SIST EN ISO 19066-1:2015

Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19066-1:2014)

This part of ISO 19066 establishes a system of designation for methyl methacrylate-acrylonitrilebutadiene-
styrene (MABS) moulding and extrusion materials, which can be used as the basis for
specifications.
The types of MABS plastic are differentiated from each other by a classification system based on
appropriate levels of the designatory properties
a) Vicat softening temperature,
b) melt volume-flow rate,
c) Charpy notched impact strength, and
d) tensile modulus,
and on information about composition, intended application and/or method of processing, important
properties, additives, colorants, fillers, and reinforcing materials.
This part of ISO 19066 is applicable to all methyl methacrylate-acrylonitrile-butadiene-styrene materials
consisting of a continuous phase based mainly on copolymers of styrene (and/or an alkyl-substituted
styrene), acrylonitrile and methyl methacrylate, and a dispersed elastomeric phase based on butadiene.
It applies to MABS materials ready for normal use in the form of powder, granules, or pellets, unmodified
or modified by colorants, additives, fillers, etc.
It is not intended to imply that materials having the same designation give necessarily the same
performance. This part of ISO 19066 does not provide engineering data, performance data, or data on
processing conditions which might be required to specify a material for a particular application and/or
method of processing.
If such additional properties are required, they will be determined in accordance with the test methods
specified in ISO 10366-2, if suitable.
In order to specify a thermoplastic material for a particular application or to ensure reproducible
processing, additional requirements can be given in data block 5 (see 3.1).

Kunststoffe - Methylmethacrylat-Acrylnitril-Butadien-Styrol (MABS)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 19066-1:2014)

1.1   In diesem Teil von ISO 19066 wird ein Bezeichnungssystem für thermoplastische Methylmethacrylat-Acrylnitril-Butadien-Styrol (MABS)-Formmassen festgelegt, das als Grundlage für Spezifikationen dienen kann.
1.2   MABS Formmasse-Typen werden mit Hilfe eines Einteilungssystems voneinander unterschieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaften:
a)   Vicat-Erweichungstemperatur,
b)   Schmelze-Volumenfließrate,
c)   Charpy-Kerbschlagzähigkeit,
d)   Zug-Modul
und auf Informationen über Zusammensetzung, vorgesehene Anwendung und/oder Verarbeitungsverfahren, wichtige Eigenschaften, Additive, Farbstoffe, Füll- und Verstärkungsstoffe beruht.
1.3   Dieser Teil von ISO 19066 ist anwendbar auf alle Methylmethacrylat-Acrylnitril-Butadien-Styrol-Formmassen mit einer kontinuierlichen Phase vorwiegend auf der Basis von Copolymeren des Styrols (und/oder alkylsubstituierten Styrols), Acrylnitrils und Methylmethacrylats und einer dispersen elastomeren Phase auf der Basis von Butadien.
Er gilt für gebrauchsfertige MABS Formmassen in Form von Pulver, Granulaten oder Pellets, nicht modifiziert oder modifiziert mit Farbstoffen, Additiven, Füllstoffen usw.
1.4   Es soll nicht unterstellt werden, dass Formmassen mit gleicher Bezeichnung notwendigerweise auch das gleiche Leistungsverhalten aufweisen. Dieser Teil von ISO 19066 enthält keine technischen Daten, Leistungsangaben oder Daten zu Verarbeitungsbedingungen, die möglicherweise notwendig sind, um eine Formmasse für eine spezielle Anwendung und/oder ein bestimmtes Verarbeitungsverfahren zu spezifizieren.
Wenn derartige zusätzliche Eigenschaften erforderlich sind, müssen sie, soweit möglich, in Übereinstimmung mit den in ISO 10366 2 festgelegten Prüfverfahren bestimmt werden.
1.5   Um eine thermoplastische Formmasse für eine bestimmte Anwendung zu spezifizieren oder eine reproduzierbare Verarbeitung sicherzustellen, dürfen zusätzliche Anforderungen im Daten-Block 5 festgelegt werden (siehe 3.1).

