iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 62127-3:2008/A1:2013

(Amendment)

Ultrasonics - Hydrophones - Part 3: Properties of hydrophones for ultrasonic fields up to 40 MHz

Ultrasonics - Hydrophones - Part 3: Properties of hydrophones for ultrasonic fields up to 40 MHz

This part of IEC 62127 specifies relevant hydrophone characteristics. This standard is applicable to: - hydrophones employing piezoelectric sensor elements, designed to measure the pulsed and continuous wave ultrasonic fields generated by ultrasonic equipment; - hydrophones used for measurements made in water; - hydrophones with or without an associated pre-amplifier.

Ultraschall - Hydrophone - Teil 3: Eigenschaften von Hydrophonen zur Verwendung in Ultraschallfeldern bis zu 40 MHz

Ultrasons - Hydrophones - Partie 3: Propriétés des hydrophones pour les champs ultrasonores jusqu'à 40 MHz

Ultrazvok - Hidrofoni - 3. del: Lastnosti hidrofonov za ultrazvočna polja do 40 MHz

Ta del standarda IEC 62127 določa ustrezne lastnosti hidrofonov. Ta standard se uporablja za: a) hidrofone, ki uporabljajo piezoelektrične senzorne elemente in so zasnovani za merjenje ultrazvočnih polj z impulznimi in neprekinjenimi valovi, ki jih ustvari ultrazvočna oprema, b) hidrofone, ki se uporabljajo za izvajanje meritev v vodi, ter c) hidrofone s povezanim predojačevalnikom ali brez njega.

General Information

Status
Published
Publication Date
27-Aug-2013
ICS
11.040.01 - Medical equipment in general
17.140.50 - Electroacoustics
Technical Committee
I11 - Imaginarni 11
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
27-Aug-2013
Due Date
01-Nov-2013
Completion Date
28-Aug-2013
Ref Project
EN 62127-3:2007/A1:2013 - Ultrasonics - Hydrophones - Part 3: Properties of hydrophones for ultrasonic fields up to 40 MHz

Relations

Amends
SIST EN 62127-3:2008 - Ultrasonics - Hydrophones -- Part 3: Properties of hydrophones for ultrasonic fields up to 40 MHz
Effective Date
27-Sep-2011
Revised
SIST EN IEC 62127-3:2023 - Ultrasonics - Hydrophones - Part 3: Properties of hydrophones for ultrasonic fields (IEC 62127-3:2022)
Effective Date
21-Dec-2021

Buy Standard

EN 62127-3:2008/A1:2013EN 62127-3:2008/A1:2013
PreviousNext
Amendment
EN 62127-3:2008/A1:2013
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 62127-3:2008/A1:2013
01-oktober-2013
8OWUD]YRN+LGURIRQLGHO/DVWQRVWLKLGURIRQRY]DXOWUD]YRþQDSROMDGR0+]
Ultrasonics - Hydrophones - Part 3: Properties of hydrophones for ultrasonic fields up to
40 MHz
Ultraschall - Hydrophone - Teil 3: Eigenschaften von Hydrophonen zur Verwendung in
Ultraschallfeldern bis zu 40 MHz
Ultrasons - Hydrophones - Partie 3: Propriétés des hydrophones pour les champs
ultrasonores jusqu'à 40 MHz
Ta slovenski standard je istoveten z: EN 62127-3:2007/A1:2013
ICS:
11.040.01 Medicinska oprema na Medical equipment in general
splošno
17.140.50 Elektroakustika Electroacoustics
SIST EN 62127-3:2008/A1:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 62127-3:2008/A1:2013

---------------------- Page: 2 ----------------------

SIST EN 62127-3:2008/A1:2013

EUROPEAN STANDARD
EN 62127-3/A1

NORME EUROPÉENNE
August 2013
EUROPÄISCHE NORM

ICS 17.140.50


English version


Ultrasonics -
Hydrophones -
Part 3: Properties of hydrophones for ultrasonic fields up to 40 MHz
(IEC 62127-3:2007/A1:2013)


Ultrasons -  Ultraschall -
Hydrophones - Hydrophone -
Partie 3: Propriétés des hydrophones pour Teil 3: Eigenschaften von Hydrophonen
les champs ultrasonores jusqu'à 40 MHz zur Verwendung in Ultraschallfeldern bis
(CEI 62127-3:2007/A1:2013) zu 40 MHz
(IEC 62127-3:2007/A1:2013)





This amendment A1 modifies the European Standard EN 62127-3:2007; it was approved by CENELEC on 2013-
07-02. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate
the conditions for giving this amendment the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62127-3:2007/A1:2013 E

---------------------- Page: 3 ----------------------

SIST EN 62127-3:2008/A1:2013
EN 62127-3:2007/A1:2013 - 2 -

Foreword
The text of document 87/530/FDIS, future IEC 62127-3:2007/A1, prepared by IEC/TC 87 "Ultrasonics"
was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62127-
3:2007/A1:2013.
The following dates are fixed:
• latest date by which the document has (dop) 2014-04-02
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2016-07-02
• latest date by which the national
standards conflicting with the

document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 62127-3:2007/A1:2013 was approved by CENELEC as a
European Standard without any modification.

