Shell boilers - Part 5: Inspection during construction, documentation and marking of pressure parts of the boiler

This Part of the European Standard specifies requirements for the inspection during construction, documentation and marking of shell boilers as defined in EN 12953-1.

Großwasserraumkessel - Teil 5: Prüfung während der Herstellung, Dokumentation und Kennzeichnung für drucktragende Kesselteile

Chaudieres a tubes de fumée - Partie 5: Contrôles en cours de construction, documentation et marquage des parties sous pression des chaudieres

Cette partie de la norme européenne s'applique aux chaudieres a tubes de fumée telles que définies dans le prEN 12953-1:2001.
La présente partie de la norme européenne spécifie les regles d'inspection durant la construction, la documentation et le marquage des chaudieres a tubes de fumée.

Mnogovodni kotli - 5. del : Preskusi med proizvodnjo, dokumentacija in žigosanje tlačno obremenjenih delov kotla

General Information

Status
Withdrawn
Publication Date
31-Oct-2002
Withdrawal Date
08-Jun-2020
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
09-Jun-2020
Due Date
02-Jul-2020
Completion Date
09-Jun-2020

Relations

Buy Standard

Standard
EN 12953-5:2002
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Großwasserraumkessel - Teil 5: Prüfung während der Herstellung, Dokumentation und Kennzeichnung für drucktragende KesselteileChaudieres a tubes de fumée - Partie 5: Contrôles en cours de construction, documentation et marquage des parties sous pression des chaudieresShell boilers - Part 5: Inspection during construction, documentation and marking of pressure parts of the boiler27.060.30Grelniki vode in prenosniki toploteBoilers and heat exchangersICS:Ta slovenski standard je istoveten z:EN 12953-5:2002SIST EN 12953-5:2002en01-november-2002SIST EN 12953-5:2002SLOVENSKI
STANDARD



SIST EN 12953-5:2002



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12953-5May 2002ICS 27.060.30; 27.100English versionShell boilers - Part 5: Inspection during construction,documentation and marking of pressure parts of the boilerChaudières à tubes de fumée - Partie 5: Contrôles en coursde construction, documentation et marquage des partiessous pression des chaudièresGroßwasserraumkessel - Teil 5: Prüfung während derHerstellung, Dokumentation und Kennzeichnung fürdrucktragende KesselteileThis European Standard was approved by CEN on 15 May 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12953-5:2002 ESIST EN 12953-5:2002



EN 12953-5:2002 (E)2ContentsPage1Scope.42Normative references.43Terms and definitions.54Symbols.55Inspection and testing.55.1General.55.2Approval of personnel.55.3Calibration of equipment.65.4Inspection activities.65.5Non-destructive examinations.85.6Weld production control test plates.135.7Final assessment.166Documentation, certification and marking.186.1General.186.2Documentation.196.3Declaration.196.4Marking.19Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or otherprovisions of the Pressure Equipment Directive.20SIST EN 12953-5:2002



EN 12953-5:2002 (E)3ForewordThis document (EN 12953-5:2002) has been prepared by Technical Committee CEN/TC 269 "Shell and water-tubeboilers", the secretariat of which is held by DIN.This European Standard has been prepared under a mandate given to CEN by the European Commission and theEuropean Free Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this standard.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by November 2002, and conflicting national standards shall be withdrawn at the latestby November 2002.The European Standard EN 12953 concerning shell boilers consists of the following Parts: Part 1:General. Part 2:Materials for pressure parts of boilers and accessories. Part 3:Design and calculation for pressure parts. Part 4:Workmanship and construction of pressure parts of the boiler. Part 5:Inspection during construction, documentation and marking of pressure parts of the boiler. Part 6:Requirements for equipment for the boiler. Part 7:Requirements for firing systems for liquid and gaseous fuels for the boiler. Part 8:Requirements for safeguards against excessive pressure. Part 9:Requirements for limiting devices of the boiler and accessories. Part 10:Requirements for boiler feedwater and boiler water quality. Part 11:Acceptance tests. Part 12:Requirements for firing systems for solid fuels for the boiler. Part 13:Operational instructions.CR 12953-14:Guidelines for the involvement of an inspection body independent of the manufacturer.Although, these Parts can be obtained separately, it should be recognized that the Parts are inter-dependent. Assuch, the design and manufacture of shell boilers requires the application of more than one Part in order for therequirements of the standard to be satisfactorily fulfilled.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun-tries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Swe-den, Switzerland and the United Kingdom.SIST EN 12953-5:2002



