SIST EN 61300-3-51:2015

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-51: Examinations and measurements - Gauge pin withdrawal force for rectangular ferrule multi-fibre connectors (IEC 61300-3-51:2014)

This part of IEC 61300 is intended to describe the procedure required to measure the pin
gauge withdrawal force for rectangular ferrule multi-fibre connectors.
This measurement can be used as an alternative to the measurement of the pin gauge
insertion force, both of which evaluate the fit of the pin gauge(s) into the guide pin hole(s) of
the female-type connector. The experimental verification of interchangeability between them
is shown in Annex A.
For the male-type connector, IEC 61300-3-49 is applied to evaluate how securely the guide
pins are retained in the guide holes.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 3-51: Untersuchungen und Messungen - Prüfstift-Ausziehkraft von rechteckigen Ferrulen von Mehrfachfasersteckverbindern (IEC 61300-3-51:2014)

Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures fondamentales d'essais et de mesures - Partie 3-51: Examens et mesures - Force d'extraction d'une broche calibrée pour des connecteurs multifibres à férule rectangulaire (CEI 61300-3-51:2014)

IEC 61300-3-51:2014 a pour objet de décrire la procédure requise pour mesurer la force d'extraction d'une broche calibrée, pour des connecteurs multifibres à férules rectangulaires. Cette mesure peut être utilisée comme alternative à la mesure de la force d'insertion de la broche calibrée, ces deux mesures évaluant la bonne adaptation de la (des) broche(s) calibrée(s) dans le ou les alésage(s) de la broche de guidage du connecteur femelle. La vérification expérimentale de l'interchangeabilité entre les deux mesures est traitée dans l'Annexe A. Pour les connecteurs mâles, l'IEC 61300-3-49 s'applique pour évaluer la qualité de rétention des broches de guidage dans leurs alésages.
Mots clés: la force d'extraction d'une broche calibrée, la force d'insertion de la broche calibrée

Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 3-51. del: Preiskave in meritve - Izvlačilna sila kalibrirnega trna za pravokotne tulčaste večvlakenske konektorje (IEC 61300-3-51:2014)

Namen tega dela standarda IEC 61300 je opisati postopke za merjenje izvlačilne sile kalibrirnega trna za pravokotne tulčaste večvlakenske konektorje. To merjenje je mogoče uporabiti kot alternativo merjenju vtične sile kalibrirnega trna za ocenjevanje prileganja kalibrirnega trna luknjam vodilnega trna ženskega konektorja. Poskusno preverjanje njihove zamenljivosti je prikazano v dodatku A.
Pri moških konektorjih se standard IEC 61300-3-49 uporablja za ocenjevanje, kako varno so vodilni trni vstavljeni v vodilne luknje.

General Information

• Status: Published
• Publication Date: 26-Feb-2015
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 08-Dec-2014
• Due Date: 12-Feb-2015
• Completion Date: 27-Feb-2015
• Ref Project: EN 61300-3-51:2014 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-51: Examinations and measurements - Pin gauge withdrawal force for rectangular ferrule multi-fibre connectors

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61300-3-51:2015
01-april-2015
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2VQRYQLSUHVNXVQLLQPHULOQL
SRVWRSNLGHO3UHLVNDYHLQPHULWYH,]YODþLOQDVLODNDOLEULUQHJDWUQD]D
SUDYRNRWQHWXOþDVWHYHþYODNHQVNHNRQHNWRUMH,(&
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 3-51: Examinations and measurements - Gauge pin
withdrawal force for rectangular ferrule multi-fibre connectors (IEC 61300-3-51:2014)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 3-51: Untersuchungen und Messungen - Prüfstift-Ausziehkraft von
rechteckigen Ferrulen von Mehrfachfasersteckverbindern (IEC 61300-3-51:2014)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures
fondamentales d'essais et de mesures - Partie 3-51: Examens et mesures - Force
d'extraction d'une broche calibrée pour des connecteurs multifibres à férule rectangulaire
(CEI 61300-3-51:2014)
Ta slovenski standard je istoveten z: EN 61300-3-51:2014
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 61300-3-51:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61300-3-51:2015

---------------------- Page: 2 ----------------------

SIST EN 61300-3-51:2015


EUROPEAN STANDARD EN 61300-3-51

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2014
ICS 33.180.20

English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures -
Part 3-51: Examinations and measurements - Pin gauge
withdrawal force for rectangular ferrule multi-fibre connectors
(IEC 61300-3-51:2014)
Dispositifs d'interconnexion et composants passifs  Lichtwellenleiter - Verbindungselemente und passive
à fibres optiques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren -
mesures - Partie 3-51: Examens et mesures - Force Teil 3-51: Untersuchungen und Messungen - Prüfstift-
d'extraction d'une broche calibrée pour des connecteurs Ausziehkraft von rechteckigen Ferrulen von
multifibres à férule rectangulaire Mehrfachfasersteckverbindern
(CEI 61300-3-51:2014) (IEC 61300-3-51:2014)
This European Standard was approved by CENELEC on 2014-11-14. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 61300-3-51:2014 E

---------------------- Page: 3 ----------------------

SIST EN 61300-3-51:2015
EN 61300-3-51:2014 - 2 -
Foreword
The text of document 86B/3817/FDIS, future edition 1 of IEC 61300-3-51, prepared by SC 86B “Fibre
optic interconnecting devices and passive components” of IEC/TC 86 “Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-3-51:2014.