---------------------- Page: 4 ----------------------

SIST EN 62127-3:2008/A1:2013



IEC 62127-3

®


Edition 1.0 2013-05




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE




AMENDMENT 1

AMENDEMENT 1




...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 62127-3:2023(Main)
Ultrasonics - Hydrophones - Part 3: Properties of hydrophones for ultrasonic fields (IEC 62127-3:2022)
EN IEC 62127-3:2023

IEC 62127-3:2022 is available as IEC 62127-3:2022 which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62127-3:2022 specifies relevant hydrophone characteristics. This document is applicable to:
- hydrophones employing piezoelectric sensor elements, designed to measure the pulsed and continuous wave ultrasonic fields generated by ultrasonic equipment;
- hydrophones used for measurements made in water;
- hydrophones with or without an associated pre-amplifier.
IEC 62127-3:2022 cancels and replaces the first edition published in 2007 and Amendment 1:2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition.
a) The upper frequency limit of 40 MHz has been removed.
b) Hydrophone sensitivity definitions have been changed to recognize sensitivities as complex-valued quantities.
c) Procedures to determine the effective hydrophone size have been changed according to the rationale outlined in Annex B.
d) Requirements on the frequencies for which the effective hydrophone size shall be provided have been changed to achieve practicality for increased frequency bands.
e) The new Annex B and Annex C have been added.
f) Annex A has been updated to reflect the changes of the normative parts.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62127-1:2022(Main)
Ultrasonics - Hydrophones - Part 1: Measurement and characterization of medical ultrasonic fields (IEC 62127-1:2022)
EN IEC 62127-1:2022

This part of IEC 62127 specifies methods of use of calibrated hydrophones for the
measurement in liquids of acoustic fields generated by ultrasonic medical equipment including
bandwidth criteria and calibration frequency range requirements in dependence on the spectral
content of the fields to be characterized.
This document:
– defines a group of acoustic parameters that can be measured on a physically sound basis;
– defines a second group of parameters that can be derived under certain assumptions from
these measurements, and called derived intensity parameters;
– defines a measurement procedure that can be used for the determination of acoustic
pressure parameters;
– defines the conditions under which the measurements of acoustic parameters can be made
using calibrated hydrophones;
– defines procedures for correcting for limitations caused by the use of hydrophones with
finite bandwidth and finite active element size, and for estimating the corresponding
uncertainties.
NOTE 1 Throughout this document, SI units are used. In the specification of certain parameters, such as beam
areas and intensities, it can be convenient to use decimal multiples or submultiples. For example, beam area is
likely to be specified in cm2 and intensities in W/cm2 or mW/cm2.
NOTE 2 The hydrophone as defined can be of a piezoelectric or an optic type.

  • Standard
    105 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62127-2:2008/A2:2017(Amendment)
Ultrasonics - Hydrophones - Part 2: Calibration for ultrasonic fields up to 40 MHz (IEC 62127-2:2007/A2:2017)
EN 62127-2:2007/A2:2017
  • Amendment
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62127-2:2008/A1:2014(Amendment)
Ultrasonics - Hydrophones - Part 2: Calibration for ultrasonic fields up to 40 MHz
EN 62127-2:2007/A1:2013

This part of IEC 62127 specifies: absolute hydrophone calibration methods; relative (comparative) hydrophone calibration methods. Recommendations and references to accepted literature are made for the various relative and absolute calibration methods in the frequency range covered by this standard. This standard is applicable to hydrophones used for measurements made in water and in the ultrasonic frequency range up to 40 MHz; hydrophones employing circular piezoelectric sensor elements, designed to measure the pulsed wave and continuous wave ultrasonic fields generated by ultrasonic equipment; hydrophones with or without a hydrophone pre-amplifier.

  • Amendment
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62127-1:2008/A1:2014(Amendment)
Ultrasonics - Hydrophones - Part 1: Measurement and characterization of medical ultrasonic fields up to 40 MHz
EN 62127-1:2007/A1:2013

This part of IEC 62127 specifies methods of use of calibrated hydrophones for the measurement in liquids of acoustic fields generated by ultrasonic medical equipment operating
in the frequency range up to 40 MHz. The objectives of this standard are:
– to define a group of acoustic parameters that can be measured on a physically sound basis;
– to define a second group of parameters that can be derived under certain assumptions from these measurements, and called derived intensity parameters;
– to define a measurement procedure that may be used for the determination of acoustic pressure parameters;
– to define the conditions under which the measurements of acoustic parameters can be made in the frequency range up to 40 MHz using calibrated hydrophones;
– to define procedures for correcting, for limitations caused by the use of hydrophones with finite bandwidth and finite active element size.
NOTE 1 Throughout this standard, SI units are used. In the specification of certain parameters, such as beam areas and intensities, it may be convenient to use decimal multiples or submultiples. For example beam area may be specified in cm2 and intensities in W/cm2 or mW/cm2.
NOTE 2 The hydrophone as defined may be of a piezoelectric or an optic type. The introduction however implies that optical hydrophones are not covered.