EN 12953-5:2002 (E)41 ScopeThis Part of the European Standard specifies requirements for the inspection during construction, documentation andmarking of shell boilers as defined in EN 12953-1.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 288-3:1992, Specification and approval of welding procedures for metallic materials — Part 3: Welding proce-dure tests for the arc welding of steels.EN 473, Non destructive testing — Qualification and certification of NDT personnel — General principles.EN 571-1, Non-destructive testing — Penetrate testing — Part 1: General principles.EN 764, Pressure equipment — Terminology and symbols — Pressure, temperature, volume.EN 875, Destructive tests on welds in metallic materials — Impact tests — Test specimen location, notch orienta-tion and examination.EN 876, Destructive tests on welds in metallic materials — Longitudinal tensile test on weld metal in fusion weldedjoints.EN 895, Destructive tests on welds in metallic materials — Transverse tensile test.EN 910, Destructive tests on welds in metallic materials — Bend tests.EN 970, Non-destructive examination of fusion welds — Visual examination.EN 1290, Non-destructive examination of welds — Magnetic particle examination of welds.EN 1321, Destructive tests on welds in metallic materials — Macroscopic and microscopic examination of welds.EN 1435, Non-destructive examination of welds — Radiographic examination of welded joints.EN 1712, Non-destructive examination of welds — Ultrasonic examination of welded joints — Acceptance levels.EN 1713, Non-destructive examination of welds — Ultrasonic examination — Characterization of indications inwelds.EN 1714, Non-destructive examination of welds — Ultrasonic examination of welded joints.EN 12953-1:2002, Shell boilers — Part 1: General.EN 12953-3:2002, Shell boilers — Part 3: Design and calcula-tion for pressure parts.EN 12953-4:2002, Shell boilers — Part 4: Workmanship under construction of pressure parts of the boiler.EN 25817, Arc-welded joints in steel — Guidance on quality levels for imperfections (ISO 5817:1992).EN ISO 6520-1, Welding and allied processes - Classification of geometric imperfections in metallic materials -Part 1: Fusion welding (ISO 6520-1:1998).SIST EN 12953-5:2002



EN 12953-5:2002 (E)53 Terms and definitionsFor the purposes of this Part of this European Standard, the terms and definitions given in EN 12953-1 and EN 764apply.4 SymbolsFor the purposes of this Part of this European Standard, the symbols given in EN 12953-1:2002, Table 4-1 shall ap-ply.5 Inspection and testing5.1 GeneralThe manufacturer shall be responsible for ensuring the boiler conforms to the requirements of this European Stan-dard. Conformity shall be confirmed by the completion of a series of inspection activities as given in Table 5.4-1.Depending upon the conformity assessment module chosen by the manufacturer for the design and manufacture ofeach boiler (see EN 12953-1:2002, Annex B), the inspection activities shall involve, to a greater or lesser extent, or-ganisations which are independent of the manufacturer.NOTEFor the guidance of the manufacturer, the specific involvement of such organisations, known as responsible authori-ties (RA), is described in CR 12953-14.The manufacturer shall provide all the necessary access to enable the responsible authority to carry out the activitiesin which it is required to be involved.5.2 Approval of personnel5.2.1 Check of welder and welding operator approvalThe manufacturer shall certify that the welding of the boiler has been done by welders and welding operators whohave been approved under the requirements of EN 12953-4:2002, 5.15.3.2 and the appropriate certification shall bemade available on request.5.2.2 Approval of non-destructive examination personnelFor the purposes of this standard the term non-destructive examination (NDE) covers the conventional techniques ofvisual, radiographic, ultrasonic, magnetic particle examination and/or penetrant testing as specified in 5.5.2 to 5.5.4.Personnel responsible for non-destructive examination, including interpretation, evaluation and reporting shall be cer-tified in accordance with EN 473.An exception to this requirement shall be made for visual examination of welds and final inspection of boilers, forwhich EN 473 is not applicable. Visual examination shall be in accordance with EN 970.Visual examination shall be carried out by experienced personnel having sufficient knowledge in welding techniques,and a full comprehension of this European Standard, to identify and interpret imperfections that might occur at thesurface of the weld and the heat affected zone.Radiographs shall be viewed by personnel qualified to level 2 of EN 473 as a minimum.Magnetic particle inspection, penetrant inspection and ultrasonic examination shall be performed under the direct su-pervision of personnel qualified to level 2 of EN 473 as a minimum.SIST EN 12953-5:2002



