SIST EN 62358:2013
(Main)Ferrite cores - Standard inductance factor for gapped cores and its tolerance
Ferrite cores - Standard inductance factor for gapped cores and its tolerance
This International Standard provides standard AL values (inductance factors) and their tolerances of Pot, RM, ETD, E, EER, EP, PQ and low-profile gapped ferrite cores.
Ferritkerne - Standard-Induktivitätsfaktor für Kerne mit Luftspalt und dessen Toleranz
Noyaux de ferrite - Inductance spécifique normalisée pour noyaux à entrefer et tolérances associées
La CEI 62358:2012 fournit les valeurs AL normalisées (inductances spécifiques) ainsi que les tolérances associées des circuits magnétiques en pots, des noyaux carrés (RM), des noyaux ETD, des noyaux E, des noyaux EER, des noyaux EP, des noyaux PQ et des noyaux de ferrite faible hauteur. Cette édition inclut les modifications techniques significatives suivantes par rapport aux éditions antérieures: a) ajout de la valeur AL (inductance spécifique) et ses tolérances pour les noyaux PQ; b) ajout de la valeur AL (inductance spécifique) et ses tolérances pour les noyaux EFD; c) ajout de la valeur AL (inductance spécifique) et ses tolérances pour les noyaux ER-I-Faible hauteur; d) ajout de la valeur AL (inductance spécifique) et ses tolérances pour les noyaux ER Faible hauteur (Les noyaux ferrites ER9,5 x 2,5 x 5, ER11 x 2,5 x 6, ER14,5 x 3 x 7 sont les mêmes que dans l'édition antérieure); e) ajout de la valeur AL (inductance spécifique) et ses tolérances pour les noyaux PQ-I Faible hauteur.
Feritna jedra - Standardni faktor induktance za jedra z režo in njegove tolerance
Ta mednarodni standard podaja standardne vrednosti AL (faktor induktance) ter njihove tolerance Pot, RM, ETD, E, EER, EP, PQ in nizko profilnih feritnih jeder z režo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62358:2013
01-marec-2013
Feritna jedra - Standardni faktor induktance za jedra z režo in njegove tolerance
Ferrite cores - Standard inductance factor for gapped cores and its tolerance
Ferritkerne - Standard-Induktivitätsfaktor für Kerne mit Luftspalt und dessen Toleranz
Noyaux de ferrite - Inductance spécifique normalisée pour noyaux à entrefer et
tolérances associées
Ta slovenski standard je istoveten z: EN 62358:2012
ICS:
29.100.10 Magnetne komponente Magnetic components
SIST EN 62358:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62358:2013
---------------------- Page: 2 ----------------------
SIST EN 62358:2013
EUROPEAN STANDARD
EN 62358
NORME EUROPÉENNE
December 2012
EUROPÄISCHE NORM
ICS 29.100.10 Supersedes EN 62358:2004
English version
Ferrite cores -
Standard inductance factor for gapped cores and its tolerance
(IEC 62358:2012)
Noyaux de ferrite - Ferritkerne -
Inductance spécifique normalisée pour Standard-Induktivitätsfaktor für Kerne mit
noyaux à entrefer et tolérances associées Luftspalt und dessen Toleranz
(CEI 62358:2012) (IEC 62358:2012)
This European Standard was approved by CENELEC on 2012-11-16. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62358:2012 E
---------------------- Page: 3 ----------------------
SIST EN 62358:2013
EN 62358:2012 - 2 -
Foreword
The text of document 51/1005/FDIS, future edition 2 of IEC 62358, prepared by IEC TC 51, "Magnetic
components and ferrite materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62358:2012.
The following dates are fixed:
• latest date by which the document has (dop) 2013-08-16
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-11-16
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 62358:2004.
EN 62358:2012 includes the following significant technical changes with respect to EN 62358:2004:
a) addition of AL value (inductance factor) and its tolerance for PQ-cores;
b) addition of AL value (inductance factor) and its tolerance for EFD-cores;
c) addition of AL value (inductance factor) and its tolerance for Low-profile ER-I-cores;
d) addition of AL value (inductance factor) and its tolerance for Low-profile ER-cores
(ER9,5 × 2,5 × 5, ER11 × 2,5 × 6, ER14,5 × 3 × 7 ferrite cores are same as in EN 62358:2004);
e) addition of AL value (inductance factor) and its tolerance for Low-profile PQ-I-cores.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 62358:2012 was approved by CENELEC as a European
Standard without any modification.
