SIST EN 1852-1:2018/oprA1:2022

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system

This part of EN 1852 specifies the requirements for solid wall pipes with smooth internal and external surfaces extruded from the same compound/formulation throughout the wall, fittings and the system of polypropylene (PP) piping systems intended for use for:
-   non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and
-   non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
This standard covers PP materials without mineral modifiers.
It also specifies the test parameters for the test methods referred to in this standard.
NOTE 1 Solid wall multilayer pipes with different formulation throughout the wall and foamed core pipes are covered by EN 13476-2 [1] (see also CEN ISO/TR 27165 [2]).
This standard covers a range of nominal sizes, and pipe series and gives recommendations concerning colours.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with CEN/TS 1852-2, it is applicable to PP pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 3   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be connected to pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 14.

Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Polypropylen (PP) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem

Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène (PP) - Partie 1: Spécifications pour tubes, raccords et le système

Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 1. del: Specifikacije za cevi, fitinge in sistem - Dopolnilo A1

General Information

• Status: Not Published
• Public Enquiry End Date: 27-Feb-2022
• ICS: 23.040.05 - Pipeline and its parts for external sewage systems
• ICS: 93.030 - External sewage systems
• Technical Committee: PCV - Plastic pipes, fittings and valves
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 02-Nov-2022
• Due Date: 07-Nov-2022
• Completion Date: 02-Nov-2022
• Ref Project: EN 1852-1:2018/prA1 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system

Relations

• Consolidated By: SIST EN 1852-1:2018+A1:2022 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
• Effective Date: 18-Jan-2023
• Consolidated By: SIST EN 1852-1:2018+A1:2022 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
• Effective Date: 19-Jan-2023
• Amends: SIST EN 1852-1:2018 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
• Effective Date: 28-Jul-2021
• Consolidated By: SIST EN 1852-1:2018+A1:2022 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
• Effective Date: 01-Dec-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1852-1:2018/oprA1:2022
01-februar-2022
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 1. del:
Specifikacije za cevi, fitinge in sistem - Dopolnilo A1
Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -
leitungen - Polypropylen (PP) - Teil 1: Anforderungen an Rohre, Formstücke und das
Rohrleitungssystem
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d'assainissement enterrés sans pression - Polypropylène (PP) - Partie 1: Spécifications
pour tubes, raccords et le système
Ta slovenski standard je istoveten z: EN 1852-1:2018/prA1
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN 1852-1:2018/oprA1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 1852-1:2018/oprA1:2022

---------------------- Page: 2 ----------------------
SIST EN 1852-1:2018/oprA1:2022


DRAFT
EUROPEAN STANDARD
EN 1852-1:2018
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
December 2021
ICS 23.040.05
English Version

Plastics piping systems for non-pressure underground
drainage and sewerage - Polypropylene (PP) - Part 1:
Specifications for pipes, fittings and the system
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement drucklose Abwasserkanäle und -leitungen -
enterrés sans pression - Polypropylène (PP) - Partie 1: Polypropylen (PP) - Teil 1: Anforderungen an Rohre,
Spécifications pour tubes, raccords et le système Formstücke und das Rohrleitungssystem
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.

This draft amendment A1, if approved, will modify the European Standard EN 1852-1:2018. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change wit
...