EN 12953-5:2002 (E)65.3 Calibration of equipmentThe manufacturer shall establish procedures to ensure that tools, gauges, instruments and other measuring and test-ing devices used in the manufacture and inspection activities affecting boiler quality, are properly controlled, calibratedand adjusted at specific intervals, to maintain accuracy within defined limits.5.4 Inspection activitiesThe manufacturer shall confirm that the boiler components, as a minimum, conform to the requirements of this Euro-pean Standard by performing and authenticating the inspection activities listed in Table 5.4-1.Table 5.4-1 — List of inspection activities to be undertaken by the manufacturerReferenceno.Area of activityInspection operation1Design and general documentation1.1Design data/calculationsEnsure that the design data/calculations conform to:—technical specifications, if applicable—the requirements of this European Standard1.2Manufacturing drawingsEnsure that drawing information conforms to:—design data and calculations—technical specifications, if applicable—the requirements of this European Standard1.3Purchase specificationsEnsure that material and component specificationsconform to:—technical specifications, if applicable—manufacturing drawings—the requirements of this European Standard1.4Specifications for sub-contractedpartsEnsure that the specification for sub-contracted partsconform to:—technical specifications, if applicable—manufacturing drawings—the requirements of this European Standard2Material2.1Material certificatesVerify that certificate information and results conformto the design specification2.2Welding consumablesVerify that the consumables to be used are in accor-dance with the design specification2.3Material identificationIdentify the material with the material certificates andcheck the markings2.4Transfer of identification marksEnsure that the transfer of identification marks is inaccordance with the approved procedure2.5Acceptance of sub-contracted partsVerify that sub-contracted parts conform to themanufacturer's specification3Fabrication and welding3.1Welding procedure specificationsVerify that appropriate welding specifications areavailable and that their contents are compatible withthe welding procedure approvals3.2Welding procedure approvalsVerify that the welding procedures are appropriate forthe materials and the field of welding application, andthat they have been approved by a responsibleauthority3.3Welder approvalVerify that the welder approvals have been approvedby a responsible authority and that they are availableand validSIST EN 12953-5:2002



EN 12953-5:2002 (E)7Table 5.4-1 (continued)ReferenceArea of activityInspection operation3.4Forming proceduresVerify that forming procedures are available,where applicable, and their contents are appropri-ate to the product to be formed3.5Formed partsExamine formed parts in accordance with therequirements of EN 12953-4:2002, clause 53.6Weld preparationsExamine material cut edges where thermal cuttinghas been used and confirm machined preparationsare to the correct profile3.7Weld seam set-upExamine set-up of seams for welding, includingdimensional check3.8WeldingVerify that the welding is conducted in accordancewith the requirements of the welding procedurespecificationWitness removal and marking of production testplatesVerify that any PWHT on production test plates in-dependent of the boiler complies with the specificheat treatment applied to the boilerExamine NDE reports on production test platesIdentify and mark the test specimens taken fromproduction test plates for mechanical tests3.9Production test plates, if anyVerify that the test information and results from themechanical tests contained in the manufacturer'sreport conform to the requirements of this Euro-pean Standard4Non-destructive examination of welds4.1Non-destructive examination proceduresVerify that appropriate non-destructive examina-tion procedures are available and ensure thequalification of the originator is appropriate4.2Non-destructive examination operatorqualificationsEnsure the non-destructive examination operator'squalifications are appropriateScrutinise any radiographs and check confor-mance to the acceptance criteria4.3Non-destructive examination operationVerify that the results of any ultrasonic examina-tion conforms to the acceptance criteria4.4Non-destructive examination reportsVerify that the information and results conform tothe acceptance criteria5Post-weld heat treatment (PWHT)5.1PWHT proceduresVerify that the post-weld heat treatment proceduresconform to this
European Standard5.2PWHT recordsVerify that temperature/time recordings conform tothe requirements of this European Standard6Final inspection and marking6.1Pre-hydrostatic pressure test inspectionCarry out dimensional checking, visual examinationand identification of accessible parts after compo-nent completion, prior to hydrostatic pressure test6.2Hydrostatic pressure testEnsure the final hydrostatic pressure test is carriedout in accordance with the requirements of thisEuropean StandardPerform visual examination on completion of thehydrostatic pressure test6.3Post-hydrostatic pressure test inspectionCheck marking on nameplate6.4Safety devicesEnsure the provision of safety equipment6.5Manufacturer's data dossierEnsure completeness of the data dossier (see 6.2)SIST EN 12953-5:2002



EN 12953-5:2002 (E)85.5 Non-destructive examinations5.5.1 GeneralThe NDE shall be performed after any PWHT.5.5.2 Extent of non-destructive examinationAll welded seams shall be subjected to visual examination and, in addition, to NDE in accordance with Table 5.5-1.Table 5.5-1 — Extent of NDE for welds !"#$%&&&()!!&&&&(!&((!&*"5*"5&&&&*"5*"5&&&&&&&&&&&(!!&&(!!&&*$5*$5(&&&&*85*85(&&&#$&&Type P355GH steel only.bThe percentage of welds to be examined shall include each intersection of longitudinal and circumferential seams. For each longitudinaland circumferential seam there shall be at least one radiograph, or where ultrasonic testing is specified, at least a 200 mm length shallbe examined.cIn each case the section of weld to be tested shall be selected at random.dIf the end plates are fully stayed to each other by bar stays, stay tubes, or a combination of
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.