---------------------- Page: 4 ----------------------
SIST EN 62358:2013
- 3 - EN 62358:2012
Annex ZA
(normative)
Normative references to i nternational publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 61185 - Ferrite cores (ETD-cores) intended for use in EN 61185 -
power supply applications - Dimensions
IEC 61596 - Magnetic oxide EP-cores and associated EN 61596 -
parts for use in inductors and transformers -
Dimensions
IEC 62044-2 - Cores made of soft magnetic materials - EN 62044-2 -
Measuring methods -
Part 2: Magnetic properties at low excitation
level
IEC 62317-2 - Ferrite cores - Dimensions - EN 62317-2 -
Part 2: Pot-cores for use in
telecommunications, power supply, and filter
applications
IEC 62317-4 - Ferrite cores - Dimensions - EN 62317-4 -
Part 4: RM-cores and associated parts
IEC 62317-7 - Ferrite cores - Dimensions - EN 62317-7 -
Part 7: EER-cores
IEC 62317-8 - Ferrite cores - Dimensions - EN 62317-8 -
Part 8: E-cores
IEC 62317-9 - Ferrite cores - Dimensions - EN 62317-9 -
Part 9: Planar cores
IEC 62317-13 - Ferrite cores - Dimensions - EN 62317-13 -
Part 13: PQ-cores for use in power supply
applications
ISO 497 - Guide to the choice of series of preferred - -
numbers and series containing more rounded
values of preferred numbers
---------------------- Page: 5 ----------------------
SIST EN 62358:2013
---------------------- Page: 6 ----------------------
SIST EN 62358:2013
IEC 62358
®
Edition 2.0 2012-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Ferrite cores – Standard inductance factor for gapped cores and its tolerance
Noyaux de ferrite – Inductance spécifique normalisée pour noyaux à entrefer et
tolérances associées
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX R
ICS 29.100.10 ISBN 978-2-83220-398-9
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 62358:2013
– 2 – 62358 © IEC:2012
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Measuring method . 6
4 A value and its tolerance . 6
L
4.1 General . 6
4.2 Tolerance . 7
4.3 E-core . 7
4.4 ETD-core and EER-core . 7
4.5 EP-core . 7
4.6 RM-core . 7
4.7 Pot-core . 7
4.8 PQ-core . 7
4.9 Low-profile core . 7
Table 1 – Tolerance versus letter code . 7
Table 2 – A and its tolerance for E-cores (IEC 62317-8) . 8
L
Table 3 – A and its tolerance for ETD-cores (IEC 61185) and EER-cores (IEC 62317-7) . 10
L
Table 4 – A and its tolerance for EP-cores (IEC 61596) . 11
L
Table 5 – A and its tolerance for RM-cores (IEC 62317-4) . 11
L
Table 6 – A and its tolerance for Pot-cores (IEC 62317-2) . 12
L
Table 7 – A and its tolerance for PQ-cores (IEC 62317-13) . 13
L
Table 8 – A and its tolerance for EL-cores (IEC 62317-9) . 13
L
Table 9 – A and its tolerance for EL-I (plate)-cores (IEC 62317-9) . 14
L
Table 10 – A and its tolerance for low-profile ER-I (plate)-cores (IEC 62317-9) . 15
L
Table 11 – A and its tolerance for low-profile ER-cores (IEC 62317-9) . 16
L
Table 12 – A and its tolerance for low-profile E-I (plate)-cores (IEC 62317-9) . 17
L
Table 13 – A and its tolerance for low-profile E-cores (IEC 62317-9) . 17
L
Table 14 – A and its tolerance for low-profile RM cores (IEC 62317-4) . 18
L
Table 15 – A and its tolerance for low-profile PQ-I (plate)-cores (IEC 62317-13) . 18
L
---------------------- Page: 8 ----------------------
SIST EN 62358:2013
62358 © IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
_____________
FERRITE CORES – STANDARD INDUCTANCE
FACTOR FOR GAPPED CORES AND ITS TOLERANCE
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62358 has been prepared by IEC technical committee 51:
Magnetic components and ferrite materials.
This second edition cancels and replaces the first edition published in 2004. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
editions:
a) addition of A value (inductance factor) and its tolerance for PQ-cores;
L
b) addition of A value (inductance factor) and its tolerance for EFD-cores;
L
c) addition of A value (inductance factor) and its tolerance for Low-profile ER-I-cores;
L
d) addition of A value (inductance factor) and its tolerance for Low-profile ER-cores
L
(ER9,5 × 2,5 × 5, ER11 × 2,5 × 6, ER14,5 × 3 × 7 ferrite cores are same as the previous
edition);
e) addition of A value (inductance factor) and its tolerance for Low-profile PQ-I-cores.
L
---------------------- Page: 9 ----------------------
SIST EN 62358:2013
– 4 – 62358 © IEC:2012
The text of this standard is based on the following documents:
FDIS Report on voting
51/1005/FDIS 51/1008/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 10 ----------------------
SIST EN 62358:2013
62358 © IEC:2012 – 5 –
INTRODUCTION
The A value (inductance factor) and its tolerance have been specified by the users before.
L
When manufacturers wish to have an inventory for short delivery, they have to hold the
products before gapping since there is no standard for the A value. Because of electronic
L
commerce and the increased demand for rapid delivery of products, it will be more convenient
for customer
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.