The following dates are fixed:
(dop) 2015-08-14
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2017-11-14
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 61300-3-51:2014 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated :

IEC 61300-3-49 NOTE Harmonized as EN 61300-3-49.

---------------------- Page: 4 ----------------------

SIST EN 61300-3-51:2015
- 3 - EN 61300-3-51:2014
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu

Publication Year Title EN/HD Year

IEC 61300-3-1 -  Fibre optic interconnecting devices EN 61300-3-1 -
and passive components - Basic test
and measurement procedures -
Part 3-1: Examinations
and measurements - Visual examination
IEC 61754-5 -  Fibre optic connector interfaces - EN 61754-5 -
Part 5: Type MT connector family
IEC 61754-7-1 -  Fibre optic interconnecting devices EN 61754-7-1 -
and passive components - Fibre optic
connector interfaces -
Part 7-1: Type MPO connector family -
One fibre row
IEC 61754-7-2 -  Fibre optic interconnecting devices and EN 61754-7-2 -
passive components - Fibre optic
connector interfaces -
Part 7-2: Type MPO connector family -
Two fibre rows
IEC 61754-10 -  Fibre optic connector interfaces - EN 61754-10 -
Part 10: Type Mini-MPO connector family
IEC 61754-18 -  Fibre optic connector interfaces - EN 61754-18 -
Part 18: Type MT-RJ connector family

---------------------- Page: 5 ----------------------

SIST EN 61300-3-51:2015

---------------------- Page: 6 ----------------------

SIST EN 61300-3-51:2015




IEC 61300-3-51

®


Edition 1.0 2014-10




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –

Part 3-51: Examinations and measurements – Pin gauge withdrawal force for


rectangular ferrule multi-fibre connectors



Dispositifs d’interconnexion et composants passifs à fibres optiques –


Procédures fondamentales d’essais et de mesures –

Partie 3-51: Examens et mesures – Force d'extraction d’une broche calibrée

pour des connecteurs multifibres à férule rectangulaire










INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX Q


ICS 33.180.20 ISBN 978-2-8322-1886-0






Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61300-3-51:2015
– 2 – IEC 61300-3-51:2014 © IEC 2014

CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 General description . 7
3.1 General . 7
3.2 Test conditions . 7
4 Apparatus . 7
4.1 Fixture . 7
4.2 Pin gauge chuck . 7
4.3 Plug gauge chuck . 7
4.4 Pin gauge . 7
4.5 Plug gauge . 8
4.6 Weight . 9
4.7 Tensile testing machine . 9
5 Procedure . 9
5.1 Method A: Method using the weight (Figure 3) . 9
5.2 Method B: Method using the tensile testing machine (Figure 4) . 10
6 Details to be specified . 12
Annex A (informative) Experimental verification of the interchangeability between the
pin gauge insertion force and the pin gauge withdrawal force . 13
A.1 General . 13
A.2 Measurement system . 13
A.3 Measurement sample . 13
A.4 Measurement procedure . 14
A.5 Measurement results . 14
A.6 Conclusion . 15
Annex B (informative) Experimental verification of compatibility of Method A (method
using the weight) and Method B (method using the tensile testing machine) . 16
Bibliography . 17

Figure 1 – Pin gauge. 8
Figure 2 – Plug gauge for guide pin holes . 8
Figure 3 – Method A for examination of pin gauge/plug gauge withdrawal force
(method using the weight) . 10
Figure 4 – Method B for examination of pin gauge/plug gauge withdrawal force
(method using the tensile testing machine) . 11
Figure A.1 – Measurement system . 13
Figure A.2 – Insertion/withdrawal force measurement results . 14
Figure B.1 – Relation between the withdrawal force values measured by Method A and
Method B . 16

---------------------- Page: 8 ----------------------

SIST EN 61300-3-51:2015
IEC 61300-3-51:2014 © IEC 2014 – 3 –
Table 1 – Test conditions . 7
Table 2 – Dimensions of the pin gauge . 8
Table 3 – Dimensions for plug gauge for guide pin holes . 9
Table A.1 – Guide hole pitch of measurement samples . 14

---------------------- Page: 9 ----------------------

SIST EN 61300-3-51:2015
– 4 – IEC 61300-3-51:2014 © IEC 2014

INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 3-51: Examinations and measurements –
Pin gauge withdrawal force for rectangular ferrule multi-fibre connectors

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
...