Plastiques - Méthacrylate de méthyle-acrylonitrile-butadiène-styrène (MABS) pour moulage et extrusion - Partie 1: Système de désignation et base de spécifications (ISO 19066-1:2014)

L'ISO 19066-1:2014 établit un système de désignation des matériaux plastiques (méthacrylate de méthyle)-acrylonitrile-butadiène-styrène (MABS) pour moulage et extrusion qui peut être utilisé comme base pour les spécifications. Les types de plastiques MABS sont différenciés les uns des autres par un système de classification fondé sur des niveaux appropriés des propriétés de désignation:
a)    température de ramollissement Vicat,
b)    indice de fluidité à chaud en volume,
c)    résistance au choc Charpy avec entaille, et
d)    module de traction,
et des informations concernant la composition, l'application prévue et/ou la méthode de mise en ?uvre, les propriétés importantes, les additifs, les colorants, les charges et les matériaux de renfort.

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje na osnovi metilmetakrilat-akrilonitril-butadien-stirena (MABS) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 19066-1:2014)

Ta del standarda ISO 19066 določa sistem označevanja materialov za oblikovanje in ekstrudiranje na osnovi metilmetakrilat-akrilonitril-butadien-stirena (MABS), ki jih je mogoče uporabiti kot podlago za specifikacije.
Vrste polimernih materialov na osnovi metilmetakrilat-akrilonitril-butadien-stirena se ločujejo glede na sistem razvrščanja, ki temelji na ustreznih ravneh označevalnih lastnosti:
a) temperaturi zmehčišča po Vicatu,
b) prostorninskem pretoku taline,
c) zarezni udarni žilavosti po Charpyju,
d) nateznih modulih
in informacijah o sestavi, nameravani uporabi in/ali metodi obdelave, pomembnih
lastnostih, aditivih, barvilih, polnilih ter materialih za ojačanje.
Ta del standarda ISO 19066 se uporablja za vse materiale na osnovi metilmetakrilat-akrilonitril-butadien-stirena,
ki so sestavljeni iz snovnega polnila na osnovi stirenskega kopolimera (in/ali alkil nadomestnega
stirena), akrilonitrila in metilmetakrilata ter razpršenega polnila iz elastomera na osnovi butadiena.
Uporablja se za materiale na osnovi metilmetakrilat-akrilonitril-butadien-stirena v obliki praška, granul ali peletov, pripravljene za običajno uporabo, nespremenjene ali spremenjene z barvili, aditivi, polnili itd.
Materiali z enako oznako nimajo nujno tudi enakih lastnosti. Ta del standarda ISO 19066 ne zagotavlja inženirskih podatkov, podatkov o delovanju ali podatkov o
pogojih obdelave, ki so morda potrebni za določitev materiala za določeno uporabo in/ali
metodo obdelave.
Če so take dodatne lastnosti zahtevane, se določijo v skladu s preskusnimi metodami
iz standarda ISO 10366-2, če je to primerno.
Da bi se določil termoplastični material za določeno uporabo ali da bi se zagotovila obnovljiva obdelava, je mogoče v podatkovnem bloku 5 navesti dodatne zahteve (glejte 3.1).

General Information

• Status: Published
• Publication Date: 17-Nov-2014
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 13-Nov-2014
• Due Date: 18-Jan-2015
• Completion Date: 18-Nov-2014
• Ref Project: EN ISO 19066-1:2014 - Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19066-1:2014)

Relations

• Replaces: SIST EN ISO 10366-1:2003 - Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 10366-1:2002)
• Effective Date: 01-Jan-2015

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 19066-1:2015
01-januar-2015
1DGRPHãþD
SIST EN ISO 10366-1:2003
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHQDRVQRYL
PHWLOPHWDNULODWDNULORQLWULOEXWDGLHQVWLUHQD0$%6GHO6LVWHPR]QDþHYDQMDLQ
SRGODJH]DVSHFLILNDFLMH,62
Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and
extrusion materials - Part 1: Designation system and basis for specifications (ISO 19066-
1:2014)
Kunststoffe - Methylmethacrylat-Acrylnitril-Butadien-Styrol (MABS)-Formmassen - Teil 1:
Bezeichnungssystem und Basis für Spezifikationen (ISO 19066-1:2014)
Plastiques - Méthacrylate de méthyle-acrylonitrile-butadiène-styrène (MABS) pour
moulage et extrusion - Partie 1: Système de désignation et base de spécifications (ISO
19066-1:2014)
Ta slovenski standard je istoveten z: EN ISO 19066-1:2014
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 19066-1:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 19066-1:2015