  • Amendment
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62127-1:2008(Main)
Ultrasonics - Hydrophones -- Part 1: Measurement and characterization of medical ultrasonic fields up to 40 MHz
EN 62127-1:2007

This part of IEC 62127 specifies methods of use of calibrated hydrophones for the measurement in liquids of acoustic fields generated by ultrasonic medical equipment operating in the frequency range up to 40 MHz. The objectives of this standard are: - to define a group of acoustic parameters that can be measured on a physically sound basis; - to define a second group of parameters that can be derived under certain assumptions from these measurements, and called derived intensity parameters; - to define a measurement procedure that may be used for the determination of acoustic pressure parameters; - to define the conditions under which the measurements of acoustic parameters can be made in the frequency range up to 40 MHz using calibrated hydrophones; - to define procedures for correcting, for limitations caused by the use of hydrophones with finite bandwidth and finite active element size.

  • Standard
    83 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62127-2:2008(Main)
Ultrasonics - Hydrophones -- Part 2: Calibration for ultrasonic fields up to 40 MHz
EN 62127-2:2007

This part of IEC 62127 specifies: absolute hydrophone calibration methods; relative (comparative) hydrophone calibration methods. Recommendations and references to accepted literature are made for the various relative and absolute calibration methods in the frequency range covered by this standard. This standard is applicable to hydrophones used for measurements made in water and in the ultrasonic frequency range up to 40 MHz; hydrophones employing circular piezoelectric sensor elements, designed to measure the pulsed wave and continuous wave ultrasonic fields generated by ultrasonic equipment; hydrophones with or without a hydrophone pre-amplifier.

  • Standard
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62127-3:2008(Main)
Ultrasonics - Hydrophones -- Part 3: Properties of hydrophones for ultrasonic fields up to 40 MHz
prEN 45510-2-1

This part of IEC 62127 specifies relevant hydrophone characteristics. This standard is applicable to: - hydrophones employing piezoelectric sensor elements, designed to measure the pulsed and continuous wave ultrasonic fields generated by ultrasonic equipment; - hydrophones used for measurements made in water; - hydrophones with or without an associated pre-amplifier.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62127-3:2023(Main)
Ultrasonics - Hydrophones - Part 3: Properties of hydrophones for ultrasonic fields (IEC 62127-3:2022)
EN IEC 62127-3:2023

IEC 62127-3:2022 is available as IEC 62127-3:2022 which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62127-3:2022 specifies relevant hydrophone characteristics. This document is applicable to:
- hydrophones employing piezoelectric sensor elements, designed to measure the pulsed and continuous wave ultrasonic fields generated by ultrasonic equipment;
- hydrophones used for measurements made in water;
- hydrophones with or without an associated pre-amplifier.
IEC 62127-3:2022 cancels and replaces the first edition published in 2007 and Amendment 1:2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition.
a) The upper frequency limit of 40 MHz has been removed.
b) Hydrophone sensitivity definitions have been changed to recognize sensitivities as complex-valued quantities.
c) Procedures to determine the effective hydrophone size have been changed according to the rationale outlined in Annex B.
d) Requirements on the frequencies for which the effective hydrophone size shall be provided have been changed to achieve practicality for increased frequency bands.
e) The new Annex B and Annex C have been added.
f) Annex A has been updated to reflect the changes of the normative parts.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62127-1:2022(Main)
Ultrasonics - Hydrophones - Part 1: Measurement and characterization of medical ultrasonic fields (IEC 62127-1:2022)
EN IEC 62127-1:2022

This part of IEC 62127 specifies methods of use of calibrated hydrophones for the
measurement in liquids of acoustic fields generated by ultrasonic medical equipment including
bandwidth criteria and calibration frequency range requirements in dependence on the spectral
content of the fields to be characterized.
This document:
– defines a group of acoustic parameters that can be measured on a physically sound basis;
– defines a second group of parameters that can be derived under certain assumptions from
these measurements, and called derived intensity parameters;
– defines a measurement procedure that can be used for the determination of acoustic
pressure parameters;
– defines the conditions under which the measurements of acoustic parameters can be made
using calibrated hydrophones;
– defines procedures for correcting for limitations caused by the use of hydrophones with
finite bandwidth and finite active element size, and for estimating the corresponding
uncertainties.
NOTE 1 Throughout this document, SI units are used. In the specification of certain parameters, such as beam
areas and intensities, it can be convenient to use decimal multiples or submultiples. For example, beam area is
likely to be specified in cm2 and intensities in W/cm2 or mW/cm2.
NOTE 2 The hydrophone as defined can be of a piezoelectric or an optic type.

  • Standard
    105 pages
    English language
    sale 10% off
    e-Library read for
    1 day