic packaging - Part 9: Guideline for EPS packaging
Packaging - Design for recycling of plastic packaging - Part 9: Guideline for EPS packaging
This document covers the design of EPS rigid packaging with respect to compatibility of the design with the collecting, sorting, and recycling processes.
Packaging constituents and packaging components made of other materials than PS are also covered by this document as they need to be evaluated on compatibility with polymer recycling.
Verpackung - Recyclingorientierte Gestaltung von Kunststoffverpackungsprodukten - Teil 8: Leitfaden und Protokolle für Verpackungen aus PS
Dieses Dokument behandelt die Gestaltung starrer EPS Verpackungen im Hinblick auf die Kompatibilität der Gestaltung mit den Sammlungs-, Sortier- und Recyclingprozessen.
Verpackungselemente und -bestandteile aus anderen Materialien als PS werden ebenfalls durch dieses Dokument behandelt, da sie hinsichtlich ihrer Kompatibilität mit dem Polymer-Recycling bewertet werden müssen.
Emballages - Conception des emballages plastiques en vue de leur recyclage - Partie 9 : Lignes directrices pour les emballages en PSE
Le présent document traite de la conception d’emballages rigides en PSE, et plus particulièrement de la compatibilité de la conception avec les processus de collecte, de tri et de recyclage.
Les constituants et composants d’emballages fabriqués à partir de matériaux autres que le PS sont également couverts par le présent document, car il est nécessaire d’évaluer leur compatibilité avec le recyclage du polymère.
Embalaža - Načrtovanje, ki omogoča recikliranje plastične embalaže - 9. del: Smernica za plastično embalažo iz ekspandiranega polistirena (EPS)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Embalaža - Načrtovanje, ki omogoča recikliranje plastične embalaže - 9. del:
Smernica za plastično embalažo iz ekspandiranega polistirena (EPS)
Packaging - Design for recycling of plastic packaging - Part 9: Guideline for EPS
packaging
Verpackung - Recyclingorientierte Gestaltung von Kunststoffverpackungsprodukten - Teil
8: Leitfaden und Protokolle für Verpackungen aus PS
Ta slovenski standard je istoveten z: prEN 18120-9
ICS:
13.030.50 Recikliranje Recycling
55.020 Pakiranje in distribucija blaga Packaging and distribution of
na splošno goods in general
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2024
ICS 55.020; 13.030.50; 83.080.20
English Version
Packaging - Design for recycling of plastic packaging - Part
9: Guideline for EPS packaging
Verpackung - Recyclingorientierte Gestaltung von
Kunststoffverpackungsprodukten - Teil 8: Leitfaden
und Protokolle für Verpackungen aus PS
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 261.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 18120-9:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Design compatibility of EPS protective packaging and fish boxes with recycling. 6
4.1 General. 6
4.2 General considerations for EPS packaging . 7
4.3 Sortability . 7
4.4 Design guidelines summary table . 8
Bibliography . 10
European foreword
This document (prEN 18120-9:2024) has been prepared by Technical Committee CEN/TC 261
“Packaging”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
Introduction
EN 18120 consisting of 15 parts aims via a series of guidelines and protocols to establish consistency and
improvement for the Design for recycling of household, industrial and commercial plastic packaging.
— Part 1: Definitions and principles for design-for-recycling of plastic packaging
— Part 2: Process and governance to evaluate the recyclability of plastic packaging
— Part 3: Sortability evaluation process for plastic packaging
— Part 4: Guideline for PET bottles
— Part 5: Guideline for PET rigid packaging (except bottle)
— Part 6: Guideline for PE and PP rigid packaging
— Part 7: Guideline and protocols for PE and PP flexible packaging
— Part 8: Guideline for PS and XPS packaging
— Part 9: Guideline for EPS packaging
— Part 10: Recyclability evaluation process for plastic packaging — Protocols for PET bottles
— Part 11: Recyclability evaluation process for plastic packaging — Protocols for PET other rigid
packaging
— Part 12: Recyclability evaluation process for plastic packaging — Protocols for PE and PP rigid
packaging
— Part 13: Recyclability evaluation process for plastic packaging — Protocols for PE and PP flexible
packaging
— Part 14: Recyclability evaluation process for plastic packaging — Protocols for PS and XPS packaging
— Part 15: Recyclability evaluation process for plastic packaging — Protocols for EPS packaging
Design for recycling guidelines are a common way of describing compatibility with plastic packaging
collection, sorting and recycling into high quality recycled plastic into state-of-the-art facilities. They
provide guidance on the level compatibility, defined as:
— green: Packaging constituents with full compatibility with recycling;
— yellow: Packaging constituents with limited compatibility with recycling;
— red: Packaging constituents which are not compatible with recycling.
Recyclability guidelines will require regular review and improvement to reflect innovations in design,
collection, sorting and recycling.
The Design for recycling guidelines provided in this series of standards are representative of the state of
the art in Europe and cover all steps from design for recycling, packaging waste collection, sorting,
recycling into recycled plastic and to use in a new application.
Packaging recyclability is the combination of five parameters: packaging designed for recycling,
packaging waste collection, sorting when necessary, recycling and use of recycled plastic in a new
application. This series of standards covers one pa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.