---------------------- Page: 2 ----------------------

SIST EN ISO 19066-1:2015

EUROPEAN STANDARD
EN ISO 19066-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2014
ICS 83.080.20 Supersedes EN ISO 10366-1:2002
English Version
Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene
(MABS) moulding and extrusion materials - Part 1: Designation
system and basis for specifications (ISO 19066-1:2014)
Plastiques - Matériaux plastique (méthacrylate de méthyle)- Kunststoffe - Methylmethacrylat-Acrylnitril-Butadien-Styrol
acrylonitrile-butadiène-styrène (MABS) pour moulage et (MABS)-Formmassen - Teil 1: Bezeichnungssystem und
extrusion - Partie 1: Système de désignation et base de Basis für Spezifikationen (ISO 19066-1:2014)
spécifications (ISO 19066-1:2014)
This European Standard was approved by CEN on 6 September 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19066-1:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 19066-1:2015
EN ISO 19066-1:2014 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 19066-1:2015
EN ISO 19066-1:2014 (E)
Foreword
This document (EN ISO 19066-1:2014) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2015, and conflicting national standards shall be withdrawn at the
latest by April 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10366-1:2002.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19066-1:2014 has been approved by CEN as EN ISO 19066-1:2014 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 19066-1:2015

---------------------- Page: 6 ----------------------

SIST EN ISO 19066-1:2015
INTERNATIONAL ISO
STANDARD 19066-1
First edition
2014-10-01
Plastics — Methyl methacrylate-
acrylonitrile-butadiene-styrene
(MABS) moulding and extrusion
materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Matériaux plastique (méthacrylate de méthyle)-
acrylonitrile-butadiène-styrène (MABS) pour moulage et extrusion —
Partie 1: Système de désignation et base de spécifications
Reference number
ISO 19066-1:2014(E)
©
ISO 2014

---------------------- Page: 7 ----------------------

SIST EN ISO 19066-1:2015
ISO 19066-1:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 19066-1:2015
ISO 19066-1:2014(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Designation system . 2
3.1 General . 2
3.2 Data block 1 . 2
3.3 Data block 2 . 3
3.4 Data block 3 . 3
3.5 Data block 4 . 4
3.6 Data block 5 . 6
4 Example of a designation . 6
© ISO 2014 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 19066-1:2015
ISO 19066-1:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials.
This first edition of ISO 19066-1 cancels and replaces ISO 10366-1:2002, which has been technically
revised to introduce a new designation system.
The revised designation system is published under a new ISO number, as many existing documents
refer to ISO 10366-1. If the existing ISO 10366-1 would be replaced by the new designation system, these
documents would refer to the incorrect designation system.
In order to give users time to switch from ISO 10366-1 to ISO 19066-1, ISO 10366-1 needs to be phased
out in 5 to 10 years. During this period, ISO 10366-2 will effectively be Part 2 of this International
Standard.
ISO 19066 consists of the following parts, under the general title Plastics — Methyl methacrylate-
acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials:
— Part 1: Designation system and basis for specifications
iv © ISO 2014 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 19066-1:2015
ISO 19066-1:2014(E)

Introduction
ISO 10366-1:2002 is complex and does not fit with daily practice anymore. In practice ISO 1043 and
ISO 11469 are, in combination, ‘improperly’ being used as a designation system for, e.g. marking. The
aim of this International Standard is to simplify the data block system and to connect more to ISO 1043
and ISO 11469, where the first two blocks are used for generic identification and marking of products.
© ISO 2014 – All rights reserved v

---------------------- Page: 11 ----------------------

S
...